Compression properties of weft knitted fabrics consisting of shrinkable and non-shrinkable acrylic fibers

High-bulk worsted yarns with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yarns and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and 2000 g/cm²) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40% shrinkable fibre blending ratio the maximum yarn bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20% shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V′) which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knitmiss structures. In addition, at 20% shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.     

Effect of chemical softening of coconut fibres on structure and properties of its blended yarn with jute

Coconut fibres were subjected to chemical treatment to obtain softer and finer fibres, suitable to blend with other finer fibre like jute. The chemical softening recipe was optimized using Box-Behnken design of experiments as 40 % Na₂S, 10 % NaOH and 6 % Na₂CO₃, which notably reduced the fineness (33 %) and flexural rigidity (74 %) and improved tensile property of coconut fibre. Effect of softening of coconut fibre on its process performance was studied in high speed mechanized spinning system at different blend ratios with jute. Blending with jute assists in spinning of coconut fibre to produce yarn of 520 tex at production rate of 5-6 kg/h, as compared to 15 kg/day for hand spun 5300 tex raw coconut fibre yarn in manual system. Analysis of blended yarn structure in terms of packing density, radial distribution of fiber components (SEM) and mass irregularity were investigated. SEM shows yarns made from softened coconut fibre -jute blends are more compact than raw coconut fibre -jute blend yarns. Coconut fibres were preferentially migrated to core of the yarn. Major yarn properties viz., tensile strength, and flexural rigidity of raw and chemically softened blended yarns were compared against their finest possible 100 % coconut fibre yarn properties. Yarn made up to 50:50 chemically softened coconut fibre-jute blend showed much better spinning performance, and having superior property in terms of reduced diameter, higher compactness, strength, initial modulus and less flexural rigidity than 100 % raw, 100 % chemically softened coconut fibre rope, and raw coconut fibre-jute blend yarns.     

A comparative study on performance properties of yarns and knitted fabrics made of biodegradable and conventional fibers

Biodegradable products are parts of a natural cycle. The biopolymers and the fibers that can be produced from them are very attractive on the market because of the positive human perception. Therefore, PLA being a well known biodegradable fiber and some conventional fibers were selected for the current study to examine the differences between them and to emphasize the importance of biodegradability beside fabric performance. 14.8 tex (Ne 40/1) combed ring spun yarns produced from biodegradable fiber PLA, new generation regenerated fibers Modal and Tencel, synthetic and blends 50/ 50 % cotton/polyester and 50/50 % viscose/polyester, polyester were selected as yarn types and by using these yarns, six knitted fabrics were produced and some important yarn and fabric properties were compared. In this context, moisture and the tensile behavior of yarns and pilling, bursting strength, air permeability and moisture management properties of the test fabrics are discussed.     

Investigating the effect of various blend ratios of prepared masterbatch containing Ag/TiO2 nanocomposite on the properties of bioactive continuous filament yarns

In this research, possibility of producing and processing antibacterial organic/inorganic nanocomposite polypropylene filament yarns for permanent antimicrobial efficiency has been investigated. First PP powder and inorganic nanocomposite filler were mixed in a twin screw extruder and modified masterbatch was produced. Continuous filament yarn was made by a pilot plant melt spinning machine from the blend of PP granule and various blending contents of the prepared masterbatch. Pure PP and all other combined samples showed acceptable spinnability at the spinning temperature of 240 °C and take-up speed of 2000 m/min. After producing as-spun filament yarns, samples were drawn, textured and finally weft knitted. Physical and structural properties of as-spun and drawn yarns with constant and variable draw ratios were investigated and also tensile and crimp properties of textured yarns were evaluated. Moreover, the DSC, SEM, FTIR techniques have been used for characterization of samples. Finally antibacterial efficiency of knitted samples was evaluated. The experimental results indicated that the maximum crystallinity reduction of modified drawn yarns has reached to 5 %. The observed improvement in the tensile properties of modified as-spun yarns compared to the pure PP was significant. Drawing process improved generally the tensile properties of as-spun yarns. Tensile properties of modified textured and drawn yarns were higher than the pure PP. An optimum of antibacterial activity has been observed in the sample containing 0.75 wt% of nano-filler. It is interesting that the optimum of tensile properties has been also obtained for the sample with maximum bioactivity.     

