The lamination influence on properties of agro-based particleboard

Abstract

Response surface methodology (RSM) based on a three-level, three-variable central composite rotatable design was applied to evaluate the effects of the parameters such as ratio of rice straw (Oryza sativa)/poplar (Populus deltoids) wood particle bonded with urea-formaldehyde resin in panels, species of wood veneer coating these panels and amount of adhesive in glue line on the modulus of rupture (MOR), internal bonding (IB), and thickness swelling (TS) of panels. Mathematical model equations were derived by computer simulation programming to optimize the properties of the particleboard. These equations that are second-order response functions representing MOR, IB, and TS were expressed as functions of three operating parameters of panel properties. Predicted values were found to be in a good agreement with experimental values (R ² values of 0.96, 0.98 and 0.98 for MOR, IB, and TS, respectively). This study has shown that the RSM could efficiently be applied for modeling panel properties. It was found that the variables affected the properties of panels. Straw usage up to 30% in the mixture did not cause a significant decrease in MOR, IB, and TS. Using beech veneer and 190 g/m² glue line had the highest MOR and lowest TS.     

Improvement on the properties of gypsum particleboard by adding cement

Gypsum particleboard (GPB) has high thickness swelling (TS), high water absorption (WA), and low mechanical properties compared with cement-bonded particleboard. The properties of GPB were improved by adding cement. The experimental results showed that GPB with the added cement had good physical and mechanical properties compared with those of gypsum particleboard with no added cement. The TS and WA of gypsum particleboard with added cement were reduced by 10%. The mechanical properties of GPB, such as internal bond strength (IB), modulus of rupture (MOR), and modulus of elasticity (MOE), increased when the GPB was made with added cement. The properties of GPB improved relative to the quantity of cement added. With an increase of cement content from 5% to 10%, the TS and WA were reduced, and the IB, MOR, and MOE were increased. In contrast, the TS and WA increased and the IB, MOE, and MOR decreased when the cement content was increased from 15% to 30%. Thus the physical and mechanical properties of GPB were successfully improved when the added cement content was 10%.An outline of this paper was presented at the 47th Annual Meeting of the Japan Wood Research Society in Kochi, April 1997     

Properties of kenaf core binderless particleboard reinforced with kenaf bast fiber-woven sheets

Kenaf composite panels were developed using kenaf bast fiber-woven sheets as top and bottom surfaces, and kenaf core particles as core material. During board manufacture, no binder was added to the core particles, while methylene diphenyldiisocyanate resin was sprayed to the kenaf bast fiber-woven sheet at 50 g/m² on a solids basis. The kenaf composite panels were made using a one-step steam-injection pressing method and a two-step pressing method (the particleboard is steam pressed first, followed by overlaying). Apart from the slightly higher thickness swelling (TS) values for the two-step panels when compared with the one-step panels, there was little difference in board properties between the two composite panel types. However, the two-step pressing operation is recommended when making high-density composite panels (>0.45 g/cm³) to avoid delamination. Compared with single-layer binderless particleboard, the bending strengths in dry and wet conditions, and the dimensional stability in the plane direction of composite panels were improved, especially at low densities. The kenaf composite panel recorded an internal bond strength (IB) value that was slightly low because of the decrease of core region density. The kenaf composite panel with a density of 0.45 g/cm³ (one-step) gave the mechanical properties of: dry modulus of rupture (MOR) 14.5 MPa, dry modulus of elasticity (MOE) 2.1 GPa, wet MOR 2.8 MPa, IB 0.27 MPa, TS 13.9%, and linear expansion 0.23%.     

Some of the properties of particleboard made from paulownia

The objective of this study was to determine some of the properties of experimental particleboard panels made from low-quality paulownia (Paulownia tomentosa). Chemical properties including holocellulose, cellulose, lignin contents, water solubility, and pH level of the wood were also analyzed. Three-layer experimental panels were manufactured with two density levels using urea–formaldehyde as a binder. Modulus of elasticity (MOE), modulus of rupture (MOR), internal bond strength (IB), screw-holding strength, thickness swelling, and surface roughness of the specimens were evaluated. Panels with densities of 0.65 g/cm³ and manufactured using a 7-min press time resulted in higher mechanical properties than those of made with densities of 0.55 g/cm³ and press times of 5 min. Based on the initial findings of this study, it appears that higher values of solubility and lignin content of the raw material contributed to better physical and mechanical properties of the experimental panels. All types of strength characteristics of the samples manufactured from underutilized low-quality paulownia wood met the minimum strength requirements of the European Standards for general uses.     

