Prediction of wood stiffness, strength, and shrinkage in juvenile wood of radiata pine

Development of optimal ways to predict juvenile wood stiffness, strength, and stability using wood properties that can be measured with relative ease and low cost is a priority for tree breeding and silviculture. Wood static modulus of elasticity (MOE), modulus of rupture (MOR), radial, tangential, and longitudinal shrinkage (RS, TS, LS), wood density (DEN), sound wave velocity (SWV), spiral grain (SLG), and microfibril angle (MFA) were measured on juvenile wood samples from lower stem sections in two radiata pine test plantations. Variation between inner (rings 1–2 from pith) and outer (rings 3–6 from pith) rings was generally larger than that among trees. MOE and MOR were lower (50%) in inner-rings than in outer-rings. RS and TS were higher (30–50%) for outer-rings than inner-rings, but LS decreased rapidly (>200%) from inner-rings to outer-rings. DEN had a higher correlation with MOR than with MOE, while MFA had a higher correlation with dry wood MOE than with MOR. SLG had higher significant correlation with MOE than with MOR. DEN and MOE had a weak, significant linear relationship with RS and TS, while MOE had a strong negative non-linear relationship with LS. Multiple regressions had a good potential as a method for predicting billet stiffness (R ² > 0.42), but had only a weak potential to predict wood strength and shrinkage (R ² < 0.22). For wood stiffness acoustic velocity measurements seemed to be the most practical, and for wood strength and stability acoustic velocity plus core density seemed to be the most practical measurements for predicting lower stem average in young trees.     

Wood properties and their among-family variations in 10 open-pollinated families of Picea jezoensis

This study aimed to evaluate radial and among-family variations of wood properties in Picea jezoensis. A total of 174 trees were randomly selected from 10 open-pollinated families in a progeny trial for measuring stem diameter, dynamic Young’s modulus of log (DMOE_log), annual ring width (ARW), air-dry density (AD), modulus of elasticity (MOE), and modulus of rupture (MOR). Mean values of DMOE_log, AD, MOE, and MOR were 9.60 GPa, 0.41 g/cm³, 9.44 GPa, and 76.6 MPa, respectively. Significant differences among families were observed in all properties. F values obtained by analyzing variance in wood properties were higher than those generally observed in growth traits. In addition, F values in wood properties remained relatively higher from the 1st to 25th annual ring from the pith, although F value in ARW rapidly decreased with each increase in annual ring number. These results indicate that genetic factors largely contributed to the variance in wood properties compared with the growth traits.     

The variation of microfibril angle in South African grown Pinus patula and its influence on the stiffness of structural lumber

Reduction in the rotation ages of softwood saw-log plantations in South Africa is causing increased proportions of low stiffness sawn lumber at final harvest. It has been shown for some species that the microfibril angle (MFA) of the S2 layer of tracheids is strongly related to the modulus of elasticity (MOE) of wood, even more so than wood density, especially in wood formed during juvenile growth. The objectives of this study were to describe the variation in MFA in young Pinus patula trees and to determine the relationship between MFA and the dynamic MOE of sawn P. patula lumber. Thirty 16- to 20-year-old trees from six compartments from the Mpumalanga escarpment were processed into discs and lumber. The MFA, density and ring width were measured at two height levels using Silviscan 3. The average annual ring MFA varied between 7° and 29°; the pattern of variation depended mainly on height level and the ring number from the pith. The MFA in P. patula followed the same within-tree variation trends as in New Zealand-grown Pinus radiata but the average MFA was lower in absolute terms and differences between height levels were less pronounced. The MFA and density exhibited highly significant Pearson correlations of 0.73 and 0.70, respectively, with board dynamic MOE. A multiple regression model, which included MFA, density and ring width, explained 71% of the variation in the dynamic MOE of boards. A sensitivity analysis on the model showed that MFA and density had approximately similar influences on predicting the dynamic MOE of Pinus patula boards.     