Studies on structural integrity of polyester-cotton friction spun yarn by cycling extension test

Yarns and fabrics are subjected to a low level of stresses or strains of repetitive nature in processing and actual use which leads to breakage, permanent deformation, bagging and loss of useful life of the product. The ability of the spun yarns and fabrics to withstand such stresses depends upon their structural integrity. A structurally rigid yarn (i.e. yarns in which fibres are tightly bound) would behave more like an elastic solid and consume more energy during deformation as the constituent fibres have to be deformed. Once the strain is released, the recovered energy will also be more. On the other hand if the structural integrity of the same yarn is poor, fibres would easily slip during deformation and would consume much less energy. The recoverable energy also will be much less. The present investigation reports on the structural integrity of friction spun yarns in terms of energy loss or decay by employing cyclic extension test. It has been observed that friction spun yarns in which the core is immediately wrapped by long and strong polyester fibre layer make the structure strongest as polyester is expected to form tight wrappings. The decay in deformation energies during extension cycling depends upon sheath structure i.e. its composition and location of constituent fibres in sheath layers. With increase in core fibre %, the decay has been found to increase. However, the decay values discriminate more between core% differences than between sheath fibre layer arrangements.     

Evaluation of flax accessions for high value textile end uses

Due to recent changes in EC subsidies for flax cultivation it has been difficult to grow short fibre flax profitably in the UK. The Texflax project aimed to demonstrate that high quality flax fibre can be produced and processed on short fibre cotton spinning systems. Initially 92 flax accessions were cultivated on test sites in the UK over three growing seasons to explore the range of fibre diameter found in fibre flax. The efficacy of applying a translocating herbicide at different stages of plant maturity for optimum fine fibre production was explored. A range of factors indicated that application at the midpoint of flowering stage is favourable for the desiccation of flax and onset of retting. Fibre was caustic extracted using a laboratory method developed at De Montfort University, and fibre evaluated in terms of diameter, length, consistency and cleanliness. At the end of the project five accessions from the original 92 were chosen as producing optimal quality fibre suitable for high value textile end uses. Improved agronomy and subsequent processing enabled yarns with a 50:50 cotton:flax blend to be spun at 26 N m yarn count, the normal blend ratio for this count being 70:30. The yarn properties show an improvement when compared to standard products and finer quality fabrics have been prepared using the yarns.     

Spinning performance and antibacterial activity of SeaCell® active/cotton blended rotor yarns

Microorganisms can lead to functional, hygienic and aesthetic (e.g. deterioration, staining) problems on textile products. Natural fibers especially cotton are more easily affected by microorganisms. Blending of cotton fibers with antimicrobial fibers can enhance the protective properties of products against microorganisms. Demand of antimicrobial performance from the products changes depending on the application area. Therefore determination of suitable antimicrobial fiber quantity for the desired application is important. In this study the spinning performance of SeaCell Active/cotton blended open end rotor yarns and antibacterial activities of fabrics produced by these blended yarns were investigated. Five different cotton/SeaCell Active blended slivers with SeaCell Active content from 3 % up to 53 % were prepared on drawframe machine and all slivers were spun into yarns on open end rotor spinning machine at a yarn count of 20 tex with α_Tt=3827 twist coefficient. The effects of rotor speed, opening roller speed, rotor, opening roller and navel type on the quality parameters of SeaCell Active/cotton blended yarns were investigated. Tensile properties, hairiness, unevenness and IPI values of the yarns were reported. All types of cotton/SeaCell Active blended yarns were knitted on a circular knitting machine. Antibacterial activity of the fabrics was analyzed quantitatively. Antibacterial tests showed that good antibacterial activity can be achieved after several washings even with 3 % of SeaCell Active fibers in fabrics.     

Manufacture technique and electrical properties evaluation of bamboo charcoal polyester/stainless steel complex yarn and knitted fabrics

There are derivative problems of electromagnetic wave radiation accompanying the advances of science and technology nowadays and secure protections are also emphasized gradually. To shield these electromagnetic wave radition jeopardizing people’s health, in this study, stainless steel wires were the core yarn and bamboo charcoal polyester textured yarns were the wrapped yarn. The bamboo charcoal polyester/stainless steel (BC/SS) complex yarns were manufactured using a rotor twister machine. The BC/SS complex knitted fabrics were woven with the complex yarns employing a circular knitting machine. Three manufacture parameters were the wrapped amount of the complex yarn (2 to 6 turns/cm), the lamination amount of the knitted fabrics (1 to 6 layers) and lamination angles of the knitted fabrics (0°/0°/0°/0°/0°/0°, 0°/45°/90°/−45°/0°/45°, and 0°/90°/0°/90°/0°/90°). The knitted fabric exhibited the lowest surface resistance 32.3 Ω/sq. Optimum electromagnetic shielding effectiveness (EMSE) was 45 dB when the knitted fabrics were with 0°/45°/90°/−45°/0°/45° laminating in 0.51 GHz.     

