Dynamic modulus of elasticity and bending properties of young Taiwania trees grown with different thinning and pruning treatments

The effects of different thinning and pruning methods on the bending strength and dynamic modulus of elasticity (DMOE) of young Taiwania (Taiwania cryptomerioides Hay) were investigated. The average DMOE, modulus of elasticity (MOE), and modulus of rupture (MOR) in the thinning treatments showed the following trend: no thinning > medium thinning > heavy thinning. This indicates that thinning reduces average bending properties. The average DMOE, MOE, and MOR in the pruning treatments showed the following trend: medium pruning > no pruning > heavy pruning. According to this tendency, better average qualities of lumber and specimens were from wood subjected to no-thinning and medium-pruning treatments according to an ultrasonic wave technique and static bending tests. However, most results showed no statistically significant differences among thinning, pruning, and thinning and pruning treatments. The average values of DMOE, MOE, and MOR of visually graded construction-grade lumber were significantly greater than those of below-grade lumber. Moreover, there were very significant positive relationships between density, ultrasonic velocity, DMOE, MOE, and MOR, although the determination coefficients were small.     

Impact of precommercial thinning on tree growth,lumber recovery and lumber quality in Abies balsamea

Abstract

Precommercial thinning (PCT) is often used to improve stand growth and value. While PCT may accelerate tree growth and reduce mortality, it may also have a negative effect on product quality. This study examined the effect of moderate and heavy thinning on tree growth, lumber recovery and quality in a natural balsam fir [Abies balsamea (L.) Mill.] PCT trial 35 years after thinning. Compared with the control, the heavy thinning increased merchantable tree diameter, stem volume per tree and lumber volume recovery per tree by 41.1%, 100.9% and 92.7%, respectively, reduced the Select Structural grade (the best grade) recovery by 33.7%. Thinning did not affect the no. 2 and better grade yield. There was a 12.2% and 15.0% difference, respectively, in the lumber bending modulus of elasticity (MOE) and modulus of rupture (MOR) between the control and heavy thinning. Moderate thinning had little impact on the visual grade recovery, lumber bending MOE and MOR. Heavy thinning is recommended if the goal is to get sizeable sawlogs in the shortest time, whereas moderate thinning is preferable if the intention is to minimize the negative effects on lumber quality while retaining modest tree growth and lumber recovery. Overall, PCT of very dense young balsam fir stands appears to be an effective and viable silvicultural treatment.     

The variation of microfibril angle in South African grown Pinus patula and its influence on the stiffness of structural lumber

Reduction in the rotation ages of softwood saw-log plantations in South Africa is causing increased proportions of low stiffness sawn lumber at final harvest. It has been shown for some species that the microfibril angle (MFA) of the S2 layer of tracheids is strongly related to the modulus of elasticity (MOE) of wood, even more so than wood density, especially in wood formed during juvenile growth. The objectives of this study were to describe the variation in MFA in young Pinus patula trees and to determine the relationship between MFA and the dynamic MOE of sawn P. patula lumber. Thirty 16- to 20-year-old trees from six compartments from the Mpumalanga escarpment were processed into discs and lumber. The MFA, density and ring width were measured at two height levels using Silviscan 3. The average annual ring MFA varied between 7° and 29°; the pattern of variation depended mainly on height level and the ring number from the pith. The MFA in P. patula followed the same within-tree variation trends as in New Zealand-grown Pinus radiata but the average MFA was lower in absolute terms and differences between height levels were less pronounced. The MFA and density exhibited highly significant Pearson correlations of 0.73 and 0.70, respectively, with board dynamic MOE. A multiple regression model, which included MFA, density and ring width, explained 71% of the variation in the dynamic MOE of boards. A sensitivity analysis on the model showed that MFA and density had approximately similar influences on predicting the dynamic MOE of Pinus patula boards.     