Static bending properties of Finnish birch wood

The purpose of this study was to determine the modulus of elasticity (MOE) and the modulus of rupture (MOR) in the radial bending test for small, clear specimens of Finnish birch (Betula pendula Roth and B. pubescens Ehrh) wood originating from mature trees. The dependency of MOE and MOR on the specific gravity of birch wood was studied, and the relationship between MOE and MOR was modelled at the different heights and at the different distances from the pith of the tree. For B. pendula, the mean values for MOE and MOR were 14.5 GPa and 114 MPa, whereas B. pubescens had means of 13.2 GPa and 104 MPa, respectively. At the corresponding specific gravity, the bending stiffness and strength values did not differ between the two species. The results indicated a linear relationship between the MOE and MOR, irrespective of the birch species or the within-stem location. Both MOE and MOR increased clearly from the pith towards the surface of the tree and decreased slightly from the base to the top of the tree. It seems that if products with as high stiffness and bending strength as possible are wanted, sorting of raw materials into different grades according to their within-tree origin can be of value.     

Variation in wood properties among five full-sib families of Norway spruce (Picea abies)

Genetic- and environmental variation and correlation patterns were characterized for modulus of elasticity (MOE), modulus of rupture (MOR) and related wood traits: latewood proportion, wood density, spiral grain, microfibril angle and lignin content in five full-sib families of Norway spruce. The families were evaluated on the basis of clearwood specimens from the juvenile -mature wood transition zone of 93 sampled trees at age 30 year from seed. Family-means varied significantly (p < 0.05) for all wood traits studied except lignin content. MOE varied between 7.9–14.1 GPa among trees and 9.4–11.0 GPa among families. MOR varied between 47–87 MPa among trees and 61–71 MPa among families. Families remained significantly different in an analysis of specific MOE (MOE/density) and MOR (MOR/density). Hence, solely relying on wood density as a wood quality trait in tree breeding would not fully yield the potential genetic gain for MOE and MOR. Correlations between wood structural traits and specific MOE and MOR are presented and discussed.     

Efficiency of early selection for rotation-aged wood quality traits in radiata pine

A total of 360 bark-to-bark-through-pith wood strips were sampled at breast height from 180 trees in 30 open-pollinated families from two rotation-aged genetic trials to study inheritance, age-age genetic correlation, and early selection efficiency for wood quality traits in radiata pine. Wood strips were evaluated by SilviScan® and annual pattern and genetic parameters for growth, wood density, microfibril angle (MFA), and stiffness (modulus of elasticity: MOE) for early to rotation ages were estimated. Annual ring growth was the largest between ages 2–5 years from pith, and decreased linearly to ages 9–10. Annual growth was similar and consistent at later ages. Wood density was the lowest near the pith, increased steadily to age 11–15 years, then was relatively stable after these ages. MFA was highest (35°) near the pith and reduced to about 10° at age 10–15 years. MFA was almost unchanged at later ages. MOE increased from about 2.5 GPa near the pith to about 20 GPa at ages 11–15 years. MOE was relatively unchanged at later ages. Wood density and MOE were inversely related to MFA. Heritability increased from zero near the pith and stabilised at ages 4 or 5 for all four growth and wood quality traits (DBH, density, MFA and MOE). Across age classes, heritability was the highest for area-weighted density and MFA, lowest for DBH, and intermediate for MOE. Age-age genetic correlations were high for the four traits studied. The genetic correlation reached 0.8 after age 7 for most traits. Early selection for density, MFA and MOE were very effective. Selection at age 7–8 has similar effectiveness as selection conducted at rotation age for MFA and MOE and at least 80% effective for wood density.     

