Variability of wood properties in two wild cherry clonal trials

There has been an increase in wild cherry cultivation over recent decades, revealing a need for improvements in planting material to be used for the production of high quality timber. To date, trial tests have been carried out mainly on growth and tree architectural traits, while no investigations have focused on wood properties. The present study investigated the variability of the growth traits and the physical and mechanical properties of wild cherry wood, both within the tree, within and among clones and between sites. The aims of the study are to provide useful information on the genetics of wood traits in valuable hardwoods and to discuss how within-tree variation can affect early selection of genotypes. The results suggest that site was the most important source of variation in growth traits and in the proportion of heartwood, although differences among clones were highly significant. The number of sapwood rings was very homogeneous both between sites and among clones. Concerning the wood traits, most variation was detected within the tree, rather than within or among clones or between sites. Within tree variability seems to be mainly due to heartwood/sapwood presence. However, since there is a high correlation between heartwood and sapwood properties, a quite efficient selection made on the basis of sapwood should provide an efficient means of selecting heartwood traits.     

Variation of heartwood phenolics and oak lactones between the species and phenological types of Quercus petraea and Q. robur

Pressler cores were taken of Quercus petraea and Q. robur treesfrom young German provenance stands and mature mixed plantationsin England. The concentration of total phenolics extracted fromthe outer heartwood was measured and significant differencesfound between the two species. Concentrations of oak lactones,measured from provenance samples, also varied significantlybetween the species. However, the difference in total phenolicsbetween species was much lower among the trees from the mixedplantations than from the provenance trials. Q. petraea wascharacterized by lower levels of total phenolics but greaterconcentrations of oak lactones than Q. robur. A comparison betweenlate and early flushing Q. petraea trees found no significantdifference in total phenolics between these phenological types.     

Variability in physical properties of plantation-grown progenies of Melia composita and determination of a kiln-drying schedule

Plantation-grown progenies of Melia composita Willd.were studied for variability in several physical properties: density,radial and tangential shrinkage,longitudinal permeability of heartwood and sapwood.Furthermore,flat-sawn planks from each of the progeny were subjected to a quick-drying test for determination of kilndrying schedule.The mean density of the species was 0.39 g cm~(-3) and the wood may be categorized as light wood.Mean radial shrinkage(%) for the species was 2.8% with progeny-wise variation in radial shrinkage from 1.56 to 4.11%.Mean tangential shrinkage(%) for the species was 5.54% with progeny-wise variation in tangential shrinkage from 3.69 to 7.71%.The resultant tangentialradial shrinkage ratio was 1.98(less than two),which suggests that the wood is relatively stable with respect to drying behavior.Mean sapwood and heartwood longitudinal permeability of the species were 3.38 and 2.02 Darcy,respectively.Higher longitudinal permeability of sapwood and heartwood indicate better drying and preservative properties of the species.Terazawa quick-drying test method suggests that the species is less susceptible to drying defects.During the test,only moderate checks and cracks were observed.A tentative kiln-drying schedule was recommended based on these results.     

The concentration of phenolics in brown-rot decay resistant and susceptible Scots pine heartwood

The concentrations of three individual stilbenes, pinosylvin (PS), pinosylvin monomethyl ether (PSM), and pinosylvin dimethyl ether (PSD), and the total concentration of phenolic compounds were determined in 34-year-old Scots pines which were known to have either decay-resistant or susceptible heartwood. The sample trees were selected from two progeny tests among 783 trees; the decay resistance of which had been screened earlier in vitro against a brown-rot fungus Coniophora puteana. Ten decay-resistant and ten susceptible trees from each of the progeny tests were analysed. In the heartwood of the resistant trees, the average total concentration of the stilbenes was 7.5 and 6.4 mg/g of dry weight, while in the heartwood of the susceptible trees the respective values were 5.0 and 4.7 mg/g. The difference between the decay resistant and susceptible trees was statistically significant in both progeny tests. The difference in concentration of total phenolics, analysed by the Folin-Ciocalteu method, was also significant. A high concentration of phenolics was connected to the low hygroscopicity of wood. The results support the argued hypothesis that the stilbenes make a contribution to the differences in the decay rate of natural wood substrate. On the other hand, the results show that the stilbenes alone do not explain the variation in decay rate.     

Clonal variation of carbon content in wood of Larix kaempferi (Japanese larch)

Variations in carbon content in wood among 102 clones, selected from almost the entire natural distribution area, were investigated in Larix kaempferi. The average carbon content was 50.50%, 50.94%, and 50.80% in sapwood, heartwood, and whole wood, respectively. The difference in carbon content between clones was significant. The clonal repeatabilities were 0.46, 0.38, and 0.44 in heartwood, sapwood and whole wood, respectively. The coefficients of variation in the clonal mean carbon content were only 0.43%, 0.42%, and 0.41% in heartwood, sapwood, and whole wood, respectively. This small genetic variation and resulting small relative genetic gain of carbon content indicate that the genetic improvement of carbon content by selection has a small effect on the genetic improvement of carbon sequestration capacity by selection in L. kaempferi.     

广西融水特色红心杉木优树材质性状变异规律研究

[目的]通过测定和分析广西融水种源红心杉木优树材质性状指标,以了解该地区红心杉木材性状变异规律。[方法]以广西融水种源60株20年生的红心杉木优树为研究材料,测定单株材积、红心率、基本密度、组织比量、管胞性状、微纤丝角等10个材质性状指标,分析各材性性状指标分布和变异规律及性状间的相关关系。[结果]表明:红心率、基本密度、木射线比量、管胞比量、管胞长、管胞宽、管胞长宽比等性状数据分布服从正态分布。融水两个地区红心杉优树轴向薄壁细胞比量的变异系数分别为35.08%和44.97%,变异较大。管胞比量变异系数分别为3.28%和3.56%,变异较小。红心率、木射线比量、管胞长、管胞宽、微纤丝角等性状差异极显著(P0.01),轴向薄壁细胞比量差异显著(P0.05)。10个材质性状间存在12对表型显著相关。[结论]测定的10个性状均是连续性数量性状。早、晚材的管胞长度、管胞宽度和管胞长宽比等性状数据呈从心材至边材逐渐增加的规律。作为重要经济性状的红心率与木射线比量呈极显著正相关(P0.01),单株材积与轴向薄壁细胞比量呈显著正相关(P0.05),而单株材积与基本密度的相关性不显著,这使红心杉木生长量与材性相结合的遗传改良成为可能。     

Genetic and environmental variation in wood properties of <Emphasis Type="Italic">Acacia melanoxylon</Emphasis>

Context  

Australian blackwood (Acacia melanoxylon), is a fast-growing, high-quality, appearance-grade timber species native to eastern Australia. Some of its key wood properties are percentage heartwood, heartwood colour, basic density, wood stiffness and green moisture content. Variation in these properties affects log value, processing and marketing.     

Models for Predicting Wood Properties in Stems of Picea abies and Pinus sylvestris in Sweden

To study and model the variation of wood properties, sample trees were selected from 42 Norway spruce and 20 Scots pine stands covering a wide variation in climatic and site conditions, stand maturation and tree sizes. Plot and tree measurements were followed by sampling wood from different heights in each sample tree and laboratory measurements of wood properties. Mixed linear and non-linear prediction models were developed using diameters, number of annual rings and climatic indices as explanatory variables. The variation in spruce properties explained by these variables was: basic density 50%, latewood content 52%, juvenile wood diameter 85%, heartwood diameter 94% and bark thickness 76%. The corresponding values for pine were 59, 54, 79, 92 and 85%. Random among-tree variance was an important contributor to the remaining variation for density and latewood. In general, only a minor part of the random variation was related to variance between stands. Predictions derived from the models for density and juvenile wood in both species, and heartwood in pine showed good agreement when validated with data sets from two other studies. The resulting models may be used for predicting wood properties in forest planning and in bucking computers in harvesters, provided that the essential information is available.     