Assessment of flexural properties of different grade dimension lumber by ultrasonic technique

The dimension lumber （45mm×90mm×3700mm） of plantation Chinese fir （Cunninghamia lanceolata （Lamb.） Hook.） was graded to four different classes as SS, No. 1, No.2 and No.3, according to national lumber grades authority （NLGA） for structure light framing and structure joists and planks. The properties of apparent density was determined at 15% moisture content, bending strength and stiffness were tested according to American Society for Testing and Materials （ASTM） D198-99, and dynamic modulus of elasticity （Eusw） was measured by ultrasonic technique, for predicting the flexural properties of different grade lumbers. The results showed that Eosw was larger than the static MOE. The relationship between Eusw and static MOE was significant at 0.01 level, and the determination coefficients （R2） of the four grade lumbers followed the sequence as R^2No.2 （0.616）〉 R^2ss （0.567）〉 R^2No1 （0.366）〉 R^2No.3 （0.137）. The R^2 of Fusw and MOR were lower than that of the Etru and MOR for each grade. The Eusw of all the grade lumbers, except No.3-grade, had significant correlation with the static MOE and MOR, thus the bending strengthof those grade lumbers can be estimated by the E The Etru valuesof four grade lumbers followed a sequence as No.2-grade （10.701 GPa） 〉 SS-grade （10.359 GPa） 〉 No.l-grade （9.840 GPa） 〉 No.3-grade （9.554 GPa）. For the same grade dimension lumber, its Eusw value was larger than static MOE. Mean values of MOR for four grade lumbers follow a sequence as No.2-grade （48.67 MPa） 〉 SS-grade （48.16 MPa） 〉 No.3-grade （46.55 MPa） 〉 No. 1-grade （43.39MPa）.     

超声波预测落叶松规格材的抗弯性能

用超声波法测量落叶松规格材的动态弹性模量(DMOE),用弯曲试验测量其静态抗弯弹性模量(MOE)和抗弯强度(MOR),分析DMOE与MOE和MOR的相关性。研究结果表明:落叶松规格材的DMOE值比MOE高;DMOE与MOE和MOR的相关性均在0.01水平显著,DMOE与MOE的相关性高于DMOE与MOR的相关性。     

Mechanical properties assessment of Cunninghamia lanceolata plantation wood with three acoustic-based nondestructive methods

The objectives of this study were to establish the method of evaluating wood mechanical properties by acoustic nondestructive testing at standing trees and at logs of a Chinese fir (Cunninghamia lanceolata (Lamb.) Hook.) plantation, and to compare three acoustic nondestructive methods for evaluating the static bending modulus of elasticity (MOE), modulus of rupture (MOR), and compressive strength parallel-to-grain (σ_c) of plantation wood as well. Fifteen Chinese fir plantation trees at 36 years of age were selected. Each tree was cut into four logs, for which three values of dynamic modulus of elasticity, i.e., E _sw, of the north and south face based on stress waves to assume the measuring state of the standing tree, E _fr, longitudinal vibration, and E _us, ultrasonic wave, were measured in the green condition. After log measurements, small specimens were cut and air-dried to 12% moisture content (MC). Static bending tests were then performed to determine the bending MOE and MOR, and compressive tests parallel-to-grain were made to determine σ_c. The bending MOE of small clear specimens was about 7.1% and 15.4% less than E _sw and E _us, respectively, and 11.3% greater than E _fr. The differences between the bending MOE and dynamic MOE of logs as determined by the three acoustic methods were statistically significant (P < 0.001). Good correlation (R = 0.77, 0.57, and 0.45) between E _sw, E _fr, and E _us and static MOE, respectively, were obtained (P < 0.001). It can be concluded that longitudinal vibration may be the most precise and reliable technique to evaluate the mechanical properties of logs among these three acoustic nondestructive methods. Moreover, the results indicate that stress wave technology would be effective to evaluate wood mechanical properties both from logs and from the standing tree.     