The Effects of Fabric and Conductive Wire Properties on Electromagnetic Shielding Effectiveness and Surface Resistivity of Interlock Knitted Fabrics

Our aim in this study was to investigate the effects of course density, yarn linear density and thickness and type of conductive wire on electromagnetic shielding effectiveness. Metal/cotton conductive composite yarns were produced by the core-spun technique on the ring spinning machine, involving stainless steel, copper and silver coated copper wires with 40 μm, 50 μm, 60 μm thicknesses and Ne10/1 and Ne20/1 count yarns. The interlock fabrics were knitted on a 7G flat knitting machine with the three different machine settings. The EMSE and the surface resistivity of knitted fabrics were measured by the co-axial transmission line method according to the ASTM-D4935-10 standard in the frequency range from 15 to 3000 MHz and by the ASTM D257-07 standard, respectively. It was observed that all fabrics shielded around 95 % of electromagnetic waves at low frequencies, 80 % at medium frequencies and 70 % at high frequencies. Increasing the course density and thickness of conductive wire in interlock knitted fabrics increased the EMSE correspondingly. The knitted fabrics that had been produced with high yarn count showed greater EMSE because there was less isolation. The effect of the metal wire type was highly significant between 15 and 600 MHz.     

混纺麻纱特征的实用图像表征技术——I.截面图像生成与特征指标

混纺织物的纤维组成和混纺比早在成纱时就已确定,其预先判定极为必要。本文探讨图像技术测量麻/涤混纺纱混合比的快速算法及其实用指标。该表征从麻/涤纱的有效切片、纱线截面摄像、图像小波分析去噪开始,到采用形态滤波法,解决图像局部灰度不均匀;使用分水岭法,分开粘连纤维和减少无效分割,实现图像的采集和预处理。实验结果证明,切片采样和小波除噪可达清晰采像要求;图像预处理可有效提高图像质量和分析精度。由此对纤维截面几何特征分析,得出主要特征参数为纤维当量截面积、异形系数和中腔纹。并依此参数及其组合完成对苎麻和涤纶纤维的自动识别,准确率达99.5%.     

The mechanism and/or prediction of the breaking elongation of polyester/viscose blended open-end rotor spun yarns

In this study, an analysis on the breaking elongation mechanism of the polyester/viscose blended open-end rotor spun yarns has been carried out. In addition, a back propagation multi layer perceptron (MLP) network and a mixture process crossed regression model with two mixture components (polyester and viscose blend ratios) and two process variables (yarn count and rotor speed) are developed to predict the breaking elongation of polyester/viscose blended open-end rotor spun yarns. Seven different blend ratios of polyester/viscose slivers are produced and these slivers are manufactured with four different rotor speed and four different yarn counts in rotor spinning machine. In conclusion, ANN and statistical model both have given satisfactory predictions; however, the predictions of ANN gave relatively more reliable results than those of statistical models. Since the prediction capacity of statistical models is also obtained as satisfactory, it can also be used for breaking elongation (%) prediction of yarns because of its simplicity and non-complex structure. In addition, it is also found in this study that yarn count, rotor speed and breaking elongation of polyester-viscose fibers and the blend ratios of these fibers in the yarn have major effects on yarn breaking elongation.     

Comparative study on the characteristics of knitted fabrics made of vortex-spun viscose yarns

Murata vortex spinning system is based on the air jet spinning system. The vast majority of previous works deal with the properties of vortex spun (VS) yarn and the spinning system. In this study, we investigated knitted fabrics from VS yarn in comparison with fabrics from ring (RS), compact (CS) and open-end rotor (OES) spun yarns made from viscose. The effect of yarn spinning system on dimensional and physical properties of knitted fabrics was explained with specific attention to fabrics from VS yarn. Shrinkage of fabrics from VS yarn has the lowest at widthwise direction, while having the highest at lengthwise direction. It is shown that the order of fabric spirality and twist liveliness for yarns from different spinning systems are quite similar. However, relation between loop shape factor and angle of spirality is inconsistent. Angle of spirality of fabrics from VS yarn is higher than fabrics from OES yarn, but lower than that of others. The bursting strength of fabrics from VS yarn is lower than that of those from RS and CS yarns and higher than that of those from OES yarn. From this study, it is also evident that fabrics from VS yarn have the lowest pilling tendency and highest resistance to abrasion.     