玻璃纤维束增强刨花板的研究

采用玻璃纤维束增强刨花板的试验结果表明,随着玻璃纤维束施加量的增加,刨花板的强度和刚度（ＭＯＲ和ＭＯＥ）有显著的提高,但施加量达到一定程度后,升高趋势逐渐平缓;随着玻璃纤维束间距的减小,刨花板的强度和刚度（ＭＯＲ和ＭＯＥ）呈直线上升,而内结合强度（ＩＢ）变化规律不明显,当间距小到一定程度后,ＩＢ很难达到德国室外用刨花板标准ＤＩＮ ６８７６３ Ｖ１００的要求;随着琉璃纤维束在刨花板厚度方向上的位置由     

喷蒸热压法棉秆无胶碎料板的研制

以棉秆为原料,采用喷蒸热压法研制无胶碎料板,探讨板的密度、蒸汽压力及喷蒸时间对棉秆无胶碎料板的物理力学性能的影响.结果表明:在试验范围内,随着板密度增大,无胶碎料板的静曲强度、弹性模量与内结合强度明显提高;提高蒸汽压力及延长喷蒸时间,能明显降低无胶碎料板的吸水厚度膨胀率.     

Cement-bonded particleboard with a mixture of wheat straw and poplar wood

We investigated the hydration behavior and some physical/mechanical properties of cement-bonded particleboard (CBPB) containing particles of wheat straw and poplar wood at various usage ratios and bonded with Portland cement mixed with different levels of inorganic additives. We determined the setting time and compression strength of cement pastes containing different additives and particles, and studied the effects of these additives and particles on thickness swelling, internal bond strength and modulus of rupture of CBPB by using RSM (Response Surface Methodology). The mathematical model equations (second-order response functions) were derived to optimize properties of CBPB by computer simulation programming. Predicted values were in agreement with experimental values (R2 values of 0.93, 0.96 and 0.96 for TS, IB and MOR, respectively). RSM can be efficiently applied to model panel properties. The variables can affect the properties of panels. The cement composites with bending strength > 12.5 MPa and internal bond strength > 0.28 MPa can be made by using wheat straw as a reinforcing material. Straw particle usage up to 11.5% in the mixture satisfies the minimum requirements of International Standard, EN 312 (2003) for IB and MOR. The dose of 4.95% calcium chloride, by weight of cement, can improve mechanical properties of the panels at the minimum requirement of EN 312. By increasing straw content from 0 to 30%, TS was reduced by increasing straw particle usage up to 1.5% and with 5.54% calcium chloride in the mixture, TS satisfied the EN 312 standard.     

Characterization of bagasse binderless particleboard manufactured in high-temperature range

This paper describes the features of binderless particleboard manufactured from sugarcane bagasse, under a high pressing temperature of 200–280 °C. Mechanical properties [i.e., modulus of rupture (MOR) and elasticity (MOE) in dry and wet conditions, internal bonding strength (IB)] and dimensional stability [i.e., thickness swelling (TS)] of the board were evaluated to investigate the effect of high pressing temperature. Recycled chip binderless particleboards were manufactured under the same conditions for comparison, and particleboards bonded with polymeric methylene diphenyl diisocyanate (PMDI) resin were manufactured as reference material. The target density was 0.8 g/cm³ for all of the boards. The results showed that the mechanical properties and dimensional stability of both types of binderless boards were improved by increasing the pressing temperature. Bagasse showed better performance than that of recycled chip as a raw material in all evaluations. Bagasse binderless particleboard manufactured at 260 °C had an MOE value of 3.5 GPa, which was equivalent to the PMDI particleboard, and a lower TS value of 3.7 % than that of PMDI particleboard. The MOR retention ratio under the dry and wet conditions was 87.0 %, while the ratio for the PMDI particleboard was only 54.6 %. The obtained results showed the possibility of manufacturing high-durability binderless particleboard, with good dimensional stability and water resistance, which previously were points of weakness for binderless boards. Manufacturing binderless boards under high temperature was effective even when using particles with poor contact area, and it was possible to express acceptable properties to allow the manufacture of particleboards. Further chemical analysis indicated a contribution of a saccharide in the bagasse to the improvement of the board properties.     