Evaluation of Strength Performance of Finger-jointed Lumbers Using Three Kinds of Nondestructive Techniques

Resonance flexural vibration（Fast Fourier Transform, FFT）, ultrasonic wave（Pundit） and stress wave（Metriguard） techniques were examined as means of evaluating the static modulus of elasticity （MOE） and predicting the modulus of rupture （MOR） of finger-jointed lumber specimens made with four kinds of Eucalyptus （Eucalyptus. citriodora, E. exserta, E. grandis x E. urophylla and E. grandis）. Dynamic MOE was calculated from frequency and time obtained from forced vibrations and sounds induced in the four species of finger-jointed specimens. It was found that correlation coefficients between density and static MOE and dynamic MOE were statistically significant at the 0.01 level. And it was also found that the three nondestructive techniques can provide rapid and accurate means to determine the MOE, and the dynamic MOE was more accurate to predict static MOE than density. But the correlation coefficient between dynamic MOE, static MOE and MOR were lower than results reported by other researchers for solid wood, and were not statistically significant. It can be concluded that the three nondestructive techniques are useful for evaluating the MOE, but not suitable for predicting the MOR of finger-jointed.     

An investigation of the influence of selected factors on the properties of spruce wood

Thirty Norway spruce trees (Picea abies (L.) Karst.) from the forest district of the ETH Zurich were tested for bending MOR, static MOE of bending and dynamic MOE (calculated from eigenfrequency and sound velocity). The specimens were clear and were sampled from the whole of the stem. Their correlations to density, annual ring width, height in the tree, distribution over the stem diameter and the percentage of compression wood were statistically analysed. All three elasticity modules and the maximal stress can be very well predicted from a linear function of the sample density with a common gradient across the compression wood values but with different intercepts that decrease with increasing compression wood content. The other variables have highly significant impacts on the response variables too, however, this is largely irrelevant for the goodness of fit. Further, a clear increase of density, of MOE and of bending MOR was measured from pith to bark and similarly with decreasing annual ring width. Concerning the height of the stem, no distinct trend for the mechanical properties could be found.     

Indented rings (hazel growth) of Norway spruce reduce anisotropy of mechanical properties

This study presents three-point bending test results of Norway spruce clear wood specimens loaded on the radial-longitudinal plane in two different load cases. The tested samples were graded as resonance wood for instrument making and were characterised by narrow annual rings and relatively low density. The modulus of elasticity (MOE) and the corresponding modulus of rupture (MOR) are illustrated separately for the samples with straight grain and the group showing the specific growth pattern of indented rings (‘hazel growth’). With the longitudinal wood anatomical direction parallel to span width, the fibre deviation caused by the indents reduces MOE and MOR values, whereas a ‘reinforcing’ effect of the indents could be observed for the load case with span width parallel to the radial direction. Both aspects lead to a reduction in anisotropy for hazel-growth Norway spruce (anisotropy MOE: indented rings 11.6, straight grain 14.7, anisotropy MOR: indented rings 6.9, straight grain 8.9), which partly explains the exceptional position of this growth pattern for the construction of high-class musical instruments with outstanding mechanical and acoustical performance.     

Variation in wood properties among five full-sib families of Norway spruce (Picea abies)

Genetic- and environmental variation and correlation patterns were characterized for modulus of elasticity (MOE), modulus of rupture (MOR) and related wood traits: latewood proportion, wood density, spiral grain, microfibril angle and lignin content in five full-sib families of Norway spruce. The families were evaluated on the basis of clearwood specimens from the juvenile -mature wood transition zone of 93 sampled trees at age 30 year from seed. Family-means varied significantly (p < 0.05) for all wood traits studied except lignin content. MOE varied between 7.9–14.1 GPa among trees and 9.4–11.0 GPa among families. MOR varied between 47–87 MPa among trees and 61–71 MPa among families. Families remained significantly different in an analysis of specific MOE (MOE/density) and MOR (MOR/density). Hence, solely relying on wood density as a wood quality trait in tree breeding would not fully yield the potential genetic gain for MOE and MOR. Correlations between wood structural traits and specific MOE and MOR are presented and discussed.     