Growth and wood quality of sugi (Cryptomeria japonica) planted in Akita prefecture (II). Juvenile/mature wood determination of aged trees

Variations of certain anatomical and mechanical indices within tree stems of aged sugi (Cryptomeria japonica) trees planted in Akita prefecture were studied. The determination of the juvenile/mature wood boundary was also discussed, and the effects of wood structure on mechanical properties were investigated. On the basis of radial and vertical variation of the anatomical and mechanical indices, modulus of elasticity (MOE)/ shear modulus (G) was chosen as the index for determining the juvenile/mature wood boundary. The increase rates of MOE/G at the points of 1%, 2%, and 3% were discussed. It was found that for aged trees, all three points were thought to be effective for dividing juvenile and mature wood. However, for younger trees, the point of 2% was recommended, which was mostly consistent with the result obtained by the increase rate of 1% for tracheid length (TL). Among mechanical properties, the MOE showed more significant juvenile/mature wood differences than did modulus of rupture (MOR) and . By correlation analysis, it was suggested that microfibril angle largely contributed to the indices of MOE and G, and specific gravity largely contributed to the indices of MOR and .Part of this report was presented at the 53rd Annual Meeting of the Japan Wood Research Society, Fukuoka, March 2003     

Fresh-wood bending: linking the mechanical and growth properties of a Norway spruce stem

To provide data and methods for analyzing stem mechanics, we investigated bending, density and growth characteristics of 207 specimens of fresh wood from different heights and radial positions of the stem of one mature Norway spruce (Picea abies L. Karst.) tree. From the shape of each stress-strain curve, which was calculated from bending tests that accounted for shear deformation, we determined the modulus of elasticity (MOE), the modulus of rupture (MOR), the completeness of the material, an idealized stress-strain curve and the work involved in bending. In general, all mechanical properties increased with distance from the pith, with values in the ranges of 5.7-18 GPa for MOE, 23-90 MPa for MOR and 370-630 and 430-1100 kg m(-3) for dry and fresh wood densities, respectively. The first three properties generally decreased with stem height, whereas fresh wood density increased. Multiple regression equations were calculated, relating MOR, MOE and dry wood density to growth properties. We applied these equations to the growth of the entire stem and considered the annual rings as superimposed cylindrical shells, resulting in stem-section values of MOE, MOR and dry and fresh densities as a function of stem height and cambial age. The standing tree exhibits an inner stem structure that is well designed for bending, especially at a mature stage.     

Genetic variation and relationships to growth traits for microfibril angle,wood density and modulus of elasticity in a Picea abies clonal trial in southern Sweden

Abstract

Genetic variation in wood density, microfibril angle (MFA), wood stiffness (MOE), height, diameter and volume was investigated in a 26-year-old Norway spruce [(Picea abies (L.) Karst.] clonal trial in southern Sweden. Wood quality measurements were performed on 10 mm increment cores using SilviScan. For MFA, mean values of annual rings showed the highest value (30°) at ring 2 counting from the pith, followed by a steep decrease and a gradual stabilization around ring 12 at approximately 14°. MOE showed a monotonic increase from 5 GPa to 14 GPa when moving from pith to bark. High broad-sense heritability values were found for wood density (0.48), MFA (0.41) and MOE (0.50). All growth traits displayed heritability values of similar magnitudes as reported in earlier studies. The generally high age–age correlations between different sections of the wood cores suggested that early selection for wood quality traits would be successful. Owing to unfavorable genetic correlations between volume and MOE, the correlated response indicated that selection for volume only at age 10 would result in a 0.27% decrease in weighted MOE at age 26 for every 1% increase in volume.     

Within-stem variations in mechanical properties of <Emphasis Type="Italic">Melia azedarach</Emphasis> planted in northern Vietnam

Within-stem variations in the mechanical properties of 17–19-year-old Melia azedarach planted in two sites in northern Vietnam were examined by destructive and nondestructive methods. Wood samples were collected from 10, 50, and 90% of the radial length from pith on both sides (North and South) at 0.3, 1.3, 3.3, 5.3, and 7.3 m heights above the ground. The mean values in whole trees of wood density (WD), modulus of rupture (MOR), modulus of elasticity (MOE), and dynamic modulus of elasticity (E_d) at 12% moisture content were 0.51 g/cm³, 78.58 MPa, 9.26 GPa, and 10.93 GPa, respectively. Within the stem, the radial position was a highly (p?<?0.001) significant source of variation in mechanical properties. MOR, MOE, and E_d increased from pith to bark. WD had a strong positive linear relationship with both MOR (r?=?0.85, p?<?0.001) and MOE (r?=?0.73, p?<?0.001). This suggests that it is potentially possible to improve mechanical properties through controlling WD. MOR had also a strong linear relationship with E_d (r?=?0.84, p?<?0.001). This indicates that E_d is a good indicator to predicting the strength of wood if the density of measured element is known. Besides, the stress wave method used in this study provides relatively accurate information for determining the stiffness of Melia azedarach planted in northern Vietnam.     

