基于含水率与温度补偿的土壤pH值在线实时检测系统

针对目前常用土壤pH值传感器在测量过程中受土壤含水率和温度影响较大的问题,设计了带有温度、含水率补偿模型的锑电极土壤pH值在线实时检测系统。利用最小二乘法对pH值和测量结果进行线性分析,补偿土壤pH值测量误差。试验结果表明,经过补偿之后,由温度和含水率变化导致的pH值测量误差至少可降低84. 5%,pH值测量值随温度和含水率的变化幅度不超过±0. 1。与市场产品ZD-18型土壤酸度计、HYSWR-ARC-12V型土壤含水率传感器、水银温度计对比研究得出,3项指标线性拟合决定系数均达到0. 99以上。为了确保自然环境下土壤pH值测量的适用性,探索了系统在使用过程中土壤含水率的阈值与测量精度,表明在土壤体积含水率大于5%的情况下均可有效测量。试验表明,在pH值3. 06～10. 36范围之内,本系统可有效测量,检测误差为-1. 53%～3. 51%,满足土壤pH值实时在线测量要求。     

小麦精量播种机排种高精度检测系统设计与试验

为实现小麦精量播种机播种量的精准检测,基于电容传感器设计了一套高精度小麦种子粒数检测系统。研究了小麦种子以单粒形式下落和多粒同时下落两种方式下的电容与小麦种子数目之间的关系。对于小麦种子以单粒形式下落,提出用差分动态阈值法检测小麦种子数目,试验表明检测的最大相对误差为1. 54%;对于多粒小麦种子同时下落,排种轮转速从20 r/min到55 r/min,每增加5 r/min,分别建立小麦种子数目与电容积分值之间的最小二乘回归模型。试验结果表明,根据实际转速和速度最近原则选择相应的回归模型,该系统对不同的排种转速均具有较高的检测精度,相对误差介于-2. 16%～2. 23%之间。对于小麦精量播种机不同的排种模式或不同的排种速度,所设计的排种检测系统均有较高的检测精度。     

基于近红外漫反射光谱的规模化奶牛场粪水氮磷定量分析及模型构建

为建立规模化奶牛场粪水中氮磷含量现场快速检测方法,以实现准确预测的同时替代常规监测程序,选取23家天津市典型种养结合模式的规模化奶牛场,围绕粪水处理全过程环节依次开展样品采集、实验室常规化学检测、近红外漫反射光谱采集,并进行主成分分析和偏最小二乘分析,建立多种动态复合影响因素条件下的全局、全程快速检测定量分析模型。结果表明:主成分分析不仅反映出同一奶牛场粪水有机组分随处理环节的变化,而且也反映出不同奶牛场粪水样品的差异性,以及在粪水处理过程中各因素对后续模型的影响程度。建立的全过程环节定量分析模型对总氮含量预测结果与实际含量的线性拟合相关系数R为0.96,预测均方根误差RMSEP为187.80;对总磷含量预测结果与实际含量的线性拟合相关系数R为0.91,预测均方根误差RMSEP为3.59。建立的全局定量分析模型对总氮含量预测结果与实际含量的线性拟合相关系数R为0.96,预测均方根误差RMSEP为238.59;总磷含量预测结果与实际含量的线性拟合相关系数R为0.91,预测均方根误差RMSEP为6.56。研究表明,基于近红外漫反射光谱和偏最小二乘法对规模化奶牛场粪水处理全过程环节粪水样品中氮、磷含量进行定量分析是可行的;纵向模型比横向模型能提供更好的预测结果;近红外漫反射光谱技术可实时、快速、高效地对规模化奶牛场粪水处理全过程总氮和总磷进行跟踪和监控。     