Investigation of a new natural adhesive composed of citric acid and sucrose for particleboard

The development of a natural adhesive composed of materials derived from non-fossil resources is a very important issue. In this study, only citric acid and sucrose were used as adhesive materials for particleboard. A water solution in which citric acid and sucrose were dissolved was used as an adhesive, and the manufacture of particleboard with a target density of 0.8 g/cm³ was attempted under a press condition of 200 °C for 10 min. The optimum mixture ratio of citric acid and sucrose and the optimum resin content was 25–75 and 30 wt%, respectively. The modulus of rupture (MOR) and the modulus of elasticity in bending were 20.6 MPa and 4.6 GPa, respectively. The internal bond strength (IB) was 1.6 MPa, indicating that the adhesive had excellent bond strength. The thickness swelling (TS) after water immersion for 24 h at 20 °C was 11.9 %. The board did not decompose even under more severe accelerated treatments. This meant that the adhesion had good water resistance. The MOR, IB and TS of the board were comparable to or higher than the requirement of the 18 type of JIS A 5908 (2003). Consequently, there is a possibility that a mixture of citric acid and sucrose can be used as a natural adhesive for particleboard.     

蔗髓含量对蔗渣碎料板性能的影响研究

研究了蔗髓含量（质量分数）分别在10%、20%、30%、40%4种不同情况下蔗渣碎料板的密度、静曲强度、弹性模量、内结合强度、吸水厚度膨胀率和板面握钉力等物理力学性能的变化规律.结果发现，随蔗髓含量的增加，板材的密度增加，弹性模量和板面握钉力下降；在蔗髓含量低于20%以下时，蔗髓的存在对板材的静曲强度无明显影响，而随蔗髓含量增加，吸水厚度膨胀率影响显著上升；在蔗髓含量高于20%以上时，蔗髓的含量增加使板材静曲强度明显下降，而对吸水厚度膨胀率无影响；蔗髓的含量对板材的内结合强度影响不明显.     

利用杨树人工林剩余物生产刨花板可行性研究

The composite board industry in Iran is obliged to use residues from forest operation as well as wood industry for competing with paper industry because of shortage of wood. In the present study we investigated the residues from poplar plantation used for particleboard production. Three kinds of wood materials, poplar branches, small diameter poplar wood (3–8 cm) and beech wood, were used in the experiment of particleboard production. The results demonstrated that the characteristic of particleboard made from poplar branches and small diameter wood is comparable to that made from mature beech wood. To avoid too much residual acid in the final board, the properties of boards produced with 1.5% hardener at 175°C press temperature are acceptable, although the properties of particleboard produced with 2% hardener were higher than were higher than that of the board produced with lower hardener (1% or 1.5%).. The MOR, MOE and IB of particleboard made from branches were measured as 14.57, 2015, and 1.32 MPa, respectively, while The MOR, MOE and IB of particleboard produced from small diameter poplar wood were 19.90, 2199, and 1.86 MPa, respectively. The thickness swelling of boards made from branches after 2 and 24 h immersion in water was 20.14% and 31.26%. The utilization of branches and very small diameter wood of poplar is recommended for the survival and developments of particleboard industry in Iran.     

Performance of samama (Anthocephalus macrophyllus) LVL based on veneer thickness,juvenile proportion and lay-up

ABSTRACT

A study to determine the quality of laminated veneer lumber (LVL) from samama wood (Anthocephalus macrophyllus) was carried out. Samama is a fast-growing endemic wood in eastern Indonesia. Factorial of three factors in RAL design was used to investigate the influence of veneer thickness, juvenile proportion and veneer lay-up to the quality of the resulted samama LVL. The veneer thicknesses were 1.5 and 3.0?mm. Juvenile proportions were arranged in five levels, which were 100% of juvenile veneer, 100% of mature veneer and combination of both juvenile and mature with juvenile proportion of 14%, 43% and 71%. Two veneer lay-up used in this study were loose side met loose side and tight side met loose side. The result of the study showed various specific gravity of LVL by different proportions of juvenile. This factor also affected the other physical traits. Shear strength of the LVL was equal to the solid wood, yet MOE and MOR were affected by juvenile proportion and veneer lay-up. LVL developed from 100% of mature veneer exhibited the highest MOE and MOR, yet no significant difference was noted in MOE and MOR between LVL 100% of juvenile and other tested juvenile proportions.     