Comparative study on the effect of blend ratio on tensile properties of ring and rotor cotton-polyester blended yarns using concept of the hybrid effect

Study on the characteristics of blended ring and rotor spun yarns is a topic of major interest to the researchers. The overall properties of these blended yarns are affected by the relative proportion, properties of the components and their interactions. The main focus of this work is on comparing and analyzing effects of blend ratio on tensile properties of the yarns produced in different spinning systems using concept of hybrid effects that has not received enough attention from researchers. Various blends of cotton-polyester ring and rotor spun yarns were prepared. Tensile properties of the samples were examined as well. Interactions between cotton and polyester fibers was evaluated through predicting strength and elongation at break of the yarns using simple rule of mixtures (ROM) and hybrid model. Experimental results showed that, the effect of different blend ratios on tensile properties of the samples is different. In comparison with 100 % cotton yarn, promotion in braking strength of the ring and rotor spun samples occurred after increasing fraction of the polyester fiber to 50 and 66.5 % respectively. The prominent finding of the present work is that the trend of change in tensile properties of different yarns versus blend ratio is predictable via hybrid model and migration behavior of the constituent fibers. Coefficients representing the intensity of the interaction and migration index of the fibers were calculated and all results were discussed based on these calculated factors.     

Assessing the relationship among fabric constructional parameters, fractional reflectances and cover factors of polyester fabrics by experimental and mathematical methods

This paper focuses on the assessment of the relation among constructional properties, fractional reflectances and cover factors of fabrics woven from polyester yarns. A novel equation for the calculation of the relation between fractional reflectance and fabric cover factor was proposed and the usage of the equation was assessed by reflectance measurements. 48 polyester fabrics having different constructional parameters were used and the fabrics differed from each other by their cover factors. The warp yarn type and count, warp density and warp yarn twist were the same but weft yarn count, weft yarn fiber count and weft density were different for the fabrics in the experimental sub-groups. The reflectance measurements were conducted on the pretreated but undyed fabric samples as well as on the individual yarn systems of the same fabrics. Fabrics with the same cover factors exhibited different fractional reflectances. Reflectances were found to be dependent on the cover factor as well as on yarn fiber fineness, yarn count, yarn density and fabric weave. The changes in crimp of the yarns according to different construction parameters also governed the changes in fractional reflectances of fabric surfaces. The proposed equation was tested according to different fabric construction parameters and it was concluded that fiber fineness and weave pattern were among the most important parameters which govern the total light reflectances from the fabric surfaces, although they are not incorporated in the calculation of the fabric cover factors. The proposed equation was used to explain the effects of these components on the reflectance behavior of the fabric surfaces and on fabric cover.     

Investigation on the Biodegradability and Antibacterial Properties of Nanohybrid Suture Based on Silver Incorporated PGA-PLGA Nanofibers

Polyglycolic acid-poly lactic glycolic acid (PGA-PLGA) electrospun nanofibers containing silver nanoparticles have been produced and twisted into the nanofibrous yarn. The morphology of nanofibers and produced yarns, as well as the mechanical properties of the yarns, were investigated. Furthermore, in vitro antibacterial properties and in vitro degradation behavior of yarns containing various silver nanoparticles were studied. SEM images confirmed that the addition of the silver nanoparticles into the polymer solution increases the fiber diameters. The result of the mechanical test of the yarns alone and used in two different forms of the knots was measured and results showed that the strength of the yarns without the knot was significantly more than that of others. The biodegradability test showed that the mechanical properties and the weight of the yarns were quickly reduced after subjecting to in vitro condition. The result of the antibacterial test indicated that the nanofiber yarns containing %3 silver nanoparticles were the most appropriate sample with a considerably antibacterial activity against both gram-positive bacterium Staphylococcus aureus and gram-negative bacterium Escherichia Coli with inhibition zones of 8.1 and 9.5 mm, respectively; which demonstrated that silver nanoparticles retained their effectiveness after the electrospinning process. Therefore the nanofibrous yarns containing silver nanoparticles could be successfully produced by the electrospinning process with the proper antibacterial property as a candidate for the surgical sutures.     