基于变分模态分解-BA-LSSVM算法的配电网短期负荷预测

配电台区日负荷序列呈现为既包含变化趋势、又含有波动细节的不规则曲线,该文借助变分模态分解(variational mode decomposition,VMD)将包含这些信息的原始日负荷序列分解为不同频率尺度的子序列,并结合一系列复杂的环境因素,分别利用不同的最小二乘支持向量机(least squares support vector machine,LSSVM)模型进行负荷预测,最后将基于不同频率分量的预测结果相加得到最终的日负荷预测结果。为了提高LSSVM预测能力,采用蝙蝠算法(bat algorithm,BA)对各LSSVM的参数进行寻优,同时,该文分析了影响负荷变化的环境因素,设计了一套因素归一化方法,预测过程考虑了环境因素的影响。仿真结果表明,该文提出的考虑复杂环境因素的预测思想及对历史日负荷进行VMD分解、BA优化、LSSVM预测的组合预测方法能有效提高短期日负荷预测的准确性。     

基于混合像元分解方法的康保县植被覆盖度估测

以康保县为研究区,使用Landsat8 OLI数据,结合134个野外样地调查数据,通过像元二分法、完全约束最小二乘法和随机森林三种方法来进行混合像元的分解,探讨混合像元分解方法对提取地表植被覆盖度的可行性。结果显示:基于随机森林的混合像元分解方法结果最优,F为0.664,RMSE为0.127;三种方法都能较为精确地估测出康保县的植被覆盖情况,且与实测数据较为拟合,因此采用混合像元分解的方法进行植被覆盖度估测是完全可行的。     

Assessing the utility of topographic variables in predicting structural complexity of tree stands in a reforested urban landscape

The transformation of natural landscapes into impervious built-up surfaces through urbanization is known to significantly interfere with the ecological integrity of urban landscapes and accelerate climate change and associated impacts. Although urban reforestation is widely recognised as an ideal mitigation practice against these impacts, it often has to compete with other lucrative land uses within an urban area. The often limited urban space provided for reforestation therefore necessitates the optimization of the ecological benefits, which demands spatially explicit information. The recent proliferation of tree stands structural complexity (SSC) and topographic data offer great potential for determining the ecological performance of reforested areas across an urban landscape. This study explores the potential of using topographic datasets to predict SSC in a reforested urban landscape and ranks the value of these topographic variables in determining SSC. Tree structural data from a reforested urban area was collected and fed into a tree stand structural complexity index, which was used to indicate ecological performance. Topographic variables (Topographic Wetness Index, slope, Area Solar Radiation and elevation)- were derived from a Digital Elevation Model (DEM) and used to predict SSC using the Partial Least Squares (PLS) regression technique. Results show that SSC varied significantly between the topographic variables. Results also show that the topographic variables could be used to reliably predict SSC. As expected, the Topographic Wetness Index and slope were the most important topographic determinants of SSC while elevation was the least valuable. These results provide valuable spatially explicit information about the ecological performance of the reforested areas within an urban landscape. Specifically, the study demonstrates the value of topographic data as aids to urban reforestation planning.     

基于BP神经网络的柴油发动机特性建模

建立连续的发动机燃油特性和调速特性数学模型作为液压机械无级变速器虚拟试验平台的动力源。根据虚拟平台对不同特性区域的精度需求对柴油发动机不同特性区域的试验数据进行不同的密度选取、乱序和归一化处理,采用单隐层BP神经网络对试验数据进行训练,对比不同隐层节点数网络的训练误差和测试误差,选取误差最小的网络,求解出网络的数学表达式。通过该方法以ISLe310柴油发动机为例建立燃油特性和调速特性的连续数学模型,这两个简单的数学表达式准确反映了发动机万有特性和外特性,连续模型避免了虚拟试验中出现信号的突变和奇异点。通过和经典的最小二乘法拟合得到的最优特性模型进行对比,其具有更小的误差、更强的泛化能力,能够更好地反映柴油发动机的相关特性。     

