解决CLZ侧风机干燥窑柞木板干燥不均匀的生产性试验

ＣＬＺ侧风机型干燥窑在吉林省以及全国各地旧干燥窑中所占比例颇大，这种干燥窑防腐性能较好，结构简单，投资少，但生产中存在诸多问题：１）终含水率差别大。如白河林业局制材厂８＃窑３８ｍｍ厚的柞木板材干燥 ２９ｄ后有些终含水率仍在 ２８％以上，有些板材终含水率则在４％以下。２）干燥柞木和水曲柳常出现大面积内裂，白河林业局制材厂仅１９９５年就报废了１５窑以上，直接经济损失达２００万元以上。３）表裂、端裂和变形严重。 白河林业局制材厂干燥窑原有生产条件如下：不区分板材厚度堆垛，窑内未设挡风板；材堆侧面与侧墙间…     

8203号杨木材基本性质的测定

本文对８２０３号和木材基本性质进行了测定，其结果：基本密度０．３４５ｇ／ｃｍ＾２；气干密度０．４０ｇ／ｃｍ＾２；干缩系数０．３６；纤维长度１３３７μｍ，长宽比５１；综纤维素含量８０％。８２０３号杨适宜制作各种板材及建筑用材，同时也是较理想的制浆、造纸材种。     

材性改良研究V．美洲黑杨×小叶杨新无性系年轮密度组成性状遗传参数估算

用单色软Ｘ射线木材密度计研究了１１年生美洲黑杨×小叶杨新无性系年轮密度组成性状遗传变异。结果表明，年轮密度组成各性状无性系间存在极显著差异；年轮密度、早材密度、最小密度、最大密度及木材密度梯度等性状遗传力比较高（ｈ２＝０．４１—０．５８），而晚材密度、早晚材密度比及密度变异幅度等性状遗传力比较低（ｈ２＝０．１５—０．２５）；同时各性状遗传力因生长林龄不同而不同。     

黑荆木材及其KP、CTMP的纤维形态研究

研究表明黑荆木材１—３年生密度为０．５９—０．６５ｇ／ｃｍ３，５—１０年生为０．７２ｇ／ｃｍ３；１—７年生木材成分变化不大，纤维素在４５％以上，半纤维素在２５％以下，木素在２１％以下。比较６年生黑荆木材及其ＫＰ、ＣＴＭＰ的纤维形态，纤维长度在０．７６ｍｍ以上的，木材为７２．０４％、Ｋｐ为７２．２２％、ＣＴＭＰ为８２．５８％；平均纤维长度木材为０．８５６ｍｍ、ＫＰ为０．８４５ｍｍ、ＣＴＭＰ为１．１６５ｍｍ；纤维宽度在１２一２４μｍ，木材为９２．６２％、ＫＰ为９２．８６％、ＣＴＭＰ为３４．６３％；平均纤维宽度木材为１５．６μｍ、ＫＰ为１５．８μｍ、ＣＴＭＰ为３０．７μｍ；长宽比木材为５４．９、ＫＰ为５３．３、ＣＴＭＰ为３７．９。     

15种叶树材中切削厚度,刀具前角和木材含水率对切削阻力的影响

１５种阔叶树材切削厚度、刀具前角和木材含水率对切削阻力的影响进行了研究。针叶树材不同树种中此三因素对切削阻力影响的规律，在阔叶树材中相似表现。在气干到充分吸湿阶段中，含水率对切削力影响的趋势在针叶材和阔叶材中有所不同。     

15种阔叶树材中切削厚度、刀具前角和木材含水率对切削阻力的影响

１５种阔叶树材切削厚度、刀具前角和木材含水率对切削阻力的影响进行了研究。针叶树材不同树种中此三因素对切削阻力影响的规律，在阔叶树材中有相似表现。在气干到充分吸湿阶段中，含水率对切削阻力影响的趋势在针叶材和阔叶材中有所不同。     