Physical and Mechanical Properties of Flakeboard Reinforced with Bamboo Strips

The objective of this study was to investigate the physical and mechanical performance of flakeboard reinforced with bamboo strips. The study investigated three different bamboo strip alignment patterns and an experimental control. All panels were tested in static bending both along parallel and perpendicular to the lengths of the bamboo strips. Internal bond strength (IB), thickness swelling (TS), linear expansion (LE), and water absorption (WA) were also examined. As expected, modulus of rupture (MOR) and modulus of elasticity (MOE) were substantially greater for all three experimental panel types as compared to the control group. LE was also improved for all three experimental panel groups. The bamboo strip alignment patterns had no significant effect on TS, WA and IB. The sample means for MOR, MOE and LE tested perpendicular to the bamboo strip lengths yielded slightly lower mean values than corresponding samples tested parallel to the bamboo strips lengths. This difference in mechanical properties is largely attributed to low panel density in the failure zones.     

Effect of thermo-mechanical refining on properties of MDF made from black spruce bark

The effects of thermo-mechanical refining conditions on the properties of medium density fiberboard (MDF) made from black spruce (Picea mariana) bark were evaluated. The bark chips were refined in the MDF pilot plant of Forintek Canada Corporation under nine different refining conditions in which preheating retention time was adjusted from 3 to 5 to 7 min and steam pressure was set at either 0.6, 0.9 or 1.2 MPa. The resulting bark fibers were blended with 12% UF resin (based on oven-dry fiber weight) using a mechanical blender. The resinated fibers were manually formed into fiber mats and hot-pressed into MDF panels using consistent parameters. Two panels for each refining condition were produced, resulting in a total of 18 panels. Analysis of variance (ANOVA) was used to analyze the significance of factors. Regression coefficients and 3D contour plots were used to quantify the relationship between panel properties and the two test factors. The results from this study indicated that the preheating retention time was a significant factor for both modulus of rupture (MOR) and modulus of elasticity (MOE), the steam pressure was a significant factor for internal bond strength (IB), MOR and MOE, whereas both factors were insignificant for thickness swelling, water absorption and linear expansion. The properties of MDF panels were quadratic functions of retention time and steam pressure. Compared to the ANSI standard for 120-grade MDF, most panels with a nominal density of 950 kg/m³ had very high IB (>1 MPa) and acceptable MOR, MOE and dimension stabilities. These results suggest that black spruce bark residues can be considered as a potentially suitable raw material for manufacturing MDF products.     

木材-橡胶功能性复合材料制造工艺主要影响因素的交互作用和相关性(英文)

确定聚异氰酸酯(PMDI)与脲醛胶(UF)混合胶黏剂胶接木材与废旧轮胎橡胶制备功能性复合材料工艺的可行性;研究木材-橡胶功能性复合材料制备工艺的主要影响因素(密度、热压时间和温度)对复合材料力学性能:内结合强度(IB)、静曲强度(MOR)、弹性模量(MOE)作用的相关性。采用Design-Expert的响应曲面法分析各主要因子密度、温度、时间对力学性能影响的变化规律,优化各因子,并揭示相互影响和作用机制。结果表明:密度对材料的力学强度有显著性的影响,热压温度与时间的交互作用同样对材料的力学性能影响显著;采用低成本的PMDI/UF混合胶黏剂能够很好地胶结木材和橡胶制备功能性复合材料;获得木材-橡胶复合材料最佳优化工艺:密度1000kg·m-3、热压时间300s、热压温度170℃。利用电子扫描电镜(SEM)揭示了木材-橡胶功能性复合材料的微观结构,并进行界面结构分析。对PMDI/UF胶黏剂胶接橡胶和木材的物理化学胶合机制进行全面系统的分析。     

烟秆/木材刨花板的初步研究烟秆

初步探讨了实验室条件下烟秆/木材刨花板的生产工艺,研究了热压时间、施胶量、密度、木刨花加入量等因素对板材的静曲强度、内结合强度、吸水厚度膨胀率的影响.实验结果表明,烟秆/木材刨花板的静曲强度和吸水厚度膨胀率较纯烟秆刨花板有所提高,内结合强度相差不大.     

