Reproductive traits of the Ryukyu long-furred rat (Diplothrix legata) on Okinawa-jima Island

The Ryukyu long-furred rat, Diplothrix legata, is a large rodent distributed only on Amami-ohshima Island, Tokuno-shima Island and Okinawa-jima Island, Japan. This animal is endangered as a result of deforestation, predation by introduced carnivores and mortality caused by vehicles. We performed theriogenological examinations of 32 male and 25 female Ryukyu long-furred rats carcasses collected from wild populations on northern Okinawa-jima Island from December 2005 to September 2013. Adult males had remarkably large preputial glands. Seminiferous diameter of adult was significantly small (136 ± 28 µm, n=8) from April to August. Numerous spermatozoa were observed from September through February, and seminiferous diameter was significantly large (216 ± 27 µm, n=12) during this time in adults; testes length changed in a similar pattern. These findings indicate that the mating season may occur from September through February. Size (body length) at sexual maturity was estimated to be >560 mm in both sexes. From observation of corpora lutea and placental scars, litter size was estimated to range from 2 to 12 (average=6, n=4). These results provide fundamental knowledge that will be beneficial for in situ and ex situ conservation of this rare species.     

Vitamin D Status in Different Stages of Disease Severity in Dogs with Chronic Valvular Heart Disease

Background

In humans with heart disease, vitamin D deficiency is associated with disease progression and a poor prognosis. A recent study showed that serum 25‐hydroxyvitamin D [25(OH)D] concentration, the hallmark of vitamin D status, was lower in dogs with heart failure than in normal dogs, and a low concentration was associated with poor outcome in dogs with heart failure.

Objectives

To elucidate the vitamin D status of dogs with chronic valvular heart disease (CVHD) at different stages of disease severity.

Animals

Forty‐three client‐owned dogs with CVHD.

Methods

In this cross‐sectional study, dogs were divided into 3 groups (14 dogs in Stage B1, 17 dogs in Stage B2, and 12 dogs in Stage C/D) according to ACVIM guidelines. Dogs underwent clinical examination including echocardiography. Serum 25(OH)D concentrations were measured in each dog.

Results

Serum 25(OH)D concentration was significantly lower in Stage B2 (median, 33.2 nmol/L; range, 4.9–171.7 nmol/L) and C/D (13.1 nmol/L; 4.9–58.1 nmol/L) than in Stage B1 (52.5 nmol/L; 33.5–178.0 nmol/L) and was not significantly different between Stage B2 and Stage C/D. Among clinical variables, there were significant negative correlations between 25(OH)D concentration and both left atrial‐to‐aortic root ratio and left ventricular end‐diastolic diameter normalized for body weight.

Conclusions and Clinical Importance

These results indicate that vitamin D status is associated with the degree of cardiac remodeling, and the serum 25(OH)D concentration begins to decrease before the onset of heart failure in dogs with CVHD.     

Genetic analysis of fat‐to‐protein ratio,milk yield and somatic cell score of Holstein cows in Japan in the first three lactations by using a random regression model

We estimated the genetic parameters of fat‐to‐protein ratio (FPR) and the genetic correlations between FPR and milk yield or somatic cell score in the first three lactations in dairy cows. Data included 3 079 517 test‐day records of 201 138 Holstein cows in Japan from 2006 to 2011. Genetic parameters were estimated with a multiple‐trait random regression model in which the records within and between parities were treated as separate traits. The phenotypic values of FPR increased soon after parturition and peaked at 10 to 20 days in milk, then decreased slowly in mid‐ and late lactation. Heritability estimates for FPR yielded moderate values. Genetic correlations of FPR among parities were low in early lactation. Genetic correlations between FPR and milk yield were positive and low in early lactation, but only in the first lactation. Genetic correlations between FPR and somatic cell score were positive in early lactation and decreased to become negative in mid‐ to late lactation. By using these results for genetic evaluation it should be possible to improve energy balance in dairy cows.     

Plywood frame corner joints with glued-in hardwood dowels

This paper presents research on plywood frame corners jointed to glulam beams and columns by means of glued-in hardwood dowels. The frame corner was made of a solid block of ordinary plywood of the same width as the glulam beams and with plies parallel to the plane of the frame to avoid splitting due to stress perpendicular to the grain. Hardwood dowels with a diameter of 12mm and a maximum glued-in length of 120mm were glued into drilled holes in the plywood corner and glulam beam ends parallel to the grain direction of the beams to form a momentresisting joint. Static bending tests were conducted of frame corners with 100 X 200mm² and 120 X 420mm² beam cross sections. Bending capacities of the joints corresponding to a modulus of rupture of the jointed glulam beams of about 30MPa were obtained for both closing and opening moments for the small cross sections, and about 22MPa was obtained for the large cross sections. Simple design models for calculation of joint strength and rotational stiffness are also presented.     