杉木无性系木材干缩性与吸水性的变异

以102个17年生杉木无性系为试材,对木材的干缩性与吸水性进行测定分析发现,木材干缩性、吸水性在杉木无性系间差异极显著;干缩性变异幅度为3.1%～20.0%,表型变异系数达59.8%;吸水性变异幅度在214.5%～338.1%间,表型变异系数为13.2%。木材干缩性与吸水性均具有明显的无性系方差分量,表明杉木木材干缩性与吸水性受遗传控制。进一步研究显示,杉木无性系木材干缩性遗传变异系数为38.6%,重复力为0.390,均属中低水平;吸水性遗传变异系数值虽较低,但重复力相对较高(0.664),属中上水平;在不同入选率(10%、20%、30%)下,木材干缩性与吸水性随入选率的降低其遗传增益值(绝对值)不断提高。研究还发现,杉木木材干缩性与木材基本密度、心材比间为极显著遗传负相关,与木材吸水性间则表现为极显著遗传正相关;木材吸水性在遗传水平上与胸径、材积、心材比间呈极显著正相关,而与木材基本密度间为极显著负相关。     

Pilodyn在桉树活立木材性质评估中的应用

测定了建立在广西22个4年生桉树无性系的Pilodyn值、木材基本密度、边材木材密度、心材木材密度和弹性模量。结果表明：Pilodyn值为9．44—15．41mm、木材密度为0．3514-0．4913g&#183;cm^-3、弹性模量在3．94GPa到7．53GPa之间;Pilodyn值在不同处理、不同方向及不同参试无性系间均存在极显著差异。Pilodyn值与各材性指标间的相关系数在-0．433到-0．755之间,呈显著到极显著负相关。研究表明,Pilodyn方法可以预测桉树活立木的木材密度和弹性模量。     

Variation of the chemical composition of Pyrenean oak (<Emphasis Type="Italic">Quercus pyrenaica</Emphasis> Willd.) heartwood among different sites and its relationship with the soil chemical characteristics

This work presents the results of a study on the variation of the chemical composition of Pyrenean oak (Quercus pyrenaica Willd.) heartwood among different sites and its relationship with the soil chemical characteristics. The chemical characteristics of the heartwood are quantified in terms of proximate and ultimate analysis, calorific value and ash composition. Subsequently, the relationship between the wood chemical characteristics and the soil characteristics was also examined. The results showed no significant differences between the wood chemical characteristics from different sites. There are, however, significant differences between trees from the same site regarding the wood ash content, the calorific value and the contents of nitrogen and hydrogen. Strong correlations were observed between the heartwood ash contents of BaO, MnO, CuO and TiO₂ and the soil nitrogen, phosphorous and potassium and the soil exchangeable base contents.     

Dependence of colour and discolouration on total extractive content of African Padauk and Jatoba

This study is about relationships between total extractive contents, heartwood colour and light-induced discolourations of the tropical species African Padauk (Pterocarpus soyauxii Taub) and Jatoba (Hymenaea courbaril L.). Wood surface colour was measured spectrophotometrically before and after light irradiation. Subsequently, the total extractive content was determined and linked to the colour parameters. Total extractive content varied between 6 % (Jatoba) and 27 % (African Padauk). The fact that non-irradiated Jatoba appeared lighter and more yellow with higher extractives contents, opposed the often assumed relationship that more heartwood extractives cause darker wood. For light-irradiated Jatoba wood only the reddishness was more intense when samples had higher extractive content. In contrast, light-irradiated African Padauk showed significant differences in all colour parameters as extractives varied. High overall colour change in African Padauk due to light irradiation was observed; however, no relationship with the extractive content existed. In contrast, discolouration rate of Jatoba wood strongly varied with its extractive content. Individual wood species react differently during exposure to light and therefore require specific surface treatment to maintain the desired colour appearance and colour stability.     

