小黄鱼热泵干燥工艺及设备选型分析

研究了不同热泵干燥温度下小黄鱼的干燥特性,并对其干燥品质进行分析。结果表明在干燥温度55℃、铺放密度为6.48 kg/m2的条件下干燥时间为13.5 h,干燥品质最优。在综合考虑能耗、企业加工条件和产品品质的前提下,将生产工艺参数确定为:干燥温度60℃、铺放密度为6~7 kg/m2,干燥时间为10~12 h。根据企业日处理量5.5~6.0 t的加工要求,通过对产能核算及加工成本计算,确定设备选型方案为:1台GHRH-510型热泵干燥机与2台GHRH-340型热泵干燥机,该方案投资回报期短,社会效益明显。     

真空带式、真空冷冻及热风干燥香蕉浆的比较

以香蕉为原料,比较真空带式、真空冷冻及热风3种方式干燥香蕉浆的效果。结果表明:真空冷冻干燥物料中的大部分水分在升华阶段去除,热风干燥初期水分含量迅速下降,真空带式干燥物料水分随时间延长呈比较均匀的下降。真空冷冻干燥、真空带式干燥的产品品质优于热风干燥。真空冷冻及真空带式干燥产品的截面、表面和底面孔洞结构都有较大区别。     

A mathematical model for border irrigation II. Vertical and horizontal recession phases

Summary This paper, second in a series of three, develops a mathematical model, using the volume balance approach, to simulate vertical and horizontal recession of border irrigation. An equation is proposed for computing Manning's roughness factor N in both laminar and transitional flow regimes in recession phases. The model has four parameters which can be determined experimentally. Experimental data from ten vegetated as well as nonvegetated borders were used to verify the model. Average difference (AD) between calculated and observed vertical recession times was less than 4.4 min, and between calculated and observed horizontal recession times less than 4.6 min for the ten experimental data sets. Average relative error (ARE) in computed horizontal recession was less than 13% for these data sets. The model was found to be especially accurate for Reynold's number between 1,800 and 2,500.     

激振式扭转疲劳试验台载荷波形畸变分析

针对行星式离心激振扭转疲劳试验台在进行汽车传动轴扭转疲劳试验时出现的载荷波形畸变现象,分析了试验台扭振系统并建立了数学模型,导出交变扭矩幅值变化的数学表达式。通过试验分析和计算机模拟验证了数学模型,找到了扭矩波形畸变的根本原因,并提出了消除波形畸变的方法,为合理使用原有这类试验台及新设计这类试验台提供了理论依据。     

Modeling soil water dynamics in a drip-irrigated intercropping field under plastic mulch

Intercropping, drip irrigation, and the use of plastic mulch are important management practices, which can, when utilized simultaneously, increase crop production and save irrigation water. Investigating soil water dynamics in the root zone of the intercropping field under such conditions is essential in order to understand the combined effects of these practices and to promote their wider use. However, not much work has been done to investigate soil water dynamics in the root zone of drip-irrigated, strip intercropping fields under plastic mulch. Three field experiments with different irrigation treatments (high T1, moderate T2, and low T3) were conducted to evaluate soil water contents (SWC) at different locations, for different irrigation treatments, and with respect to dripper lines and plants (corn and tomatoes). Experimental data were then used to calibrate the HYDRUS (2D/3D) model. Comparison between experimental data and model simulations showed that HYDRUS (2D/3D) described different irrigation events and SWC in the root zone well, with average relative errors of 10.8, 9.5, and 11.6 % for irrigation treatments T1, T2, and T3, respectively, and with corresponding root mean square errors of 0.043, 0.035, and 0.040 cm³ cm^?3, respectively. The results showed that the SWC in the shallow root zone (0–40 cm) was lower under non-mulched locations than under mulched locations, irrespective of the irrigation treatment, while no significant differences in the SWC were observed in the deeper root zone (40–100 cm). The SWC in the shallow root zone was significantly higher for the high irrigation treatment (T1) than for the low irrigation treatment, while, again, no differences were observed in the deeper root zone. Simulations of two-dimensional SWC distributions revealed that the low irrigation treatment (T3) produced serious severe water stress (with SWCs near the wilting point) in the 30–40 cm part of the root zone, and that using separate drip emitter lines for each crop is well suited for producing the optimal soil water distribution pattern in the root zone of the intercropping field. The results of this study can be very useful in designing an optimal irrigation plan for intercropped fields.     

