杨木/狼尾草复合中密度纤维板工艺研究

研究了速生杨木/狼尾草复合中密度纤维板的工艺.试验结果表明:利用速生杨木和狼尾草制造脲醛树脂中密度纤维板是可行的,产品性能可以超过国家中密度纤维板标准的要求.该产品生产的较佳工艺为板材密度0.85 g/cm3,热压温度170℃,热压时间20 s/mm(板厚).     

蒸爆法棉秆无胶纤维板热压工艺初探

以棉秆为原料,经过蒸爆解纤处理后热压制成无胶纤维板.研究了密度为0.85g/cm3、板厚为4mm的无胶纤维板热压工艺.结果表明:在试验范围内较优的热压工艺为:板坯含水率12%、热压温度210℃、热压时间60s/mm.     

密度及热压工艺对竹篾层积材性能的影响

为解决冷压工艺生产周期长和能量消耗大的问题,采用梯度降压的热压法制备竹篾层积材,并分析工艺参数对其性能的影响.结果表明:热压温度对板材的弹性模量、静曲强度、吸水厚度膨胀率和水平剪切强度影响显著;热压时间和密度对板材的吸水厚度膨胀率影响较大.在密度1.0 g/cm3、热压时间1.5 min/mm、温度145～155℃的条件下,板材性能达到LY/T 1072-2002《竹篾层积材》和GB/T 20241-2006《单板层积材》的要求.     

室外型杨木中密度纤维板的制造工艺

以正交试验为基本方法 ,以统计分析为主要手段 ,对室外型杨木中密度纤维板的制造工艺进行了研究。通过验证、跟踪试验 ,结果表明 :以杨木为原材料制造室外型中密度纤维板是可行的 ;在施胶量 12 %、板密度 0 .82 g/ cm3、热压温度 180℃、热压时间 7min条件下 ,试验室制 9mm厚板材的所有性能指标均达到国家标准要求     

杨木单板条层积材的制备工艺及性能评价

为了更好地利用单板加工剩余物,采用三聚氰胺改性脲醛树脂胶制备杨木单板条层积材(PSL),探讨涂胶量、热压工艺及板材密度等工艺因子对板材性能的影响。在本试验条件下,较优工艺参数为:涂胶量(双面)300g/m~2、热压温度130℃、热压时间75 s/mm、板材密度0.60 g/cm~3,制备的PSL物理力学性能优良,甲醛释放量低于GB 18580-2001中E1限量值(≤1.5 mg/L),可用作室内装饰装修用材。     

改性豆基蛋白胶杨木刨花板的制造工艺

探讨利用改性豆基蛋白胶压制杨木刨花板的工艺,分析热压温度、热压时间、施胶量和防水剂加入量对杨木刨花板性能的影响,提出厚12 mm、密度0.70 g/cm3杨木刨花板的最佳工艺条件为:热压温度170℃,热压时间14min,施胶量10%,防水剂加入量1.4%。在此条件压制的板材的性能超过GB/T 4897.4-2003的要求。     

不同工艺参数对UF工业大麻秆刨花板性能的影响研究

工业大麻秆是一种优质的轻质非木质原料,利用脲醛树脂为胶黏剂可以制备出性能优良的刨花板产品.笔者主要分析不同的工艺参数,包括密度、热压时间、热压温度和施胶量对板材性能的影响.研究结果表明,密度和施胶量对板材性能的影响要比热压温度和热压时间明显,随着板材密度、热压温度和热压时间的增加,板材的力学性能大多先增加后减小;而随着施胶量的增加,板材的力学性能呈增加趋势.在目标密度0.55 g/cm3,施胶量10％,热压温度130℃或170℃条件下,板材的力学性能可达到国标普通刨花板的标准要求;当目标密度等于或高于0.65 g/cm3、施胶量等于或高于12％、热压温度在140～ 160℃、热压时间在20 ～ 45s/mm之间时,除TS外,板材的其他力学性能可达到国标室内装饰和家具用材的标准要求,并可与相同工艺条件下,目标密度为0.75 g/cm3的木质刨花板的各项性能相媲美.可见,工业大麻秆是一种优质的非木质原料,利用该原料在低温条件下制备低密度的刨花板是可行的.     

连续平压法生产低密度纤维板的工艺研究

在连续平压法生产线上进行制备低密度纤维板试验,分别探讨板材密度、二次加压区热压温度对板材主要力学性能的影响,并通过正交试验分析板材密度、二次加压区热压压力、施胶量、钢带运行速度4个因素对低密度纤维板主要性能的影响,结果表明:各因素对板的内结合强度与静曲强度影响大小顺序为:板材密度、二次加压区热压压力、施胶量、热压时间;其中,密度对板材性能的影响极显著。采用二次加压区热压压力0.4 MPa,施胶量16%,热压时间10.5 s·mm-1,二次加压区热压温度190℃的工艺组合采用连续平压法生产厚度18 mm的低密度纤维板,密度为563.56 kg·m-3、内结合强度为0.46 MPa、静曲强度为24.5 MPa、弹性模量为2356 MPa、吸水厚度膨胀率为10.8%,达到GB/T 11718—2009中干燥状态下使用的普通型中密度纤维板性能要求。     

麦秸/木材三层结构无机刨花板的制备工艺

以麦秸、木材碎料和无机胶黏剂制备麦秸/木材三层结构刨花板。研究麦秸与木材配比、板材密度、热压时间和温度对板材性能的影响。结果表明:随麦秸配比增加,板材抗弯性能降低,内结合强度增大,吸水厚度膨胀率(TS)减小;随密度增加和热压时间延长,板材力学性能增大,TS降低;随热压温度升高,板材力学性能先增大后减小,TS呈相反趋势。优化制板工艺为:碎料配比5:5,密度1.2g/cm~3,热压时间30min,温度100℃。     

棉秆中密度纤维板工艺技术的研究

探讨以棉秆为原料生产中密度纤维板的主要生产工艺参数.试验结果表明,在板材密度0.7 g/cm3、施胶量12%、防水剂1.5%、热压温度180℃、热压时间15 s/mm的最佳工艺条件下,棉秆中密度纤维板的各项力学性能均超过国家标准要求,但24 h吸水厚度膨胀率未达标,可能与棉秆原料自身特点有关.     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Decomposition and nutrient loss from prunings of different contour hedgerow species in tea plantations in the sloping highlands of Sri Lanka

Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week⁻¹ for leaves and from 0.0225 to 0.0633 week⁻¹ for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient enrichment capacity and slower decomposition rates which would minimize leaching losses. This revised version was published online in June 2006 with corrections to the Cover Date.     

Effects of Seed Weight and Seed Type on Early Seedling Growth of Pinus sylvestris under Harsh and Optimal Conditions

The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions.     

Potential to harness superior nutritional qualities of exotic baobabs if local adaptation can be conferred through grafting

Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral contents and B₁ and B₂ vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B₁ 88 mg 100 g⁻¹, B₂ 187 mg 100 g⁻¹, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations.     

Modelling of adequate pretwist for obtaining straight timber

Abstract

Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Growth of Phlebiopsis gigantea in wood of seven conifer species

Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered.