Study on Design of Bio-clean Operating Room

The design of Bio-clean operating room in modern hospital is quite different from that of traditional operating room. This paper discusses three aspects of Bio-clean operating room design: air clean standard and air purification, interior equipment system and interior finish. It is hoped that this discussion will conduce to later designs.     

Simulation of the penetration rate (ROP) of the air percussion drilling

It is difficult to calculate the penetration rate (ROP) of percussion drilling. In the early research, the empirical or semiempirical formulae of the ROP are derived from the laboratory or field data collected by the researchers. However, the ROP value of the formulae is not as accurate as that in the field. Benefiting from the dynamic model, the geometric structure model and the theory of the roller cone bit, the mathematical model of the hammer bit, the mathematical model of the true bottom hole and the mathematical model between the tooth and the rock of the hammer bit are established. Hence the ROP of the air percussion drilling can be predicted by simulation. Field tests show the models are reliable and the results are coincident with that in the field. The research can help to redesign the hammer bit and optimize the drilling parameters.     

发动机用平板型空滤器流动阻力特性分析和改进

为减小平板型空滤器流动阻力以增大进气量,对平板型空滤器流动阻力特性开展了实验研究,获得了空滤器流动阻力随流量变化的规律和阻力构成成分。阻力随流量的增大而加速增大,滤芯阻力约占整个空滤器阻力的一半,入口流量为120 m 3/h时,总阻力为915.3 Pa,滤芯阻力为426.4 Pa。在实验获得滤芯阻力参数的基础上,提出采用多孔介质跃升模型对平板型空滤器内部流场开展三维数值仿真分析,结果表明,仿真结果与实验结果比较吻合,最大误差为5.67%。滤芯阻力同样约占整个阻力的一半,另一半阻力主要为出口处阻力,其余壁面阻力约占15%。最后,在实验和仿真分析的基础上,提出了改进模型并进行了仿真分析。结果表明,改进模型阻力有较大程度的下降,入口流量为120 m 3/h时,总阻力为588.2 Pa,较原始模型下降了32.2%;增大空滤器流通横截面积是减小阻力以增大进气量的有效手段,改进空滤器壁面的平滑性是补充措施。     

A STUDY ON HEAT AND MOISTURE STATE OF HULL LAYER FOR THERMAL INSTULATION OF A COLD STORAGE

This paper analyses the thermal moist characteristics of the hull layer beside an air layer at lower temperature in an envelope for a cold storage and presents a new method of waterproof by air layer. With test data from engineering practice, the theory on the barrier of self moisture proof at the surface sublayer of the hull layer in an attic on a cold storage is proven. The dried zone about three phase point is confirmed. It is a new knowledge for thermophysics on thermal design of a cold storage with an optimum thermal performance.     

Application of Matter Element Analysis in Assessment of Ambient Air Quality

A new method for assessment of ambient air quality is proposed by using matter element analysis.This model is simple and reasonable in assessment.The practical example is given,and compared with other methods.     

浅谈筒仓的熏蒸方法及对筒仓气密性要求

文章介绍了目前对筒仓采用的几种熏蒸方法。对筒仓气密性对熏蒸效果的影响进行了讨论，并提出了对密封的补救建议。     

泵站竖井进水流道数值模拟与装置特性试验

采用雷诺平均纳维—斯托克斯方程(RANS)和标准kε湍流模型,运用SIMPLEC算法,对椭圆型线前置竖井贯流进水流道内的流动进行了三维数值计算,揭示了竖井进水流道内流场、特征断面的速度分布及水力损失规律。对椭圆型线竖井进水流道与出水流道匹配组成的模型泵装置进行动力特性试验,得出了4种叶片角度下的泵装置特性曲线。研究结果表明:采用椭圆型线设计的竖井进水流道合理;大型低扬程泵站采用卧式竖井贯流结构,泵装置效率较高。     

四气门柴油机进气门出口流速的分布

对四气门柴油机在两个进气道单独和同时开启的情况下，利用热线风速仪测量进气门出口全圆周速度分布，并通过动量矩流率的计算，分析了两个进气道气流相互影响的变化规律及其主要影响因素。结果表明，在进气过程中，两个进气道之间的气流相互影响，造成了两进气门出口速度的再分配，进而导致了缸内气流绕气缸轴线动量矩流率的变化。动量矩流率的总量与两气道单独开启时相比有明显减少，这是两气道的组合涡流比小于单独气道涡流比的主要原因。两进气道之间的干扰程度与作用结果取决于气道本身的结构形状和相对位置。     

隔膜计量泵的改良设计与汽蚀性能的提高

针对应用于石油化工装置上的进口隔膜计量泵容易产生的汽蚀问题，对隔膜泵复合隔膜、柱塞密封副、液压平衡与补偿阀结构进行了改良设计，采用较大承载能力的机座、独特阶梯式活塞、加大直径的活塞、PTFE＋NBR复合隔膜，改良放气安全阀及油浸没式补偿系统等方法，提高了隔膜计量泵的汽蚀性能；通过对改造的隔膜计量泵与原有的计量泵进行的汽蚀试验对比，给出了隔膜计量泵性能与现场使用的最佳匹配工况。改良的结构设计和新型材料的选用大大提高了计量泵的汽蚀性能。     

新型肘形进水流道水力特性预测

提出一种新型肘形进水流道,具有型线简单,容易设计和施工方便等优点。采用定常雷诺平均N S方程和标准kε紊流模型,数值模拟了该新型肘形进水流道的三维紊流。在详细分析内部流态的基础上,从流道出口断面轴向流速分布均匀度、出口水流偏流角和流道阻力系数3个方面对其水力特性进行了全面的预测,并与按常规设计的肘形进水流道的水力特性进行了比较。计算结果表明,新型肘形进水流道具有优良的水力特性,出口水流的轴向流速分布均匀度高,偏流角小,可为水泵提供良好的进水条件。