A Study of the Vertical Vibration of the 4200 Thick Plate Rolling Mills

In this paper,the mill stand and the rolled piece were studied as a system. Based on the disoreted masses and the deformation of bending curve of the roller and roll housing, according to Rayleigh method,the equivalent mass and and the equivalent stiffness of the mode were solved,and set up a multiple degree of freedom vibration dynamic model. And also did theoretical analysis and calculation with an exapmle of the 4200 thick plate rolling mills.     

THE STUDY OF STRAIN FATIGUE CRACK PROPAGATION BEHAVOURS OF VANADIUM BEARING HSLA STEEL

In this paper, the strain fatigue: crack propagation rates of vanadium bearing HSLA steel with different micro-structures are measured under constant load conditions, and the relationship between the crack propagation rate and the microstructures of steel is also studied.     

A Study on the Mathematical Models for Two Dimensional Guillotine Cullting-stock

Based on the analysis and study on some existed models for two-dimensional Guillotine Cutting-Stock problem, it is pointed out that some kinds of the models may miss some good cutting patterns,and some may result in inadequate solutions because of only considering the patterns with the smallest waste. A kind of revised two-dimensional cutting-stock models are developed,which transform the two-dimensional problem into the one-dimensional one using the dimension-decreasing heuristic method and whose initial patterns are considered comprehensively. In this kind of models, not only the least waste,but also the other constraints,such as the demands and the relative area of the order plates are considered.     

A Study on the Practical Algorithm for One Dimensional Equal Stock Cutting Problem

Based on alalysing the mathematical models for one dimensional equal stock cutting problem,a knapsack column generation algorithm has been constructed,which is a successive approximate algorithm for the practical engineering.In the end of this paper,some computational examples have been presented,which show that the convergence and optimum results of the algorithm are quite good.     

黄麻工艺纤维细度的研究

研究表明：圆果种比长果种工艺纤维支数高65公支左右；品种间差异极显著；工艺纤维细度与单株原麻重等5个经济性状呈极显著负相关，与出麻率等性状呈显著正相关；麻株各部位中以中部工艺纤维支数最高，梢部次之，基部最低；适时播种、适当密植、适量适时施肥，适时早收等栽培技术措施能提高工艺纤维支数。通过对构成产量和工     

几个外引水稻品种在河南沿黄地区的表现

通过对几个外引水稻品种在河南沿黄地区引种试验，表明杂交稻生长速度快，抽穗较晚，但分蘖力强、成穗率高、穗粒数多，产量的增产潜力较大。除金世纪外其他几个品种与豫粳6号相比基本持平，但产量也有不同程度的提高。但金世纪品质与豫粳6号相比有较大的提高，产量也提高。     

赤霉素处理对大白菜阶段发育的影响

用赤霉素处理未通过春化阶段的大白菜，植株可以抽薹开花；赤霉素处理已通过春化阶段的大白菜，可以促进植株提前抽薹开花。大白菜品种不同，赤霉素处理的效果有差异。     

散叶烤房系列研究 2.装炕技术研究

为解决散叶烤房烟叶堆放问题，采用插板式装烟法和自然堆积法研究了散叶烤房的装炕技术，结果表明：散叶烤房装烟时以自然堆积法，稍稍用力推挤，单层密度保持在75~85kg/m3为宜，并提出了相应的采收和装炕技术要点，即下部叶适时早收，中部叶尚熟至适熟采收，上部叶充分成熟采收。装炕时烟束要叠放整齐，叶片背面靠向界墙方向，正面面向装烟者，保持叶片与装烟板水平面夹角70~80°，一层靠一层。     

X射线灭活活体日本沼虾精子的初步研究

为检测X射线对日本沼虾精子的灭活效果,利用X射线对雄性日本沼虾进行不同时间的照射处理,将处理后的雄虾与刚完成生殖脱壳的雌虾交配。待雌虾产卵后,计数雌虾抱卵天数,并在显微镜下观察卵的畸形情况。X射线管照射强度为100 k V,5 m A,源距10 cm,照射时间为0、30、60、90、120 min。结果发现:照射30 min组的抱卵天数及卵的畸形率较0 min组无变化,卵的畸形率为0,卵能正常发育至孵化出膜。随着照射时间的增加,在30~90 min之间,雌虾抱卵天数逐渐减少,且所抱卵的畸形率呈上升趋势。照射120 min组的抱卵天数较90 min组变化不大,卵的畸形率达100%。在本试验照射时间范围(0~120 min)内,灭活日本沼虾精子遗传物质的最佳照射时间为90~120 min。