金属注射成形技术在喷雾机零件制造中的应用

概述了金属注射成形技术的工艺过程和特点，给出了在喷雾机喷雾头组件这一典型农机零件上的应用实例，并对喷雾头组件用注射成形工艺制造中粘结剂成分的选择、混炼工艺、脱脂方法和烧结过程等进行了探索。通过研究制造出了尺寸精度和力学性能均满足要求的产品，产品致密度达到98．5％。生产工艺得到明显简化。     

汽油机冷起动HC排放的机理与控制策略

为适应欧Ⅲ以上汽车法规,对点燃式发动机冷起动工况下HC排放的研究已经成为目前发动机领域的热点之一.为了更好地控制冷起动排放,合理组织燃烧过程,要求对点燃式发动机冷起动HC排放特性有更深入的了解.本文基于国内外研究进展,介绍了冷起动工况下催化器前发动机HC排放的特点,影响排放的重要因素,以及形成的机理,特别是进一步降低和控制冷起动HC排放的发展方向.     

车辆表面脉动压力的试验研究

对车辆表面脉动压力与气流噪声的关系进行了讨论，说明了偶极子源噪声在车辆气流噪声中占主导地位，而车辆气流噪声中的偶极子源噪声又取决于车辆的表面脉动压力，阐述了研究车辆表面脉动压力对进一步研究和控制车辆气流噪声具有的重要意义。在此基础上，对车辆表面脉动压力的分布、频率特性及其与车速的关系进行了试验研究，得到了一些有意义的结论。     

基于框架理论的变电站操作票自动生成系统

介绍了一种基于框架理论的变电站操作票自动生成系统。该系统用框架知识表示法来描述电力系统的设备参数，建构了一个直观的、层次分明的数据结构。通过融合框架理论于面向对象的语言VC 中，开发出了一个集通用、实用、智能于一体的操作票专家系统。     

Incorporation of ridge and furrow method of rainfall harvesting with mulching for crop production under semiarid conditions

A plastic-covered ridge and furrow rainfall harvesting (PRFRH) system combined with mulches was designed to increase water availability to crops for improving and stabilizing agricultural production in the semiarid Loess region of northwest China. The system was built by shaping the soil surface with alternate ridges and furrows along the contour. The plastic-covered ridges served as a rainfall harvesting zone and furrows as a planting zone. Some materials were also used to mulch the furrows to increase the effectiveness of the harvested water. This system can make better utilization of light rain by harvesting rainwater through the plastic-covered ridge. The field experiment (using corn as an indicator crop) showed that grain yields in the PRFRH system with mulches in 1998 and 1999 were significantly higher than the controls, with an increase of 4010–5297 kg per ha (108–143%). In most treatments, the water use efficiencies (WUE) were in excess of 2.0 kg m⁻³. The WUE values of corn in this system were 1.9 times greater than the controls in 1998 and 1.4 times greater than the controls in 1999. The plastic-covered ridge led to a yield increase of 3430 kg per ha (92%) in 1998 and of 1126 kg per ha (21%) in 1999 compared with the uncovered ridge. On average, the additional mulches in the furrow brought about a yield increase of 8–25%. Based on the results of this study and other researches, this technique can increase corn grain yield by 60–95% in drought and average years, 70–90% in wet years, and 20–30% in very wet years. The PRFRH system had the potential to increase crop yield and produced greater economic benefit, therefore it could be used in regions dominated by light rainfall of low intensity where crops generally fail due to water stress.