Plantlet regeneration from leaf protoplasts ofPopulus euphratica

Protoplasts were isolated from the leaves of sterile plants ofPopulus euphratica Oliv. by using 1% Cellulase “Onozuka” RS and 0.25% Pectolyase Y-23 in 0.6m of mannitol solution. Protoplasts were cultured in modified Murashige and Skoog's (MS) medium which contained no ammonium ions but was supplemented with BAP (6-benzylaminopurine), 2,4-D (2,4- dichlorophenoxy-acetic acid), and 1% sucrose at the cell density of 9×10⁴/ml. Cell divisions occurred in every culture medium, especially in the medium containing 0.5 mg/l of BAP and 0.1 mg/l of 2,4-D, in which callus was successfully induced by successive culture through cell cluster formation. Shoots were regenerated from the callus, and their growth was enhanced on 1/2 MS medium containing 0.8 mg/l of BAP. Finally, shoots were rooted and plantlets were regenerated on 1/2 MS medium without a hormone. A part of this paper was presented at the 106th Annual Meeting of the Jpn. For. Soc. (1995).     

Effect of loading frequency on fatigue life and dissipated energy of structural plywood under panel shear load

Wood-based panels are subjected to cyclic panel shear load caused by wind and seismic forces in such an application as the sheathing of bearing walls. The fatigue behavior of structural plywood under panel shear load with two different loading frequencies was examined. Pulsating panel shear load with a triangular waveform and loading frequency of 0.5 or 5 Hz was applied to the plywood specimens. Stress−strain hysteresis loops were measured throughout the fatigue tests. Fatigue life was highly dependent on loading frequency at more than 0.5 stress level. The deterioration of mechanical property and damage accumulation in plywood specimen was observed to be slower at higher loading frequency at more than 0.5 stress level. Analyses based on energy loss suggest that panel shear load with higher loading frequency causes less damage to the plywood specimen during one loading cycle at higher stress level, and that the fatigue damage accumulation causing failure might be dependent on stress level although it seems to be unaffected by loading frequency. Based on these results, a new fatigue failure model for plywood specimen was qualitatively developed by combining Weibull’s weakest link model and Daniels’ fiber bundle model.     

Determining Young’s modulus of timber on the basis of a strength database and stress wave propagation velocity I: an estimation method for Young’s modulus employing Monte Carlo simulation

In this article, we report on an estimation method for Young’s modulus that entails measuring only the stress wave propagation velocity of timber built into structures such as wooden buildings. Methods of estimating Young’s modulus that use the stress wave propagation velocity and characteristic frequency of timber in conjunction with timber density have long been used. In this article, we propose a method of easily and accurately estimating Young’s modulus from the stress wave propagation velocity without knowing the timber density. This method is based on a database of wood strength performance and density accumulated from a variety of research data and the method estimates Young’s modulus by a simulation method. We compared the Young’s moduli estimated by this method with those obtained by the bending test and by the measurement of the stress wave propagation velocity and density, and found similar results. This coincidence suggests that the method of estimating Young’s modulus presented in this article is valid. For example, the method is effective for convenient evaluation on site when determining whether a wooden building’s structural components should be reused or replaced when repairing or remodeling a building.     

Stress analysis of wood

Summary For the preparation of specimens for testing the stress distribution with the photoelastic method, various techniques are applicable. In this paper the so-called glass-transition temperature method is tested on a specimen imitating the layered structure of wood. The observations made on this specimen are compared with those obtained from a specimen with isotropic properties.

---

Zusammenfassung Für die Herstellung von Modellen zur Untersuchung der Spannungsverteilung mit spannungsoptischen Verfahren gibt es verschiedene Techniken. In dieser Mitteilung wird das sogenannte Glas-Übergangstemperatur-Verfahren an einem Modell, das den Schichtaufbau des Holzes nachahmt, geprüft. Die Beobachtungen, die an diesem Modell gemacht wurden, werden mit jenen verglichen, die sich an einem Modell mit isotropen Eigenschaften ergaben.