Microfibril angle and density of hinoki (Chamaecyparis obtusa) trees in 15 half-sib families in a progeny test stand in Kyushu, Japan

It was previously believed in Japan that the wood qualities of hinoki (Chamaecyparis obtusa) were superior to sugi (Cryptomeria japonica). However, few studies of wood properties such as MFA (microfibril angle of S₂ layer in secondary wall of tracheid) have been completed for hinoki. Some reports have found that hinoki plus tree families have similar mechanical properties to sugi. Here we report the characteristics of MFA and density of hinoki half-sib families in a progeny test stand. There were significant differences in MFA and density between families. The wood properties of two families, Nakatsu 3 and Kanzaki 5, are stable in radial pattern and suitable for structural use. Early selection of hinoki families by MFA and density may be difficult. Effects of MFA and density on E _d (dynamic modulus of elasticity) of logs differed between families. The effects of growth rate on MFA and density differed between families and also between juvenile and mature wood. The faster growth rate in Nakatsu 3 appeared to improve wood properties and increase E _d of logs, although in many other families, faster growth rate had negative effects on desirable wood properties for structural use.     

Static bending strength performances of cross-laminated woods made with five species

Thirty types of three-ply parallel- and cross-laminated woods were prepared from five species, and their static bending strength performance were investigated. The modulus of elasticity (MOE), proportional limit stress, and modulus of rupture (MOR) perpendicular to the grain were increased by cross-laminating, and the extent of the increase increased with decreasing density of the species. The measured values of MOE parallel and perpendi-cular to the grain of parallel-laminated woods and perpendicular to the grain of face laminae of cross-laminated woods were approximately equal to those calculated from true MOEs of individual laminae. However, the MOE parallel to the grain of face laminae of cross-laminated woods was much lower than the calculated MOE owing to the effect of the deflection caused by shear force on the MOE. The percentage of deflection caused by shear force versus total deflection (Y _s) showed high values, from 16.1% (buna) to 40.5% (sugi), and it decreased linearly with increasing shear modulus in the cross section of the core. In addition, there was an extremely high positive correlation between the MOR and the measured MOE parallel to the grain of face laminae of cross-laminated woods. The MOR was also highly dependent on the shear modulus in cross section of the core.Part of this paper was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, April 2000     

Stem damage of lodgepole pine clonal cuttings in relation to wood and fiber traits,acoustic velocity,and spiral grain

Eight clones from a 16-year-old field trial of clonal cuttings of lodgepole pine (Pinus contorta Dougl. ex Loud. var. latifolia Engelm.) were analyzed for growth, growth pattern, and stem damage in the field. In addition, wood and fiber traits (acoustic velocity [AcVel] and spiral grain) were analyzed and wood density, microfibril angle, modulus of elasticity, and radial fiber diameter (FibDR) determined from SilviScan analyzes. Two clones with considerably more bent, broken, and leaning stems differed from the other clones in terms of microfibril angle and modulus of elasticity (MOE) in the outermost annual rings. FibDR and, to some extent, MOE in the outermost annual rings were negatively correlated with the frequency of bent, leaning, or broken stems, while microfibril angle (MFA) was positively correlated. AcVel was negatively correlated with both MFA and the frequency of bent, broken, and leaning stems. We conclude that AcVel could be used as an effective tool to predict severe stem damage and determine stem strength in the field instead of using costly lab-based SilviScan measurements of microfibril angle. If developed further, this approach could be used for large-scale screening of progeny tests when selecting for stem strength.     

