人工林杉木和杨树木材物理力学性质的株内变异研究

按照中国国家标准研究杉木和I-214杨树木材的抗弯弹性模量、抗弯强度、顺纹抗压强度和密度,同时按照日本国家标准研究2个树种的顺纹抗剪强度.结果表明:杉木的抗弯强度、顺纹抗压强度和密度由胸高直径处向上呈波浪形增加,抗弯弹性模量则稳定降低,但不同高度间杉木的物理力学性质没有显著差异;近树皮处木材的物理力学性质高于近髓心处木材,并有极显著差异.对于I-214杨树,只有抗弯弹性模量从髓心到树皮逐渐增加,其他的物理力学性质,最小值在从髓心到树皮的过渡区,最大值在近树皮处,从髓心到树皮,杨树的物理力学性质有极显著的差异.杉木和杨树的径面顺纹抗剪强度从髓心到树皮有极显著差异,并且近树皮的高于近髓心的木材,而弦面顺纹抗剪强度从髓心到树皮没有显著差异.木材密度与力学性质有很好的线性相关关系,木材密度是一个很好的力学强度的预测手段.     

32个杉木无性系木材密度和力学性质的变异*

３２个杉木无性系间，木材密度和抗弯弹性模量、抗弯强度、顺纹抗压强度均有较大差异，无性系内株间亦存在一定差异。木材密度与抗弯弹性模量、抗弯强度、顺纹抗压强度间的相关极显著，相关系数分别为０．３９５７、０．８３６８和０．９０２０；木材密度与生长速度呈负的遗传相关。     

人工林杉木木材力学性质对高温热处理条件变化的响应

以人工林杉木为试材,分别用空气和菜子油为介质,在温度为180,200和220 ℃对其分别热处理1,3和5 h,研究试材的抗弯强度(MOR)、抗弯弹性模量(MOE)、顺纹抗压强度、表面硬度对高温热处理条件变化的响应,同时对处理材的主要化学成分进行分析,用扫描电镜对处理材横切面微观结构进行观察.结果表明:人工林杉木试材的4种主要力学性质对不同条件热处理的响应程度不同.无论是空气热处理还是油热处理,试材的MOR,MOE,顺纹抗压强度与对照比有不同程度的降低,且随处理温度升高、时间延长,下降幅度增大,相比于时间,温度的影响更显著;180 ℃热处理1,3和5 h时,试材的MOR,MOE与对照比未发生明显变化(降幅在3%以内),而顺纹抗压强度则明显低于对照,两介质中降低幅度分别在3.29%～9.58%和3.89%～7.18%;200 ℃以上处理时,不同时间处理的3种主要力学性质不仅显著或极显著低于对照,且各性质问的差异也达显著或极显著水平;对硬度的测试结果表明:180 ℃热处理时,试件的径面硬度和弦面硬度均随时间的延长而增大;200 ℃热处理3 h时,试件的硬度达最大,与对照差异达显著水平;随后热处理试件的硬度开始降低,220 ℃热处理5 h后试件的硬度又明显低于对照.在隔氧的油介质中进行热处理,4种主要力学性质的变化程度低于空气介质处理材,当温度高于200 ℃时,两介质处理间的差异达显著水平.而热处理过程中木材主要化学组成与横切面微观结构变化的差异,反映了4种主要力学性质对不同条件热处理时表现出的响应差异.     

Static bending strength performances of cross-laminated woods made with five species

Thirty types of three-ply parallel- and cross-laminated woods were prepared from five species, and their static bending strength performance were investigated. The modulus of elasticity (MOE), proportional limit stress, and modulus of rupture (MOR) perpendicular to the grain were increased by cross-laminating, and the extent of the increase increased with decreasing density of the species. The measured values of MOE parallel and perpendi-cular to the grain of parallel-laminated woods and perpendicular to the grain of face laminae of cross-laminated woods were approximately equal to those calculated from true MOEs of individual laminae. However, the MOE parallel to the grain of face laminae of cross-laminated woods was much lower than the calculated MOE owing to the effect of the deflection caused by shear force on the MOE. The percentage of deflection caused by shear force versus total deflection (Y _s) showed high values, from 16.1% (buna) to 40.5% (sugi), and it decreased linearly with increasing shear modulus in the cross section of the core. In addition, there was an extremely high positive correlation between the MOR and the measured MOE parallel to the grain of face laminae of cross-laminated woods. The MOR was also highly dependent on the shear modulus in cross section of the core.Part of this paper was presented at the 50th Annual Meeting of the Japan Wood Research Society, Kyoto, April 2000     

