Analysis of Heat Transfer and Optimal Parameters of Multi-louvered Fin Condenser

The authors conduct the experimental study and optimal computing for the condenser of automobile air conditioner. The especially the properties of heat transfer and flow at the side of air when using shutter fin. The authors the influence of several combinations of fin's geometry parameter to heat transfer and flow resistance. The maximal heat transfer is used as a criterion relation to select the fin's geometry parameters in the same facing air area of condenser. Furthermore, a program is designed to conduct optimal computing, and the computing results are basically consistent with experimental results. It shows that the optimal method is reasonable and the results can be applied to engineering practice.     

Determination of Pile-Soil Parameters for Steel Pipe Pile Subjected to Lateral Load

In this paper,in terms of the measured data(including the deflection and slope at the ground surface of the pile,the maximum bending moment and its position),the biparameter method is used to analyze the pile-soil parameters.Two examples show that the method in present paper is reasonable and reliable,and it provides the reference value for the engineering design.     

The Optimization Design for the Parameters of Capacitor Welding

Through the analysis in this paper,the optimum relation of the discharging current peak interval t m ,the discharging loop equivalent inductance L and equivalent resistance R is obtained.This paper analyze the original discharging loop equivalent inductance L ,which provides an effective method for adjustment and selection of inductance L to realize the optimization energy saving design of the welding machine.     

OPTIMAL DESIGN WITH WHOLE STRUCTURE PARAMETERS OF LOWER PART OF HUGE EXCAVATOR

A optimal design with whole structure parameters and its program are carried out. A reasonable model is established. Using the method a optimal design with whole structure parameters by original parameters of American P&H2300xp excavator was calculated. The size,carried out by the method,approximates to the size of P&H2300xp excavator very well.     

On Determinative Parameters of SDOF Systems in Elasto- plastic Earthquake Response

Parameters dominating elasto- plastic earthquake response of SDOF systems,relation between ground motion amplitude and elasto- plastic response of SDOF systems are presented in this paper.     

Robust Adaptive Control Based on On-line Identification to Multi-parameters

In system controlled,Sampling these parameters and with parameters for controller in time, it is an object to adaptive control. The article presents a scheme that the structure parameters on it's model and model parameters is robust identified by on line, while to optimal of algorithm on adaptive control is fulfilled. In control scheme, method of intelligent identifying to the structure parameters(levels of model) and algorithm of robust pole placement are introduced also It is advancer for already mentioned scheme. Whole scheme presents new model on adaptive control.     

强度参数统计特性对边坡稳定可靠性的影响

由于对边坡强度参数统计特性考虑不全面,使得边坡可靠性指标计算值偏小,对应的失效概率偏大,常常超过10%,设计中难以采纳,造成地基可靠度规范的制定和执行进展缓慢。以某高速公路全风化花岗岩土质高边坡为工程背景,在分析土质参数统计特性的基础上,采用极限平衡理论和蒙特卡罗模拟法,系统地分析了土质强度参数的均值不定性、变异性、相关性、区间特性和空间变化性等对边坡稳定可靠性的影响。结果表明：土性参数的各种统计特性对边坡稳定可靠性均具有不同程度的影响。可靠性指标计算值随抽样距离的减小而增加,随c或φ均值的增大而增加,随c和φ的变异系数的增大而减小,随c和φ相关系数绝对值的增大而增加,考虑区间性后可靠性指标计算值也明显变大。即变异性对边坡稳定不利,而相关性、区间性和空间变化性对边坡稳定有利。因此,准确而全面地考虑土质参数的统计特性,尤其是在参数变异性和相关性的基础上加以考虑土性参数空间变化性和区间性会更加符合工程实际,且计算结果趋于安全,有利于地基可靠度规范的推广运用和边坡工程的安全评价。     

结构参数对水润滑橡胶合金轴承摩擦噪声的影响分析

为了研究水润滑橡胶合金轴承结构参数对其低速重载工况下摩擦噪声的影响,使用复模态分析方法建立了水润滑橡胶合金轴承系统仿真模型,采用专业仿真软件分析了不同摩擦系数及结构参数条件下摩擦噪声产生的概率,进而研究结构参数对摩擦噪声的影响,进行了平板型和圆弧型结构的水润滑橡胶合金轴承摩擦噪声的对比实验。研究结果表明,水润滑橡胶合金轴承的水槽半径大小、摩擦面形状以及摩擦副的摩擦系数对水润滑橡胶合金轴承的摩擦噪声有较大影响,而水槽的形状对轴承摩擦噪声的影响不大。对一定结构尺寸的水润滑橡胶合金轴承,水槽半径为4 mm、平面型摩擦面的结构可以大大减少轴承出现摩擦噪声的可能性,相关实验结果与计算结果是吻合的。     

小黄鱼热泵干燥工艺及设备选型分析

研究了不同热泵干燥温度下小黄鱼的干燥特性,并对其干燥品质进行分析。结果表明在干燥温度55℃、铺放密度为6.48 kg/m2的条件下干燥时间为13.5 h,干燥品质最优。在综合考虑能耗、企业加工条件和产品品质的前提下,将生产工艺参数确定为:干燥温度60℃、铺放密度为6~7 kg/m2,干燥时间为10~12 h。根据企业日处理量5.5~6.0 t的加工要求,通过对产能核算及加工成本计算,确定设备选型方案为:1台GHRH-510型热泵干燥机与2台GHRH-340型热泵干燥机,该方案投资回报期短,社会效益明显。