材性改良研究

用单色软Ｘ射线木材密度计研究了１１年生美洲黑杨×小叶杨新无性系年轮密度组成性状性遗传变异。结果表明，年轮密度组成各性状无性系间存在极显著差异；牢轮密度、早材密度、最小密度、最大密度及木材密度梯度等性状遗传力比较高（ｈ＾２＝０．４１－０．５８），而晚村密度、早晚材密度比及密度变异幅度等性状遗传力比较低（ｈ＾２＝０．１５－０．２５）；同时各性状遗传力因生长林龄不同而不同。     

生材单板挤压脱水的研究

经分析计算，基本密度为０．３６ｇ／ｃｍ￣３的木材，在１２０％的含水率状态下木材中细胞壁物质、水和空气三者的体积比约为１：１：１，因此当该木材体积压榨率达到６６％时，木材中的水分（自由水）几乎将被全部挤出。据此，使用表面有沟槽的几种不同模板对速生树种Ｉ－６９杨和火炬松的生材单板进行了不同压榨车的挤水试验，结果表明：Ｉ－６９杨２．０２ｍｍ生材单板用７０％的压榨率挤压后，含水率显著降低，组内试件间的合水率差异显著缩小；火炬松２．３８ｍｍ和３．３３ｍｍ生材单板，压榨率６０％比４０％的挤水量大、挤后与挤前组内含水率极差比值小，因而达到了降低并均匀生材单板含水车的目的。另外，模板不同也显出不同的挤水效果。     

山杨材性群体变异趋势及个体遗传差异的研究*

在山杨主要分布区随机抽取６个天然群体，每群体随机抽样１５株采集木芯，分析结果表明：群体间及个体间的木材密度和纤维长度差异都极显著。群体平均密度０．４３２ｌｇ／ｃｍ３，极差０．０６６２ｇ／ｃｍ３；平均纤维长度１．０７７５ｍｍ，极差０．２６５０ｍｍ。东北、华北群体的密度呈梯度变异，纤维长度的梯度变异不明显。木材密度群体重复率０．５４１，个体重复率０．４７１；纤维长度重复率分别是０．４７１与０．４１２。不同群体、不同年轮组的密度与纤维长度的个体重复率有所不同。密度、纤维长度等与生长性状呈微弱遗传相关，可以进行材性与生长的同步遗传改良。     

火炬松纸浆林材性变异和优质原料培育期的确定*

１６年生火炬松纸浆材性状研究表明：管胞长度径向呈递增稳定的模式，纵向呈递减变化；其长宽比变异类似于管胞长度的变化；管胞长度变化范围为１．４０３～４．４５６ｍｍ，长宽比为４６．７～７０．１，腔径比为０．７１１～０．７８６，壁腔比为０．３８１～０．４９６。基本密度径向由０．３２４ｇ／ｃｍ３递增到０．４２８ｇ／ｃｍ３；纵向递减，其均值变动于０．３１４～０．４０１ｇ／ｃｍ２；株间木材密度均值与管胞长度两性状不相关。纤维素含量由髓心附近３７．０４％递增到树皮附近４３．９１％，木素、多缩戊糖含量分别由２８．７８％、１４．５９％递减到２５．７４％、１２．０５％，其苯醇抽出物含量变化在２．１２％～８．３８％之间。火炬松木材幼龄期约为１０～１３ａ。基于火炬松木材各树龄材性的变化，结合生长量指标，确定其短周期纸浆林适宜采伐树龄约为１２～１３ａ。     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Decomposition and nutrient loss from prunings of different contour hedgerow species in tea plantations in the sloping highlands of Sri Lanka

Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week⁻¹ for leaves and from 0.0225 to 0.0633 week⁻¹ for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient enrichment capacity and slower decomposition rates which would minimize leaching losses. This revised version was published online in June 2006 with corrections to the Cover Date.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Effects of Seed Weight and Seed Type on Early Seedling Growth of Pinus sylvestris under Harsh and Optimal Conditions

The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions.     

Growth of Phlebiopsis gigantea in wood of seven conifer species

Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered.     

Potential to harness superior nutritional qualities of exotic baobabs if local adaptation can be conferred through grafting

Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral contents and B₁ and B₂ vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B₁ 88 mg 100 g⁻¹, B₂ 187 mg 100 g⁻¹, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations.     

Modelling of adequate pretwist for obtaining straight timber

Abstract

Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.