Effects of mat moisture content and press closing speed on the formation of density profile and properties of particleboard

Isocyanate resin-bonded 0.5 and 0.7 g/cm³ lauan (Shorea sp.) particleboards were produced from mats with uniform and distributed moisture content (MC) distributions, using three hot press closing speeds. The effects of these processing variables on the formation of density profile in particleboard and board properties were analyzed statistically. A definition of the density profile was introduced, and the correlations among the various defining factors were established. The results are summarized as follows. (1) The peak density (PD) of particleboard could be increased, with a slight reduction in the core density (CD), using mats with different MC distributions. (2) In a conventional density profile, CD and PD are highly dependent on the board mean density (MD); and the gradient factor (GF), peak distance from the faces (Pdi), and peak base (Pb) are significantly correlated to each other, at the 99% significance level. (3) Greater press closing speed reduces Pdi and Pb, with an increase in GF. (4) Greater press closing speed could increase the PD in board of low MD, with minimal effect on CD. (5) The modulus of elasticity (MOE) of particleboards from mats with high MC near the faces were consistently higher than those from mats with uniform MC, irrespective of the press closing speed, whereas their modulus of rupture (MOR) became indifferent at higher MD under slow and fast closing speeds. (6) Sanding does not improve the MOR and MOE of particleboard significantly.     

UF/PDMI组合胶黏剂在刨花板生产中的应用

采用脲醛树脂(UF)/聚合异氰酸酯(PDMI)组合胶黏剂,以不同的组合配比在较低热压温度(160℃)条件下用高含水率(9.0%)杂木刨花制备刨花板,检测其静曲强度、内结合强度以及2h和24h吸水厚度膨胀率。结果表明:聚合异氰酸酯(PDMI)的引入,可以显著提高刨花板的物理力学性能和耐水性能;将刨花终含水率提高至9.0%可节约刨花干燥能耗达13.0%以上;与脲醛树脂胶黏剂(UF)相比,使用PDMI/UF配比为1∶9的(10.0wt%PDMI)组合胶黏剂可以提高刨花板静曲强度80%,提高内结合强度150%;在不添加防水剂的条件下,可以将板材的2h吸水厚度膨胀率由31.0%提高至21.0%。该研究可为刨花板节能环保生产提供新思路。     

Development of binderless particleboard from kenaf core using steam-injection pressing

Binderless particleboards were successfully developed from kenaf core using the steam-injection press. The effects of board density, steam pressure, and treatment time on the properties of the board were evaluated. The target board densities were relatively low, ranging from 0.40 to 0.70g/cm³. The properties [i.e., moduli of rupture (MOR) and elasticity (MOE) in both dry and wet conditions, internal bonding strength (IB), and water absorption (WA)] of the boards increased linearly with increasing board density. Steam pressure and treatment time also affected the board properties. The bending strength and IB were improved with increased steam pressure. A long steam treatment time contributed to low thickness swelling (TS) values and thus better dimensional stability. The appropriate steam pressure was 1.0MPa, and the treatment time was 10–15min. The properties for 0.55g/cm³ density boards under optimum conditions were MOR 12.6MPa, MOE 2.5GPa, IB 0.49MPa, TS 7.5%, and wet MOR 2.4MPa. Compared with the requirement of JIS 5908, 1994 for particleboard, kenaf binderless boards showed excellent IB strength but relatively poor durability.Part of this report was presented at the 19th Annual Meeting of the Japan Wood Technological Association, Tokyo, October 2001     

Manufacture of Light-weight Composite Panel from Kenaf

Light-weight composite panels were manufactured using kenaf core particles as core material and kenaf bast fiber-woven sheets as top and bottom surfaces. Methylene diphenyldiisocyanate （MDI） resin was used as the adhesive with the resin content of 4% for core particles and 50 g/m^2 for bast fiberwoven sheets. The target board densities were set at 0.35.0.45 and 0.55 g/cm^3. The composite panels were evaluated With Japanese Industrial Standard for Particleboards （JIS A 5908- 2003）.The results show that the composite panel has high modulus of rupture and internal bonding strength. The properties of 0.45 g/cm^3 density composite panel are： MOR 20.4 MPa. MOE 1.94 MPa, IB 0.36 MPa, WA142%, TS 21%. Kenaf is a good raw material for making light-weight composite panels.