Genetic parameters of growth and wood quality traits in Picea abies

Genetic parameters were estimated for wood and growth traits in two 19-yr-old clonal trials and a 40-yr-old full-sib progeny trial of Norway spruce [Picea abies (L.) Karst.]. In the clonal trials high (>0.4) broad-sense heritabilities were found for wood density traits, lignin content, number of internal cracks, growth traits, spiral grain and number of resin canals. Moderate (0.2–0.4) heritabilities were found for tracheid lumen diameter and cell wall thickness, microfibril angle and tracheid length, while low heritabilities (<0.2) were found for pulp yield, fibre strength, wood stiffness and wood colour. Lignin content and pulp yield showed low genetic variation, whereas the genotypic coefficient of variation for most other traits ranged between 5 and 15%. Most traits showed low levels of genotype by environment interaction. Among the wood properties, latewood proportion, earlywood density and ring density showed significant, adverse correlations with volume in both clonal trials.     

Wood Density and Growth Rate of Pinus elliottii and Pinus taeda Clones Planted on Two Sites in the Eastern Transvaal / HOUTDIGTHEID EN GROEITEMPO VAN PINUS ELLIOTTI- EN PINUS TAEDA-KLONE OP TWEE GROEIPLEKKE IN OOS-TRANSVAAL GEPLANT

Eleven years old clonal plantings of Pinus elliottii and P. taeda established on two different sites were sampled to study the variation in wood density. For both species clonal differences were highly significant. Wood density at the high altitude site was consistently lower than that of the same clone at the lower altitude site. Wood density was not correlated with growth rate per site. It was further found that site x clone interaction with regard to wood density was absent, but two P. elliottii clones showed a definite site x clone interaction in respect of diameter growth rate. Density gradient differed largely between the two sites and this difference could not be explained.     

Effect of stand and tree attributes on growth and wood quality characteristics from a spacing trial with Populus xiaohei

The effect of stand density (1000 stems/ha, 500 stems/ha and 250 stems/ha) on tree growth and wood quality characteristics was studied in a 27-year-old plantation species of Populus xiaohei in China. Results indicated that stand density had significant effects on tree radial growth and crown size, and the lowest stand density produced trees with the largest stem taper. In terms of wood quality characteristics, there was no significant effect of stand density on either wood basic density or fiber length. However, significant differences were found between different stand densities for wood mechanical properties. A positive relationship between modulus of elasticity, compression strength and stand density was observed, while the highest modulus of rupture was recorded at a moderate density of 500 stems/ha. Stand density was responsible for highly significant effects on both juvenile wood and wet heartwood basal areas in individual trees, and there was an obvious tendency towards increasing juvenile wood and wet heartwood basal areas with decreasing stand density. In addition, the relationships between wood quality characteristics and tree and stand characteristics were also examined. Some wood quality characteristics, namely mechanical properties and juvenile wood and wet heartwood basal areas, were quantified successfully in relation to selected tree characteristics using a regression approach with various degrees of goodness of fit. Based on comprehensive consideration of various factors, such as wood quality, tree growth, and establishment cost, results from this study suggest that a density of 500 stems/ha is optimum for wood production.     

Element content and pH value in American black cherry (<Emphasis Type="Italic">Prunus serotina</Emphasis>) with regard to colour changes during heartwood formation and hot water treatment

Element content and pH value in wood tissues of veneer grade logs of P. serotina Ehrh. were investigated with regard to wood colour variations, measured in the CIEL*a*b* system. The average pH value of heartwood tissue was about pH 4.0 and medium colour parameters of veneer sheets were determined at L* = 73, a* = 9.8, and b* = 23.5. Optical emission spectroscopy (ICP-OES) analyses showed differences in the element contents between two regional forest sites coming from Pennsylvania and West Virginia, USA, respectively. The latter is mainly characterised by higher variations of micro-element content in the transition zone (influencing heartwood formation) and also pH value of wood tissue, which contributes to higher variations in colour response of industrially produced veneer sheets. Investigations under industrial conditions underline the correlation between length and intensity of heat treatment in veneer production and colour development: with increasing duration and temperature of hot water treatment, veneer surfaces become darker and wood colour is intensified (ΔL = 3.6, Δa = 2.1, comparing 12 and 72 h of hot water treatment at 60°C). However, no equalisation of wood colour was achieved by modifying the treatment conditions. Artificial radiation by UV–visible light, quickly and extensively darkens and intensifies wood colour (ΔL = 16, Δa = 3.5, and Δb = 4.0 after 15 h of artificial radiation), but variations in wood colour deriving from different treatment conditions during veneer production, were not reduced.     