ACQ和CuAz防腐处理对木材力学性能的影响

采用水溶性铜防腐剂(ACQ)和铜唑类防腐剂(CuAz)加压浸注处理臭冷杉木材,研究了药液处理浓度和后期干燥条件对木材抗弯弹性模量和抗弯强度的影响。t检验表明,本试验条件下,经两种防腐剂处理后,木材的抗弯弹性模量保持不变或略微增加。通过分析与对照素材试件的t检验比较,表明两种防腐剂处理前、后木材的抗弯弹性模量差异不显著。ACQ和CuAz防腐处理对木材抗弯强度有一定影响,ACQ处理使得木材抗弯强度整体上略有下降,而CuAz处理由于保持量相对较低,对木材抗弯强度未见明显下降趋势。后期干燥方式对木材抗弯强度亦未见明显规律性的影响。     

间伐强度对湿地松木材性质的影响规律研究

通过对不同间伐强度处理 (未间伐、弱度 (伐去株数 18 6 % )、中度 (伐去 35 7% )、强度 (伐去5 2 9% ) )的 19年生湿地松林分其林木木材的主要材性指标进行全面测试分析研究 ,结果表明 :间伐后 8a ,间伐强度对湿地松木材气干密度、全干密度、径向全干缩率、体积全干缩率、差异干缩、顺纹抗压强度、抗弯强度、弹性模量、径向抗剪强度及端面硬度有显著影响 ;随着间伐强度的增大 ,树干年生长轮平均宽度、木材差异干缩是增大的 ,而随间伐强度的增加木材气干密度、全干密度有不同程度的减小 ,木材顺纹抗压强度、抗弯强度、抗弯弹性模量、硬度等主要力学性质则是呈先增加后减小的趋势。     

Prediction of wood stiffness, strength, and shrinkage in juvenile wood of radiata pine

Development of optimal ways to predict juvenile wood stiffness, strength, and stability using wood properties that can be measured with relative ease and low cost is a priority for tree breeding and silviculture. Wood static modulus of elasticity (MOE), modulus of rupture (MOR), radial, tangential, and longitudinal shrinkage (RS, TS, LS), wood density (DEN), sound wave velocity (SWV), spiral grain (SLG), and microfibril angle (MFA) were measured on juvenile wood samples from lower stem sections in two radiata pine test plantations. Variation between inner (rings 1–2 from pith) and outer (rings 3–6 from pith) rings was generally larger than that among trees. MOE and MOR were lower (50%) in inner-rings than in outer-rings. RS and TS were higher (30–50%) for outer-rings than inner-rings, but LS decreased rapidly (>200%) from inner-rings to outer-rings. DEN had a higher correlation with MOR than with MOE, while MFA had a higher correlation with dry wood MOE than with MOR. SLG had higher significant correlation with MOE than with MOR. DEN and MOE had a weak, significant linear relationship with RS and TS, while MOE had a strong negative non-linear relationship with LS. Multiple regressions had a good potential as a method for predicting billet stiffness (R ² > 0.42), but had only a weak potential to predict wood strength and shrinkage (R ² < 0.22). For wood stiffness acoustic velocity measurements seemed to be the most practical, and for wood strength and stability acoustic velocity plus core density seemed to be the most practical measurements for predicting lower stem average in young trees.     

Quantitative Analysis on Measure Results by Resistograh for Wood Decay of Ancient Architecture

INTRODUCTION The main body of ancient architecture is wood construction in China, and the main bearing components of the buildings usually use timber, such as pillar, beam, purlin, crossbeam and rafter. Timber is a kind of biomaterial and will be damaged by fungal attack or insects after long time use, which will cause wood frames destroyed ultimately. Timber decay not only exists in its surface, but also usually begins with the inner of wood. It is therefore imperative to consider using …     

树冠特征对小黑杨木材性质和生长量的影响研究

以小黑杨人工林为对象,研究树冠特征对木材性质和生长量的影响.结果表明:树冠特征对木材基本密度影响不显著;对抗弯弹性模量(MOE)和顺纹抗压强度影响显著,对抗弯强度(MOR)影响不显著;对纤维长度、纤维宽度以及纤维长宽比影响不大;对胸高处湿心材、边材影响极显著.MOE、MOR和顺纹抗压强度与冠幅、冠长呈负相关.线性回归方程能较好地拟合顺纹抗压强度与冠幅的关系,R2值达到0.61;纤维长度、宽度与冠幅、冠长呈一定的正相关;湿心材面积、边材面积与冠幅、冠长呈高度正相关,边材面积与冠幅间存在密切的线性关系,方程的R2值达到0.78,二次多项式方程能很好地拟合湿心材面积与冠幅的关系,R2值为0.91.     

