新疆日光温室前屋面的风载数值模拟分析

【目的】 对日光温室前屋面风载大小和变化趋势进行模拟,可辅助前屋面骨架结构优化设计和前屋面实际风载计算,为提前预测和防灾功能提供科学依据。【方法】 将日光温室墙体、保温被和骨架等结构简化,使用UG 软件对日光温室进行造型,将模型与空气进行布尔求差,得到整体模型,将整体模型导入到ANSYS ICEM中,进行网格划分,得到保温被4种工作状态薄膜风压。再通过Y向的9条曲线画出不同条件下风压变化对比曲线。【结果】 在无保温被和保温被全铺时,薄膜最南侧风压最高,约1.014×10⁵Pa,往北侧风压逐渐降低,脊高位置风压最小约1.010×10⁵Pa。由于最南侧风遇到薄膜阻碍,造成风压的升高,而北侧接近日光温室顶端,风速快,而风速快的位置风压小。在保温被全卷及半卷时,也是最南侧风压较最高,约1.014×10⁵Pa,往北有风压的降低,总体屋面风压变化比较小,约1.013×10⁵Pa。只是保温被半卷时,在保温被卷放位置会有风压的突变为1.012×10⁵Pa。【结论】 无保温被、保温被全铺、保温被全卷及保温被半卷4种情况南侧风压较大且相差不大,但越往北侧,保温被全卷或半卷会造成薄膜风压的升高,尤其是顶部的突然升高。保温被全铺是最佳防风方案。南侧风压高,南侧前屋面钢骨架拱形段的性能对日光温室结构稳定性和安全性至关重要,设计和建设时需要着重计算和核验。     

定量泵负载敏感系统卸荷压力冲击抑制研究

定量泵负载敏感系统在快速卸荷时容易出现压力冲击现象,对系统的可靠性和寿命产生较大危害。三通压力补偿阀是定量泵负载敏感系统中关键的调压元件,本文以三通压力补偿阀为切入点,建立定量泵负载敏感系统功率键合图模型,基于键合图模型推导系统的状态方程,建立Matlab动态仿真模型,探讨系统卸荷压力冲击的抑制方案。基于系统仿真模型,首先对系统卸荷压力冲击的仿真与试验进行对比,验证了仿真模型的正确性;然后,针对三通压力补偿阀的系统压力腔阻尼、阀芯直径、Ls腔阻尼、阀口锥角等关键参数,对卸荷压力冲击影响规律进行仿真;最后,基于关键参数对卸荷压力冲击影响规律的分析,提出了一种"小阀芯、双阀口"型三通压力补偿阀结构优化方案,并对其卸压冲击抑制效果进行了仿真和试验。结果表明,该方案可以有效抑制卸荷压力冲击,优化后系统卸压冲击压差比原系统降低了89%,卸荷压力降低了20%,进一步实现了节能。     

动态高压微射流对乌贼墨黑色素物理性质及微观结构的影响

为改善乌贼墨黑色素在食品中的应用性能,以虎斑乌贼(Sepia pharaonis)墨囊为原材料,采用碱性蛋白酶酶解制备乌贼墨黑色素,研究不同动态高压微射流(DHPM)(0、40、80、120、160、200 MPa)均质对其物理性质的影响,并采用红外光谱、扫描电子显微镜分析其微观结构。结果表明,DHPM处理使乌贼墨黑色素聚集体解聚,浊度增加、平均粒径减小,粒度分布更加集中和细微化,同时改善了其在去离子水和生理盐水中的溶解性;在压力作用下表现为粘度、空间色度值均有所增大;差示扫描量热法(DSC)分析表明,乌贼墨黑色素在120 MPa下热变性温度为90.70℃,焓变值为0.45 J·g^-1,且该压力下其贮藏稳定性最好;红外光谱分析表明,在特定压力处理范围内,DHPM处理使乌贼墨黑色素分子间形成了较强的氢键;扫描电镜观察发现样品颗粒在120 MPa处理后颗粒尺寸最小。因此,DHPM改性技术改善了乌贼墨黑色素的物理性质和微观结构,为其在食品工业中的应用提供了理论依据。     