Reflectance prediction of colored polyester fabrics by a novel formula

This paper focuses on the reflectance prediction of colored (unicolored) fabrics considering relationship between fractional reflectance values and cover factors of fabrics woven from polyester yarns. A novel equation for the calculation of relation between fractional reflectance and cover factor was proposed and usage of the equation was assessed by reflectance measurements. 48 dyed polyester fabrics having different constructional parameters were used and fabrics differed from each other by their cover factors. Warp yarn type and count, warp density and warp yarn twist were the same but weft yarn count, weft yarn fiber count and weft density were different for the fabrics in experimental sub-groups. The reflectance measurements were conducted on the dyed fabric samples as well as on the individual yarn systems (warp and weft) of the same fabrics. The proposed equation was tested according to different fabric constructional parameters and reasonable results with the experimental data were obtained. The possibilities of general use of derived mathematical relations between theoretical and measured reflectance values were researched. The relation obtained was used to explain the effects of different constructional parameters on reflectance behavior of fabric surfaces.     

The effect of fabric balance and fabric cover on surface roughness of polyester fabrics

The effects of fabric balance and fabric cover on surface roughness values of textured polyester woven fabrics with different constructional parameters were investigated. The warp yarn properties (type, count and warp density) were kept constant while the effect of variation in weft yarn density and weave pattern were studied. Measurements were conducted on pre-treated white fabric samples and the results assessed in relation to their constructional properties. A general overview of the results showed that surface roughness values of polyester fabrics affected by fabric balance and fabric cover and the effects were related to fabric thickness, yarn densities, yarn crimp, positioning of yarns in fabric structure. A change in weave pattern from sateen to plain increased the fabric balance and fabric cover, but decreased the surface roughness. Similarly, an increase in weft density increased the fabric balance and fabric cover, but decreased surface roughness. In order to produce fabrics with smooth surface properties yarn density should be increased, yarn float lengths decreased, cover of fabrics increased and fabric balance improved.     

A comparative study of cotton knitted fabrics and garments produced by the modified low twist and conventional ring yarns

Spirality is one of the major potential problems in knitted fabrics and garments. It affects the aesthetics and physical properties of the garment produced, such as the seam displacement, shape retention, pattern distortion and sewing difficulties. In this paper, a comparative study has been carried out to evaluate the physical performance of 100 % cotton knitted fabrics and garments produced by the modified low twist and conventional ring yarns through the actual wearing and washing trials. Experimental results showed that the properties of side seam displacement, fabric spirality, dimensional stability and skewness change of the T-shirts and sweaters made by the modified single yarns are comparable to those of garments made from the control plied yarns but much improved when compared to those from the control single yarns. In addition, the pilling resistance and bursting strength of the knitted fabrics made by the modified single yarns can still maintain a reasonably high level at a low yarn twist.     

Assessment of the surface roughness of cotton fabrics through different yarn and fabric structural properties

The effects of some yarn properties (i.e. type, count, twist level, ply number, unevenness and crimp) and fabric constructional properties (i.e. cover, thickness and balance) on surface roughness values of cotton woven fabrics were investigated. A general overview of the results showed that surface roughness values of fabrics were affected from yarn and fabric properties and the effects were related to fabric balance, fabric cover (not cover factor), fabric thickness and crimp values of yarns in fabric structures. Surface roughness values of fabrics decreased as yarn fineness and yarn twist levels increased but as yarn ply number decreased. Also, surface roughness values gradually decreased from open-end yarn constituting fabrics to combed yarn constituting fabrics. Results showed that different properties of yarns caused changes in yarn crimps in fabric structure and also governed the changes in fabric balance, as well as changes in roughness of fabric surfaces. The changing properties of yarns and impact of these properties on fabric construction affected the formation of cotton fabric surfaces from smooth to coarse.     

Changing porosity of knitted structures by changing tightness

A geometrical model of plain knitted structures is discussed in depth to understand the yarn path in a knitted loop. A theoretical model has been created to predict the porosity of a knitted structure depending on the geometrical parameters, such as course spacing, wale spacing, stitch length, fabric thickness, count of yarn and fibre density. Polyester and nylon plain knitted fabrics were produced to different tightness, and porosity was determined by measuring the weight. The validity of the model was confirmed by experimental results, using different plain knit fabrics. The porosity of a knitted structure can be changed by reducing the yarn thickness and the stitch length; however this would influence the courses and wales per unit length in the structure.