改善喷射沉积耐热铝合金板坯轧制成形性能的研究

喷射沉积Al-8．5Fe-1．3V-1．7Si(8009)耐热铝合金板坯是由基体金属和孔隙、少量颗粒边界的氧化膜组成的，微观组织缺乏良好的冶金结合，直接采用轧制使其致密化产生塑性变形，在工艺上存在极大的难度，轧制时易出现板坯表面裂纹及边裂。本文研究了8009合金的包套轧制、交叉横轧工艺，实验结果表明：采用包套轧制、交叉横轧工艺，有效地改善了喷射沉积板坯的轧制成形性能，成功制备出厚度为0．6～1．0mm的薄板。     

Effects of lunar phase and habitat depth on vertical migrationpatterns of the sergestid shrimp Acetes intermedius

ABSTRACT:   The effects of lunar phase and habitat depth on the verticalmigration patterns of the sergestid shrimp Acetes intermedius wereexamined based on seven field observations in coastal waters offsouth-western Taiwan. The results indicate that the pattern of nocturnalvertical movement of A. intermedius depends on the lunarphase. The shrimp evaded moonlight during the ascending period andthen the moon was used as a trigger for resuming an ascent towardsthe sea surface or descending towards the 10 m water layer.During the descending period, A. intermedius moved rapidlyto the bottom or to a middle water depth at 50–80 mbefore sunrise. However, A. intermedius in waters of deepKaoping Canyon can also perform a slow descending migration thatcoincides with photosynthetically active radiation of 4 µmol/sper m². Because the density of A. intermedius onthe surface layer is affected by moonlight, the lunar phase is oneof the factors affecting the catch rate of large-skimming nets duringthe night in waters off south-western Taiwan.     

农产品供应链事件序列图模型及其应用——以河南小麦为例

建立分析大宗农产品供应链约束条件的事件序列图模型,以小麦供应链为案例进行模型应用和分析,通过测定这条供应链上的速度、成本、资源利用率等性能指标,挖掘出影响供应链整体绩效发展的约束条件,分析影响农产品供应链集成化的障碍。     

坩埚移动式喷射共沉积制取铝基复合材料的技术

提出了坩埚移动式喷射共沉积制备铝基SiC颗粒增强复合材料的装置和方法,并与传统的喷射共沉积装置进行了比较.在SiC颗粒增强相加入方法中,新工艺采用了双环缝复合雾化器和螺杆给料负压引流输送装置,解决了大尺寸、高SiC体积百分比复合材料坯制备技术问题.通过上述装置已经制备出Φ800×1000mm,SiC含量为20wt%,重达1t的铝基复合材料.经后续挤压、锻造加工,制备出了性能优异的6000Al/SiCp,FV0812Al/SiCp,7075Al/SiCp的大尺寸复合材料.讨论了喷射共沉积过程中金属液体对SiC颗粒的捕获机理、喷射共沉积过程中的传热与凝固特征,分析了SiC颗粒的加入对金属液粒凝固的影响.     

Vegetative phase change among sweet corn (Zea mays L.) hybrids varying for reaction to common rust (Puccinia sorghi Schw.)

In maize, timing of vegetative phase change has been implicated in the response to certain pests and environmental stresses. Common rust is the most serious disease of sweet corn in the north central United States. Sweet corn hybrids differing for resistance to common rust were evaluated for vegetative phase change traits. There were significant differences among hybrids for all vegetative phase change traits measured, as well as resistance to common rust. Certain hybrids displayed rapid transition (within two leaves) from juvenile to adult vegetation, while others displayed prolonged transition (within four leaves). There were no significant correlations between vegetative phase change traits and common rust severity among the commercial sweet corn hybrids evaluated in this experiment.     

Numerical Simulation of Elastoplastic Multi-scales Model for Magnesium Alloy Under Tensile Load

In order to investigate the macroscopical mechanical performance of magnesium alloy material containing pore and the mechanism during distorting destructing, an accurate finite element model of magnesium alloy using the multiscales method was developed, and the macroscopic properties of material under the macroscopic tensile load using the developed constitutive model of multi-scales and finite element method was obtained. By analyzing the distortion results of meso-model through the multi-scales method, with macroscopical load increasing, the difference demonstrated on the macroscopic is very small, however, with the increase of the load step, the phenomenon that the ability of plasticity deformation of the meso-models which includes the cuboid pore decreased gradually remarkable and the phenomenon of stress centralized is more severity than the meso-models including cylindrical pore could be obviously observed during the process of deformation on the meso-models.     

Flow Stress Behavior of 3104 Aluminum Alloy

According to different deformation conditions required in working process for manufacturing of 3104 aluminum alloy, the authors design the simulation experiments of hot rolling process at different deformation temperature and strain rates, analyze the relationships of deformation resistance, flow stress and strain rate, deformation temperature when alloy deformation. Based on experimental data analysis, it was concluded that the dominant factors affecting flow stress were the strain rate and deformation temperature, and the two parameters were also important for deforming process control.     

Formation of Zinc Oxide in the Course of Directed Nitriding With Aluminum Zinc Alloy

ZnO is formed in the course of directed nitriding with Al-Zn alloy, and that the effect of zinc and magnesium on the directed nitriding process is big different. The long fibers which diameter are far less than one micrometer, short bar-like and tetrapod-like zinc oxide is obtained. The three important stages of initial growth kinetic of ZnO approving ZnO have growth mechanism of VS, they are stage of accelerating, linear and parabola, are discovered. Experimental results show that the volatilization of zinc play a very important role in the growth of ZnO,the growth of ZnO is controlled by the diffusion of zinc in the Al-Zn alloy , and the morphologies of ZnO is depend on the saturation level of the vapour.     

Learning Causality Diagram Structure Based on Genetic Algorithm

The Causality Diagram theory,which adopted graphical expression of knowledge and direct causality intensity of causality,overcomes some shortages in Belief Network and has evolved into a mixed causality diagram methodology coped with discrete and continuous variable.But it is difficult that the structure of Causality Diagram given by expert.Because the complexity of causality diagram structure goes up exponentially through the number of the vertex's increasing,it is NP-hard problem to find the most possible structure from a set of data.The authors discuss approaches and present Genetic Algorithm,to find the most possible structure from a set of data.Experiment shows the method is effective.