动态高压微射流协同谷氨酰胺转氨酶复合修饰对鱼明胶凝胶特性和结构的影响

为了提高鱼明胶的凝胶特性,本试验采用动态高压微射流(DHPM)协同谷氨酰胺转氨酶(TG)交联(DHPM-TG)技术对鱼明胶进行复合修饰。结果表明,鱼明胶的亮度、特性粘度和胶融温度均随着TG含量的增加而增大,凝胶强度和硬度先增大后减小。与TG修饰技术相比,DHPM-TG复合修饰技术可显著提高鱼明胶的特性粘度、胶融温度、凝胶强度以及胶体的硬度和咀嚼性。此外,环境扫描电镜结果表明,DHPM-TG制备的鱼明胶胶体结构更加致密。综上,DHPM-TG复合修饰显著改善了鱼明胶的凝胶特性,为生产可替代哺乳动物明胶的高品质鱼明胶提供了新的理论依据。     

基于广义回归神经网络的灌溉系统首部多用户配水快速PID控制

针对多用户配水状态下灌区流量、压力需求变化范围大,传统流量、压力控制响应速度慢等问题,建立适用于多用户灌区配水的灌溉系统首部控制技术。该研究通过分析供水系统流量、压力调节方式,提出了流量、压力PID(Proportion Integration Differentiation)耦合调节方法,建立以电动阀开度为流量控制量、变频器频率为压力控制量对流量和压力进行调控的灌溉首部控制系统。为了减少系统的调节时间,提高系统的运行效率,采用广义回归神经网络(Generalized Regression Neural Network,GRNN)建立流量、压力和电动阀控制模拟量、变频器控制模拟量间的预测模型,形成神经网络PID控制模型(GRNN_PID),并进行模型精度和控制精度验证。GRNN训练结果显示,变频器控制模拟量的相对误差为0.11%～3.86%,电动阀控制模拟量相对误差为0.09%～5.74%,模型精度较高。使用3个调节过程模拟3个用户的需水行为对模型进行验证,结果表明,GRNN_PID模型3个过程的调节时间分别为11.6、10.7和7.2 s,PID模型3个过程的调节时间分别为31.7、29.6和16.9 s,GRNN_PID模型大幅减少了系统的调节时间,提高了系统的运行效率;分别计算了2种模型的控制精度,GRNN_PID调节方法和传统PID调节方法的稳态流量和压力误差都在1%以内,最大超调量为8%,控制精度较高但相差不大,表明GRNN是从策略上加速系统调节速度,其本身并没有对PID的参数进行调整,因此对系统的控制精度影响不大。研究可为灌溉系统流量压力快速控制提供参考。     

Revisiting the use of hydroxyethyl starch solutions in equine fluid therapy

The last decade has led to major shifts in opinions on the use of hydroxyethyl starch (HES) solutions in fluid therapy, specifically in human patients with sepsis. The majority of evidence documenting adverse effects of HES solutions on coagulation and renal health come from studies in people. However, these findings have led to investigation into the safety of HES solutions in veterinary species. While there are now studies investigating the effects of HES solutions on coagulation and renal health in dogs, cats and horses, information regarding long-term follow-up, clinical significance of these changes and use of these solutions in critically ill animals is still lacking. The information presented here serves to review the physiology of oncotic pressure and the rationale behind colloid use, specifically HES solutions. Additionally, the foundation of arguments against the use of HES and the available literature regarding HES use in animals will be summarised.     

Quantification of reservoir bags as airway pressure-limiting devices in a nonrebreathing system

ObjectiveTo evaluate the influence of reservoir bag types, volumes and previous use on the peak pressures (Pmax) and the times to develop 30 cmH₂O pressure (P30) within a nonrebreathing system with a closed adjustable pressure-limiting (APL) valve.Study designIn vitro study using three-way factorial design with repeated measure on one factor.SubjectsA total of 75 new anesthesia reservoir bags (five types, three volumes, five bags from each type × volume). The bag types were reusable latex (RL), disposable latex (DL) and three disposable neoprene (DN-1, DN-2 and DN-3).MethodsEach bag was tested three times (treatments): new, after prestretching and 1 week later. The bags were attached to a Bain system and anesthesia machine with closed APL valve and patient port with O₂ flow 2 L minute^–1 until Pmax was reached. The Pmax and time to reach P30 values were determined from recorded pressure traces. General linear mixed model analysis was used to examine the effects of bag type, volume and treatment. One-sided 95% upper prediction limits of Pmax were calculated to test the null hypothesis that predicted Pmax of new bags would be ≥ 50 cmH₂O for each factor combination.ResultsRL bags were the least and DN-3 bags were the most compliant. Prestretching increased compliance in all bag types. Smaller bags of RL, DL and DN-1 were less compliant than larger ones. The predicted Pmax values were < 50 cmH₂O only for DN-3 bags after prestretching. The time to reach P30 was critically low when using 0.5 L bags (median 17 seconds).Conclusions and clinical relevanceTo minimize the risk of barotrauma, highly compliant reservoir bags (e.g. DN-3) are recommended and reusable bags should be avoided. Bags should be prestretched before first use, 0.5 L bags should be avoided and fresh gas flow minimized.     