人工林杉木和杨树木材物理力学性质的株内变异研究

按照中国国家标准研究杉木和I-214杨树木材的抗弯弹性模量、抗弯强度、顺纹抗压强度和密度,同时按照日本国家标准研究2个树种的顺纹抗剪强度.结果表明:杉木的抗弯强度、顺纹抗压强度和密度由胸高直径处向上呈波浪形增加,抗弯弹性模量则稳定降低,但不同高度间杉木的物理力学性质没有显著差异;近树皮处木材的物理力学性质高于近髓心处木材,并有极显著差异.对于I-214杨树,只有抗弯弹性模量从髓心到树皮逐渐增加,其他的物理力学性质,最小值在从髓心到树皮的过渡区,最大值在近树皮处,从髓心到树皮,杨树的物理力学性质有极显著的差异.杉木和杨树的径面顺纹抗剪强度从髓心到树皮有极显著差异,并且近树皮的高于近髓心的木材,而弦面顺纹抗剪强度从髓心到树皮没有显著差异.木材密度与力学性质有很好的线性相关关系,木材密度是一个很好的力学强度的预测手段.     

Performance of samama (Anthocephalus macrophyllus) LVL based on veneer thickness,juvenile proportion and lay-up

ABSTRACT

A study to determine the quality of laminated veneer lumber (LVL) from samama wood (Anthocephalus macrophyllus) was carried out. Samama is a fast-growing endemic wood in eastern Indonesia. Factorial of three factors in RAL design was used to investigate the influence of veneer thickness, juvenile proportion and veneer lay-up to the quality of the resulted samama LVL. The veneer thicknesses were 1.5 and 3.0?mm. Juvenile proportions were arranged in five levels, which were 100% of juvenile veneer, 100% of mature veneer and combination of both juvenile and mature with juvenile proportion of 14%, 43% and 71%. Two veneer lay-up used in this study were loose side met loose side and tight side met loose side. The result of the study showed various specific gravity of LVL by different proportions of juvenile. This factor also affected the other physical traits. Shear strength of the LVL was equal to the solid wood, yet MOE and MOR were affected by juvenile proportion and veneer lay-up. LVL developed from 100% of mature veneer exhibited the highest MOE and MOR, yet no significant difference was noted in MOE and MOR between LVL 100% of juvenile and other tested juvenile proportions.     

红松幼龄材与成熟材力学性质的差异

本文研究了人工林和天然林红松幼龄材与成熟材力学性质的差异.结果显示,成熟材的所有力学性质均高于幼龄材.幼龄材与成熟材的抗弯弹性模量差异在人工林红松中达0.01水平显著,天然林红松也达到0.01水平显著;人工林红松抗弯强度和弦向横纹抗压强度差异达0.05水平显著.抗弯强度、顺纹抗压强度、横切面硬度和弦向横纹抗压强度4项指标的差异达0.05水平显著.     

Genetic variation in wood stiffness and strength properties of hybrid larch (Larix gmelinii var. japonica × L. kaempferi)

Genetic parameters for wood stiffness and strength properties were estimated in a 29-year-old hybrid larch stand (Larix gmelinii var. japonica × Larix kaempferi). The study included 19 full-sib larch families from Hokkaido, northern Japan. Implications of these genetic parameters in wood quality improvement are subsequently discussed. Traits included in the analyses were the dynamic modulus of elasticity of green logs (E _log), the modulus of elasticity (MOE), the modulus of rupture (MOR), compression strength parallel to the grain (CS) in small clear specimens, wood density (DEN), and diameter at breast height (DBH). DEN had the lowest coefficients of variation and MOE the highest. The narrow-sense heritability estimates of E _log, MOE, MOR, and CS were 0.61, 0.44, 0.60, and 0.43, respectively, and those of DEN and all mechanical properties increased from an inner to outer position within the stem. E _log and DEN had high positive phenotypic (0.52–0.83) and genetic (0.70–0.92) correlations with MOE, MOR, and CS. The mechanical properties of the inner position of the stem had rather high phenotypic and genetic correlations with those of the outer position and overall mean. The predicted gains in wood stiffness (E _log and MOE) were higher than those of the strength properties (MOR and CS). The predicted correlated responses in MOE, MOR, and CS when selecting for E _log and DEN were 72.6%–97.8% of a gain achievable from direct selection of these traits. DBH showed an insignificant correlation with all mechanical properties, although selection of this trait had a slightly negative effect on the mechanical properties.     

Influence of initial planting spacing and genotype on microfibril angle,wood density,fibre properties and modulus of elasticity in Pinus radiata D. Don corewood

Pinus radiata D. Don trees from six clones, grown at initial spacings of 2500 stems ha⁻¹ and 833 stems ha⁻¹ were destructively harvested. For these trees wood properties were measured on radial slices sampled at a height of 1.4 m above the ground. Relative to wide spacing, close initial stand spacing significantly reduced microfibril angle (MFA) and ring width and significantly increased dynamic modulus of elasticity (MOE), fibre length, latewood percentage and cell wall thickness. Density and fibre width were not significantly different between spacing treatments. Examination of the influence of genetic population on wood properties indicated that genotype significantly influenced MFA, MOE and ring width. The key wood properties MFA, MOE and fibre length were regressed against tree diameter, height and stem slenderness. All three wood properties were most strongly correlated with stem slenderness. Multiple regression models developed for MFA, MOE and ring width accounted for respectively 62%, 81% and 58% of the variation in these variables. The following changes occurred in sampled properties with increasing ring number: MFA and ring width declined markedly; MOE and fibre length increased markedly; latewood percentage and cell wall thickness increased slightly; and density and fibre width did not show any radial trend.     

Structural mechanism and effect of hole compressibility on mechanical strength of MFLB

We have studied the structural mechanism of micron flaky wood fiber light density board (MFLB), of which voids are an important structural characteristic. A new parameter called hole compressibility (η) was added to study the characteristics of MFLB further, in order to produce various levels of hole compressibility. A set of hot pressures was applied, and uniform parts at cross-sections of MFLB were selected to study the effects of hole compressibility on the modulus of elasticity (MOE) and modulus of rupture (MOR) of MFLB by microscopic analyses. The results showed that MFLB (0.3 g/cm³ in density) processed at various hot pressures (from 1.6 to 2.2 MPa) all meet the norms of the Japan Light Particleboard Industrial Standard JISA 5908, where η ⩽ 0 ranging from −0.0487 to −0.068. The critical value of hole compressibility at which the strength began to decrease was also obtained. We compared the void distribution, size and shape at different void contents and hole compressibility and discussed the effects of hole compressibility on MOE and MOR of MFLB as well. To a certain density of raw material and micro-fiber of a certain thickness, the strength of MFLB can be decreased with an increase in hole compressibility. When the hole compressibility of MLFB exceeds a certain critical value, loading at a lower level will decrease MOR and MOE of MFLB considerably. __________ Translated from Scientia Silvae Sinicae, 2007, 43(6): 123–127 [译自: 林业科学]     

蔗髓含量对蔗渣碎料板性能的影响研究

研究了蔗髓含量（质量分数）分别在10%、20%、30%、40%4种不同情况下蔗渣碎料板的密度、静曲强度、弹性模量、内结合强度、吸水厚度膨胀率和板面握钉力等物理力学性能的变化规律.结果发现，随蔗髓含量的增加，板材的密度增加，弹性模量和板面握钉力下降；在蔗髓含量低于20%以下时，蔗髓的存在对板材的静曲强度无明显影响，而随蔗髓含量增加，吸水厚度膨胀率影响显著上升；在蔗髓含量高于20%以上时，蔗髓的含量增加使板材静曲强度明显下降，而对吸水厚度膨胀率无影响；蔗髓的含量对板材的内结合强度影响不明显.