红松幼龄材与成熟材力学性质的差异

本文研究了人工林和天然林红松幼龄材与成熟材力学性质的差异.结果显示,成熟材的所有力学性质均高于幼龄材.幼龄材与成熟材的抗弯弹性模量差异在人工林红松中达0.01水平显著,天然林红松也达到0.01水平显著;人工林红松抗弯强度和弦向横纹抗压强度差异达0.05水平显著.抗弯强度、顺纹抗压强度、横切面硬度和弦向横纹抗压强度4项指标的差异达0.05水平显著.     

COMPARATIVE STUDY OF WOOD PROPERTIES BETWEENWHITE WOOD OF DAHURIAN LARCH AND MONGOLIANSCOTCH PINE

DahurianlarchandMongolianscotchpinearetwomajorconunerciaIconilbroustTeesinDaxing'anlingForesnyArea.Itisob-viousthattbcwoodproPertiesandworkability'ofthetWoplantsarecompletelydifferent.Butlnrecert'years,ltlsfoundthattherearetwodiffer':nttypesinparameterofwood'scolour.phy'sicalandmechanicalproPertiesandwork-ability'inDahurianlarch,namelyredwoodandx"hite..od.l']Andthepropertiesofwhite`voodaresligl1tlyyellow-white,medianweightandhardness,goodinworkability'andLard-ness,goodinwodability'anduneas…     

林地土壤类型对毛白杨木材性质的影响

本文对林地土壤对毛白杨木材性质影响的研究进行了综述。结果表明，水肥作用较好的夹淤沙壤质黄潮土生长的毛白杨木材纤维长度、宽度及全干缩率略大于通体沙壤质黄潮土的毛白杨，而前者的木材纤维长宽比、微纤丝角、气干密度、基本密度、抗弯弹性模量、抗弯强度和顺纹抗压强度略低于后者；木材pH值随土壤pH值的增加而减少，心、边材pH值匀呈酸性，且心材酸性强于边材；碱缓冲容量和总缓冲容量心材大于边材；酸缓冲容量心、边材差异很少；通体沙壤质黄潮土生长的毛白杨木材pH高于夹淤沙壤质黄潮土生长的毛白杨材，尤其边材差异更大；而土壤类型对木材的酸碱和总缓冲容量的影响甚微。方差分析，除木材密度、微纤丝角差异达到显著水平外，其它各项指标差异均不显著。     

湿地松与马尾松人工林木材物理力学性质的比较研究

通过对湿地松和马尾松人工林木材物理力学性质的测定和比较分析,结果表明:湿地松人工林木材密度、干缩系数和除冲击韧性以外的力学强度均稍大于马尾松人工林木材,而冲击韧性则恰恰相反.经差异显著性t检验表明:湿地松和马尾松木材物理力学性质指标中顺纹抗压强度、抗弯强度、弦面顺纹抗剪强度和冲击韧性差异极显著,气干密度、基本密度、径面顺纹抗剪强度和端面硬度差异显著,除此之外的其余指标差异不显著.     

稻壳形态对稻壳--木材复合材料性能的影响

测试了稻壳形态对稻壳-木材复合材料物理力学性能的影响。试验结果表明，以20网日、30网日和40网目的稻壳为补充材料制备的密度为0．80g／cm^3的板的物理力学性能均达到国标二级品的要求。确立20网目的稻壳适宜于稻壳-木材复合材料。     

不同因素对竹/木复合强化单板层积材MOE、MOR的影响

以杨木单板和竹帘为原料,采用低分子量水溶性酚醛树脂浸渍处理,通过干燥、组坯、热压等工艺制备竹木复合强化单板层积材。探讨了组坯方式、压缩率、热压温度、热压时间4个因素对竹木复合强化单板层积材弹性模量(MOE)和静曲强度(MOR)的影响。结果表明:表层为一层竹帘的竹木复合强化单板层积材的MOE和MOR较大,分别是13．43GPa、148．13MPa,与表层为杨木单板次表层为竹帘组坯方式相比分别增加了33．63％、56．16％。确定了竹木复合强化单板层积材较合理的制造工艺参数。     