不同地区、不同部位羊驼毛品质性状的研究

本研究旨在了解不同地区、不同部位羊驼毛品质的差异，为羊驼选育及羊驼毛生产提供参考数据。采集新疆野生动物园、新疆阿勒泰、新疆阿克苏、山西、天津地区羊驼颌、颈、肩、侧、股、背、腹部位共636份毛样，进行平均纤维直径、毛丛长度、净毛率、单纤维强力、有髓毛含量、无髓毛含量等性状的测定，分析不同地区及不同部位毛品质性状的差异，并进行最小二乘分析。结果表明，不同地区羊驼毛平均纤维直径、白度、亮度、原毛油脂含量、净毛率、毛丛自然长度、单纤维强力、断裂伸长百分比、有髓毛含量、无髓毛含量均存在极显著差异（P<0.01）；不同取样部位羊驼毛纤维直径、原毛油脂含量、毛丛自然长度、单纤维强力、含杂率存在极显著差异（P<0.01），无髓毛含量和有髓毛含量存在显著差异（P<0.05）。以羊驼毛细度越细毛品质越优为准，结合单纤维强力、毛丛自然长度等性状，羊驼不同部位的毛纤维质量从高到低依次为：背、侧、股、肩、颈、颌及腹部。在育种中可将提高无髓毛含量作为新疆羊驼毛细度的选育目标，将提高净毛率和单纤维强力作为山西、天津羊驼毛育种方向，同时可考虑提高羊驼颈、颌、腹部的无髓毛含量，以提高羊驼整体毛品质水平。     

基于PLSR-BP复合模型的红壤有机质含量反演研究

对红壤地区土壤有机质进行快速预测,以满足智慧农业与精准施肥的需要。以江西省奉新县北部为研究区域,采用1 km×1 km标准格网划分研究区进行采样,共得到红壤样本248个。对土壤光谱进行了包含分数阶导数在内的3种数学变换方法,将经过P=0.01显著性检验的波段用于模型的构建,选用偏最小二乘回归(PLSR)和BP神经网络建立土壤有机质含量预测模型。结果表明:当对红壤光谱数据进行1.5阶导数变换后再使用PLSR-BP复合模型对土壤有机质含量进行预测时的结果为最优,训练集R~2=0.89,RMSE=4.68g·kg~(-1),验证集R~2=0.87,RMSE=5.55g·kg~(-1),RPD=2.75。1.5阶导数对红壤光谱数据的变换能够更好地突出与有机质相关的特征信息,有助于其含量预测。PLSR-BP复合模型预测精度优于单一模型,能够较好地预测红壤有机质含量,为精准农业快速监测红壤有机质含量提供了新的途径。     

Investigating the effects of simulated transport vibration on tomato tissue damage based on vis/NIR spectroscopy

Visible and near infrared (vis/NIR) spectroscopy combined with chemometrics were investigated to evaluate the effects of simulated transport vibration levels on damage of tomato fruit. A total of 280 tomato samples were randomly divided into 5 groups; each group was subjected to vibration at different acceleration levels. A total of 230 samples (46 from each group) were selected as a calibration set; whereas 50 samples (10 from each group) were selected as a prediction set. Raw spectra, differentiation (the first derivative) spectra, extended multiplicative scatter correction (EMSC) processed spectra and standard normal variant combined with detrending (SNV–DT) processed spectra were used for calibration models. SNV–DT processed spectra had the best performance using for partial least squares (PLS) analysis. The PLS analysis was implemented to calibrate models with different wavelength bands including visible, short-wave near infrared (SWNIR) and long-wave near infrared (LWNIR) regions. The best PLS model was obtained in the vis/NIR (600–1600 nm) region. Using a grid search technique and radial basis function (RBF) kernel, four least squares support vector machine (LS–SVM) models with different latent variables (7, 8, 9, and 10 LVs) were compared. The optimal model was obtained with 9 LVs and the correlation coefficient (r), root mean square error of prediction (RMSEP) and bias for the best prediction by LS–SVM were 0.984, 0.137 and 0.003, respectively. The results showed that vis/NIR spectroscopy could be applied as a reliable and rapid method for predicting the effect of vibration levels on tissue damage of tomato fruit.