Termite resistance and color of heartwood of hinoki (Chamaecyparis obtusa) trees in 5 half-sib families in a progeny test stand in Kyushu, Japan

Hinoki (Chamaecyparis obtusa) wood has been used as a structural material in Japan because of its superior mechanical properties, its excellent durability and the beautiful color of its heartwood. Variations of termite resistance and compositions of extractives among hinoki trees have been reported. However, genetic variation of termite resistance and the effect of heartwood color on termite resistance remain unknown. In this study, we report the characteristics of termite resistance and color indexes (L*, a* and b*) of heartwood of hinoki half-sib families in a progeny test stand. The survival days of termites and the mass loss of samples of hinoki heartwood differed significantly among hinoki families. Families with red-color heartwood had larger termite resistance than families with yellow-color heartwood. The termite resistances of individual samples from two families with yellow-color heartwood were as small as that of Pinus densiflora. Larger a* and smaller b* induced larger termite resistance of heartwood. The effect of DBH (diameter at breast height) of hinoki trees on termite resistance of hinoki families was small.     

Characterization of mean stem density,fibre length and lignin from two Acacia species and their hybrid

The objective of this study was to compare the wood properties related to wood pulp quality of two widely planted Acacia species viz.Acacia mangium Willd.and Acacia auriculiformis A.Cunn.Ex Benth.and their hybrid.Acid insoluble lignin content(Klason),mean stem density and fibre length differed considerably among the species and hybrids.A.mangium possessed a high percent of lignin content compared to A.auriculiformis and the Acacia hybrid.However,mean stem density of A.auriculiformis was higher than A.mangium and the hybrid.Fibre length of heartwood tissues was generally shorter than that of sapwood tissues.The hybrid had longer fibres than the parent species.Lignin was negatively correlated with mean stem density.Generally,the wood properties of the hybrid were superior to its parent species.The significant intraspecific variation observed for wood properties of Acacia species could be used in breeding superior hybrids combining desirable traits of the two species.Considering thedifficulty involved in accurately measuring the lignin content compared to mean stem density,selection for plants with low lignin content can be achieved by indirect selection of high mean stem density.     

Heartwood, sapwood and bark content of teak trees grown in Karnataka, India

We evaluated heartwood, sapwood and bark content in teak trees. A total of 27 sample plots were laid out in teak plantations raised by State Forest Department in Karnataka covering different age groups...     

Inter-clonal, intra-clonal, and single tree variations of wood anatomical properties and specific gravity of clonal ramets of Dalbergia sissoo Roxb.

Inter-clonal, intra-clonal and within tree variations in specific gravity and wood anatomical properties of 8-year-old grown ramets of Dalbergia sissoo Roxb. have been investigated. Radial and location-wise intra-clonal variations were non-significant for anatomical properties and specific gravity for all six clones at all three sites. However, inter-clonal variations in wood anatomical properties and specific gravity were significantly different. Inter-clonal variations in anatomical properties and specific gravity were also significant due to sites, which indicated that site-characteristics overshadowed the genetic priority of different clones for wood anatomical properties. Average fiber-characteristics of all clones showed the best performance at Lalkuan, Haldwani (site III), while average specific gravity performed well at Brandis Road, Dehradun (site I) followed by site III (Lalkuan, Haldwani) and site II (Lachchiwala, Dehradun). Within tree variations in anatomical properties like fiber length, fiber diameter, wall thickness, vessel member length and vessel member diameter due to vertical or radial direction and location (pith to periphery) are non-significant. Radial direction, location and height showed no impact on wood element variation. It indicated that there is no impact of juvenile wood, sapwood and heartwood ratio, and reaction wood on wood anatomical properties of 8-year-old ramet of D. sissoo. It further indicated that clone raised ramet of 8-year-old D. sissoo showed the characteristics of mature wood. Within tree variations in specific gravity were significant due to height, which may be related to differential sapwood and heartwood ratio in the vertical direction. Different wood elements viz. fiber length, fiber diameter, wall thickness, vessel member length and vessel member diameter showed significant correlations with each other and with specific gravity.