The effects of thinning treatments on density, MOE, MOR and maximum crushing strength of Pinus brutia Ten. wood

The purpose of this study was to determine the effects of plantation thinning on various wood properties of Pinus brutia Ten. Tree samples were obtained from heavily and moderately thinned and unthinned 33–35 year-old plantations. Wood properties were examined in various wood zones including 16 annual rings after the first treatment. The results of this study showed that there was a significant relationship between thinning intensity and radial increment (1.30 m) for an individual tree. Thinning treatments increased annual ring width especially a few years after thinning. Heavy thinning treatments were especially effective in impacting mean ring width values at breast height. However, the percentage of late wood did not differ much between the samples. Based on the results of correlation analysis between ring width and late wood percentage there was no significant correlation identified. Mean wood density was not affected by the treatments. Also, no significant correlation was found between thinning and examined strength properties (MOR, MOE and compression strength parallel to grain). However, a relationship was found between wood density and all strength properties except for MOE. The current results suggest that thinning can produce improvements in ring width without any negative impacts on investigated wood properties. It is recommended that subsequent studies should be designed to understand genetic effects and maximize treatment effects.     

热处理对木材力学性能的影响综述

热处理可有效提高木材尺寸稳定性,同时对木材力学性能也有明显的影响。文中按照力学指标分别综述热处理工艺对静曲强度/弹性模量、抗压强度、脆性/冲击韧性及其他力学性能的影响,进而总结热处理对木材力学性能影响机理的研究进展;提出可以从以下方面深化热处理技术的研发:一是热处理技术研发时宜根据应用领域科学选择合适的力学指标,二是进一步拓展热处理介质以控制力学性能损失,三是进一步探索热处理对木材不同力学指标的影响机理。     

Indented rings (hazel growth) of Norway spruce reduce anisotropy of mechanical properties

This study presents three-point bending test results of Norway spruce clear wood specimens loaded on the radial-longitudinal plane in two different load cases. The tested samples were graded as resonance wood for instrument making and were characterised by narrow annual rings and relatively low density. The modulus of elasticity (MOE) and the corresponding modulus of rupture (MOR) are illustrated separately for the samples with straight grain and the group showing the specific growth pattern of indented rings (‘hazel growth’). With the longitudinal wood anatomical direction parallel to span width, the fibre deviation caused by the indents reduces MOE and MOR values, whereas a ‘reinforcing’ effect of the indents could be observed for the load case with span width parallel to the radial direction. Both aspects lead to a reduction in anisotropy for hazel-growth Norway spruce (anisotropy MOE: indented rings 11.6, straight grain 14.7, anisotropy MOR: indented rings 6.9, straight grain 8.9), which partly explains the exceptional position of this growth pattern for the construction of high-class musical instruments with outstanding mechanical and acoustical performance.     

炭化木物理力学性能的研究

以速生杉木为原料制备炭化木,主要研究了炭化工艺条件对炭化木(又称热处理木)物理力学性能的影响。研究表明:当热处理温度由常温增加至220℃时,炭化木材色逐渐变深,含水率逐渐降低,由13.40%降至4.89%,吸水性能较大幅度降低,由未处理素材的1.616%降至0.879%,同时密度由未处理素材的0.368g/cm~3减小至0.326 g/cm~3,静曲强度下降约25%左右,弹性模量先增加后减小,减小量约4%左右,冲击韧性也先增加后减小,减小量约42%左右,受热处理条件影响程度较大,而且木材干缩和湿胀系数明显下降,较大程度提高了木材的尺寸稳定性。     

Characterization of major,unused, and unvalued Indonesian wood species I. Dependencies of mechanical properties in transverse direction on the changes of moisture content and/or temperature

Mechanical property changes due to the moisture content (MC) and/or temperature changes were examined for 15 Indonesian wood species. A static bending test was carried out at 20°C, 65% relative humidity (air-dry), and water-saturated at 20°C (wet-20) and 80°C (wet-80). For individual test conditions, modulus of elasticity (MOE) and modulus of rupture (MOR) increased linearly with specific gravity regardless of wood species; however, maximum deflection did not correlate with specific gravity for any MC or temperature conditions. The relative values of MOE and MOR measured in wet-20 to air-dry conditions were variously affected from slightly to strongly depending on the wood species. However, the relative values always decreased markedly when saturated in water at 80°C, regardless of wood species. The relative MOE, MOR, and maximum deflection values due to the change in MC or MC and temperature combined were independent of specific gravity but may be dependent on wood type: softwood or hardwood.