碳酸盐法制水泥稻草板的研究

采用施加释放二氧化碳的添加剂，近似于普通刨花板的热压工艺，利用正交试验对水泥稻草板的快速固化工艺进行试验：讨论了水灰比、草灰比、添加剂用量对板子性能的影响。结果表明：水泥稻草板的快速固化工艺可行，添加释放二氧化碳的碳酸盐制板的最佳制板工艺参数为：草灰比1：6，水灰比0．5，碳酸氢钾为水泥加量的10％。     

原状粉煤灰在水泥刨花板中应用的研究

主要论述了原状粉煤灰（Ⅲ级灰）在水泥刨花极中应用的情况。分析了在其它工艺条件（密度、水灰比、木灰比）确定情况下,粉煤灰替代量、外加剂种类和用量等因素对板各项性能指标的影响。结果表明：（１）粉煤灰替代量是影响极材性能的主要因素,外加剂种类和用量对极性能也有影响;（２）粉煤灰替代量３０％为强度转折点,但４０％替代量制板,板各性能指标仍然能达到国家行业标准要求;（３）以粉煤灰替代部分水泥生产水泥刨花板。不但可以降低生产成本,而且可以改善板的某些性能。     

冷压法粉煤灰水泥刨花板工艺研究

粉煤灰水泥刨花板是一种符合墙体材料发展方向的新型建筑材料,在预备性实验基础上,采用二次正交旋转组合设计对粉煤灰水泥刨花板进行工艺试验,结果表明,在实验设计取值范围内,板密度,水灰比及水玻璃（Na2SiO3)用量对板性能（MOR,MOE,IB）影响显著,灰木比对吸水厚度膨胀率（TS）影响特别显著。     

二氧化碳在水泥粉煤灰刨花生产中的应用

１ 水泥粉煤灰刨花板简介 在水泥刨花板生产中以一定量的粉煤灰替代一定比例的水泥生产出来的板材称之为水泥粉煤灰刨花板。其不仅具有水泥刨花板的各种优良性能，而且生产中利用了粉煤灰这一工业废物，既降低了生产成本，又保护了环境，还可以获得国家的优惠政策。２二氧化碳在水泥粉媒灰刨花板生产中的应用机理 从水泥和粉煤灰的成分以及它们与水的反应情况看，水泥和粉煤灰在成品水泥粉煤灰刨花板中主要是以硅酸钙和氢氧化钙晶体形态存在．但在没有人为改变反应环境的情况下有些反应速度太慢，在经过较长时间水泥浆硬化后反应仍然存在。…     

快速固化水泥刨花板的工艺试验

以速生杉木加工剩余物为主要原料、Na2SiO3为快速固化添加剂制备水泥刨花板,研究了冷、热压两种压板方式、Na2SiO3添加量、热压温度、热压时间、水灰比、灰木比、水泥种类和刨花形态等因素对水泥刨花板主要性能的影响.结果表明,热压法可适用于水泥刨花板制造,最佳工艺条件为:Na2SiO3添加量10%、热压温度95℃、热压时间12 min、水灰比0.6、灰木比2.6,制备的水泥刨花板的静曲强度达到10 MPa;采用MgCl2后处理能显著改善板的性能.     

喷蒸热压法和传统热压法生产杨木刨花板的比较(Ⅰ)喷蒸热压对刨花板力学强度的影响(英文)

该研究以杂种毛白杨无性系（ＰｏｐｕｌｕｓｔｏｍｅｎｔｏｓａＢＬ）４年生幼龄格为原料，应用喷蒸坟和传统热压两种方法来生产杨木刨花板．刨花板内施胶量为１０％的脲醛树脂胶（ＵＦ），目标厚度分别取１０，１５，２０，２５ｍｍ，热压温度固定在１８０℃．喷蒸热压时所用饱和蒸汽的压力为０３～０５ＭＰａ，每种厚度下喷时间一定，取两个压时间；传统热压时每种厚度下各取４个热压时间．然后测定刨花板试件的力学强度和物理性能．在这部分里，主要讨论了责任中热压法生产的刨花板的静曲强度和内结合强度．结论为：相对于传统热压法，喷蒸热压可以明显缩短杨木刨花板生产所需的热压时间，而且使刨花板具有优异的内结合强度；但是，它对饱花板的静曲强度并没有显著影响     

异氰酸酯胶无毒低密度杉木刨花板的制造

本研究探讨了用异氰酸酯胶粘剂制造低密度杉木刨花板的工艺条件,讨论了施胶量、热压温度、热压时间、热压压力和刨花含水率对板材性能的影响。结果表明,当板材密度为０．４３～０．４８ｇ／ｃｍ＾２时,施胶量只需５％,刨花含水率适应范围广,所制成的刨花板无毒,耐水性好。     

竹木混合水泥刨花板工艺初步研究

研究了热压法制造竹木混合水泥刨花板工艺并对影响板材性能的因素进行探讨。结果表明:竹刨花水煮预处理后所制备的板材性能较好;本实验范围内,竹木混合水泥刨花板较合适的工艺参数为竹木比1∶3、灰木比4∶1、热压时间1～2min/mm板厚、CaCl2用量为灰重的5%、水灰比0.4。     

热压水泥刨花板工艺的研究

本文主要论述了热压法制造水泥刨花板的工艺。试验选取热压温度、热压时间、水灰比、灰木比、添加剂和板子密度等工艺变量建立多元回归方程,并对刨花形态等问题进行了讨论。试验结果表明:热压温度和刨花形态对板子性能影响极为显著;热压法水泥刨花板不仅具有与冷压法相同的物理力学性能,而且还具有水泥水化速度快、板坯脱模强度较高等特点,因而缩短了水泥刨花板的生产过。     

异氰酸酯胶在刨花板中的应用

异氰酸酯胶作为刨花板胶粘剂，具有刨花含水率适应范围广（０～２５％），施胶量低、无游离甲醛释放、适合制造轻质刨花板等优点。施胶量为５％、密度为０．４５ｇ／ｃｍ３和０．６１ｇ／ｃｍ￣３的二苯基甲烷二异氰酸酯（ＭＤＩ）小黑杨刨花板的物理力学性能分别达到Ａ类刨花板二等品和优等品的指标要求。密度为０．６５ｇ／ｃｍ￣３时，只要ＭＤＩ施胶量达到３％，刨花板的物理力学性能指标能达到Ａ类刨花板的国家标准要求。试验还表明：ＭＤＩ具有较好的耐水性，但耐湿热性和长期耐水性不如酚醛胶。生产１ｍ￣３刨花板ＭＤＩ与ＰＦ和ＵＦ胶粘剂成本比为２．０５：１．７８：１．００。     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Decomposition and nutrient loss from prunings of different contour hedgerow species in tea plantations in the sloping highlands of Sri Lanka

Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week⁻¹ for leaves and from 0.0225 to 0.0633 week⁻¹ for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient enrichment capacity and slower decomposition rates which would minimize leaching losses. This revised version was published online in June 2006 with corrections to the Cover Date.     

Effects of Seed Weight and Seed Type on Early Seedling Growth of Pinus sylvestris under Harsh and Optimal Conditions

The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions.     

Potential to harness superior nutritional qualities of exotic baobabs if local adaptation can be conferred through grafting

Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral contents and B₁ and B₂ vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B₁ 88 mg 100 g⁻¹, B₂ 187 mg 100 g⁻¹, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations.     

Modelling of adequate pretwist for obtaining straight timber

Abstract

Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Growth of Phlebiopsis gigantea in wood of seven conifer species

Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered.