蜗壳式离心泵外特性仿真与实验研究

为探索不同仿真方法的适用性,对ns=157的单级蜗壳离心泵不同工况的扬程和效率进行定常和非定常计算,并分别分析了定常计算时不同叶片夹角及非定常计算时不同时间步长的影响,通过与实验对比,得到的主要结论有:定常计算仅适用于额定工况外特性仿真,其扬程和效率计算误差分别为4.9%和2.9%,而定常多相位的计算误差分别为7.1%和3.2%;非定常仿真计算时,以4°为时间步长,并间隔20°保存一次计算数据,较好地预测出扬程曲线走势,额定工况扬程和效率计算误差约1.1%和1.8%,但小流量和大流量区间扬程计算误差达到10%左右。因此在水力优化设计时,若只关注高效点位置及其扬程和效率,可采用定常计算,若还关注扬程曲线走势,则应采用非定常计算。     

Experimental investigation on the transport of different fish species in a jet fish pump

A jet fish pump with a throat of ø60 mm was designed to study its performance in the transport of different fish species and the physiological changes in fish thereafter. Experiments were conducted to investigate the fish transport rate and energy required to transport each ton of fish when transporting Carassius auratus, commonly known as the Chinese goldfish, Megalobrama amblycephala, or Wuchang bream, and Ctenopharyngodon idella, the grass carp. Fish were examined for external injuries as well as for several important enzymes and hormones which are indicators of tissue injury and stress. The results showed that the transport rate for all three species of fish rose dramatically with an increase in the primary stream rate. In this experiment, the transport rates of C. auratus, M. amblycephala and C. idella reached 2357 ± 37.2 kg ∙ h⁻¹, 2888 ± 41.6 kg ∙ h⁻¹, and 2060 ± 40.2 kg ∙ h⁻¹, respectively. However, both injury rate and energy required to transport each ton of fish increased no matter whether the primary stream rate was too low or too high. Considering both transport rate and injury rate, the mean primary stream rate of 80 m³ ∙ h⁻¹ was determined to be the optimal operating condition in this experiment. Fish were stressed and most likely some of their organs were damaged. However, most physiological indexes almost fully recovered after several hours.     

Engineered-airlift pumps for aquaculture applications using multiphase flow analysis

Currently, very few aquaculture operations are employing airlift pump technology for water recirculation, aeration, and waste removal. This is likely due to the poor design and lower efficiency of traditional airlift design, the limited amount of research effort that has been invested in improving performance capabilities of air lift pumps and the general lack of awareness of the industry about the inherent advantages of airlift systems. A new efficient airlift pump is hydrodynamically designed by incorporating the Volume of Fluid (VOF) multi-phase model along with the K-ε turbulence model utilizing Computational Fluid Dynamics (CFD) tools. The pump is designed to offer a substantial reduction in total energy usage as well as an improved quality of the culture products in order to make it attractive to aquaculture industry. In this study, both numerical and experimental investigations were carried out for airlift systems operating under two different submergence ratios of 50% and 90% in a lab setting using 2.54 cm diameter pumps. Also, the performance of a large-scale pumps of 10.16 cm diameters were also tested in an aquaculture raceway to determine its effect on the operation. The numerical results were found to be in agreement with the experiments within ±20% which is considered very reasonable for multiphase flow analysis. The present study was found to present a great tool for modelling the airlift pump performance, and potentially proposing new designs.     

叶轮出口边对双蜗壳泵压力脉动的影响

泵的叶轮扫掠蜗壳隔舌时产生的压力脉动是引起船用泵振动噪声的原因之一.为尽可能弱化这一影响,分别设计了叶片出口边与前后盖板基本面垂直和倾斜的2种不同形式叶轮,将其配置在相同的双蜗壳中,通过数值计算与样机试验相结合的手段,对蜗壳内9个不同位置的压力脉动情况进行对比分析.结果表明:出口边倾斜的叶轮相比于出口边垂直的叶轮可明显改善蜗壳内次脉动的“驼峰”现象,且可以进一步降低隔舌处主波动的压力峰值;对蜗壳内2个隔舌稍前的位置,出口边倾斜的叶轮反而会使得该点的压力系数幅值明显增大,且该点主波动的周期数发生改变;2种叶轮出口边的不同形式对蜗壳出口位置的压力脉动的影响基本相同;采用出口边倾斜叶轮对改善因叶轮与隔舌间的液流压力脉动是可行的.     

泡沫比例混合器在液下喷射灭火系统中的应用

提出了环泵泡沫比例混合器和泡沫压力比例混合器在相应灭火系统中的应用、安装和操作中应注意的问题，对两种泡沫比例混合器组成的系统进行了对比，认为环泵比例混合泡沫灭火系统采用正压进水，可以克服负压进水方式存在的缺陷，比较适合油库火灾的扑救；压力比例混合泡沫灭火系统灵活性、匹配性较差，适用于泡沫混合液流量相对不变的火灾扑救。     

迷宫螺旋槽的选取研究

以提高迷宫螺旋泵的扬程、流量、效率、汽蚀等性能参数为目标,给出不同使用条件下螺旋槽形状与几何参数的选取。     

冷却水循环用离心泵汽蚀的原因与防止方法探讨

通过对冷却水循环用离心泵产生汽蚀的因素进行分析，提出了防止汽蚀产生的技术措施，经生产应用效果良好。     

机械化奶站真空系统的设计

阐述了机械化奶站真空系统的组成、真空泵的工作原理、真空系统设计中应遵循的原则及设计过程中的注意事项,提出了设计机械化挤奶站真空系统的方法。     

步进电机扭矩测量试验台系统的设计

专用电机扭矩测量仪器精度高，但价格昂贵，操作复杂，长时间使用会出现误差。步进电机扭矩测量试验台系统采用单相交流电机作负载，使用标准扭矩仪对该系统进行标定来对待测调速电机进行扭矩测量。为此，介绍了一种电机扭矩测量系统的构成与工作原理。该系统以单片机为核心，组成扭矩测量与显示系统，可以较好地实现电机扭矩在线测量，具有较好的经济效益。     

污水污物潜水旋流泵性能及设计方法试验研究

对影响潜水旋流泵性能的6个主要过流件几何参数进行了试验研究，初步掌握了旋流泵叶轮及泵体主要几何尺寸对性能影响的规律。在分析16种优秀水力模型的基础上，计算出叶轮D2及b2函数回归方程式，并用设计实例进行检验，样机效率比国内外同类产品提高3％左右。