Evaluation of the agreement of two oscillometric blood pressure devices with invasive blood pressure in anaesthetized chimpanzees (Pan troglodytes)

ObjectiveTo evaluate the agreement of two noninvasive blood pressure devices: a human device with the cuff placed on the wrist (Omron R1) and a veterinary device with the cuff placed on the upper brachium (Surgivet Advisor Vital Signs Monitor) with invasive blood pressure (IBP) measurement in anaesthetized chimpanzees.Study designProspective clinical study.AnimalsA convenience sample of 11 adult chimpanzees undergoing anaesthesia for translocation and routine health checks.MethodsSystolic (SAP) and diastolic arterial pressures (DAP) were continuously recorded via a transducer connected to a femoral artery cannula, and at 5 minute intervals from the two oscillometric devices. Agreement was explored using Bland-Altman analysis and bias defined as the mean difference between the two measurement methods. Spearman correlation coefficients were calculated. Significance was set at p < 0.05.ResultsBias and standard deviation for the Surgivet compared with IBP were 8.6 ± 18 for SAP and 8.4 ± 9.9 for DAP, showing a significant underestimation of both variables. Limits of agreement (LOA) were from –27 to 44 for SAP and from –11 to 28 for DAP. Correlation coefficients between the Surgivet and IBP values were 0.86 for SAP and 0.85 for DAP (p < 0.0001). Bias and standard deviation for the Omron compared with the IBP were –21 ± 25 for SAP and –18 ± 15 for DAP, showing a significant overestimation of both variables. LOA were from –70 to –28 for SAP and from –47 to 11 for DAP. Spearman correlation coefficients between the Omron and IBP values were 0.64 for SAP and 0.72 for DAP (p < 0.0001).Conclusions and clinical relevanceAlthough neither device met all the criteria for device validation, the Surgivet presented better agreement with IBP values than the Omron in adult anaesthetized chimpanzees.     

VD在骨骼外系统中的作用及其研究进展

以往普遍认为VD的主要功能是调节Ca离子来促进骨骼的生长和预防佝偻病,但最近几年的研究发现,VD不仅在骨骼疾病中起到重要作用,还与多种骨骼外疾病密切相关,包括一些心血管疾病、代谢紊乱有关的疾病、恶性肿瘤、过敏性疾病、自身免疫性疾病、生殖方面影响等。目前对VD生物学功能的研究比较全面和深入,但大部分是针对人体和小鼠的基础研究,对诸如牛、猪、犬、猫等不同动物VD的骨骼外系统生物学功能的研究较少。在查阅相关文献的基础上,通过对VD在血压、免疫调节、内分泌、子宫内膜和骨骼肌方面的生物学功能和研究进展进行总结,为不同动物VD在骨骼外系统生物学功能的研究提供一定参考。     

离心泵叶轮出口宽度对泵腔内压力脉动分布的影响

在试验和数值模拟相互验证的基础上,开展叶轮出口宽度对离心泵泵腔内压力脉动分布影响的研究．通过试验和数值计算获得离心泵的外特性、泵腔内静压分布、泵腔内压力脉动分布及泵体表面的压力脉动幅值分布,并进行对比分析,结果表明：前泵腔内静压和压力脉动幅值随出口宽度的增大而增大,随半径的减小而增大;后泵腔内静压和压力脉动随出口宽度和半径的变化不十分明显．综合考虑外特性和压力脉动,在比转数 ns ＝97时叶轮出口宽度与叶轮出口直径之比应小于0.06;为了使压力脉动在泵腔内有效地衰减,出口宽度与前腔间隙的比值在1.81附近时最佳．研究结果可用于指导离心泵叶轮的优化设计．