干燥方法对毛白杨木材力学性质的影响

分别采用气干、常规干燥及高温干燥方法,对毛白杨木材进行干燥,并检测分析3种干燥方法对毛白杨木材的抗弯弹性模量(MOE)、抗弯强度(MOR)、冲击韧性及硬度等力学性质的影响.结果表明,3种干燥方法对MOE及MOR无显著影响,但高温干燥时木材的冲击韧性及表面硬度有较大的影响.     

Flexural and visual characteristics of fibre-managed plantation Eucalyptus globulus timber

ABSTRACT

The main goal of this study was to investigate the visual characteristics, recovery rate, and flexural properties of sawn boards from a fibre-managed plantation Eucalyptus globulus resource as a potential raw material for structural building applications. The impacts of the visual characteristics, strength-reducing features, and variation in basic density and moisture content on the bending modulus of elasticity (MOE) and modulus of rupture (MOR) of the boards were investigated. The reliabilities of different non-destructive methods in predicting MOE and MOR of the boards were evaluated, including log acoustic wave velocity measurement and numerical modellings. The MOE and MOR of the boards were significantly affected by the slope of grain, percentage of clear wood, and total number of knots in the loading zone of the boards. The normal variation in basic density significantly influenced the MOE of the boards while its effect on the MOR was insignificant. The numerical models developed using the artificial neural network (ANN) showed better accuracies in predicting the MOE and MOR of the boards than traditional multi-regression modelling and log acoustic wave velocity measurement. The ANN models developed in this study showed more than 78.5% and 79.9% success in predicting the adjusted MOE and MOR of the boards, respectively.     

Fresh-stem bending of silver fir and Norway spruce

The bending and growth characteristics of large fresh stems from four silver fir (Abies alba Mill.) and three Norway spruce (Picea abies (L.) Karst.) trees were studied. Twenty logs taken from different stem heights were subjected to four-point bending tests. From the bending test records, we calculated stress-strain curves, which accounted for detailed log taper, shear deformation and self weight. From these curves we determined, among other parameters, the modulus of elasticity (MOE), the modulus of rupture (MOR) and the work absorbed in bending (W). No significant differences were found between species for the wood properties examined. Values of MOE, MOR and W generally decreased with stem height, with MOR in the range of 43 to 59 MPa and MOE ranging from 10.6 to 15.6 GPa. These MOE values are twice or more those reported for stems of young Sitka spruce (Picea sitchensis (Bong.) Carr.) trees. Based on the radial growth properties measured in discs from the logs, we calculated predicted values of MOE and MOR for the stem cross section. The predictions of MOE were precise, whereas those of MOR were approximate because of a complex combination of different failure mechanisms. Methods to test and calculate MOE, MOR and W for the stems of living trees are discussed with the aim of improving analyses of tree biomechanics and assessments of forest stability protection.     

杉木积成材竹片贴面工艺探讨

对杉木积成材进行了竹片贴面的初步试验，结果表明：杉木积成材进行竹片贴面切实可行；竹片贴面后的杉木积成材密腹略高于基材；竹片与基材之间的胶合强度大于基材内部的胶合强度；贴面板的MOR和MOE高于基材：24h吸水厚度膨胀率佟明显低于基材。     

木束条尺寸对杉木积成材性能的影响研究

为了探索较佳的木束条尺寸,以提高杉木积成材的质量,研究了不同尺寸的杉木木束条对杉木积成材性能的影响规律,结果表明:木束条的长度对杉木积成材的纵向静曲强度、弹性模量、24h吸水厚度膨胀率有较大的影响;木束条的厚度对杉木积成材纵向静曲强度、弹性模量的影响不大,但对24h吸水厚度膨胀率、内结合强度有较大的影响;木束条的宽度对杉木积成材的物理力学性能影响极小,不存在统计意义上的影响;木束条的较佳尺寸为:长度120 mm,宽度4mm,厚度2.5 mm.     

Wood properties and their among-family variations in 10 open-pollinated families of Picea jezoensis

This study aimed to evaluate radial and among-family variations of wood properties in Picea jezoensis. A total of 174 trees were randomly selected from 10 open-pollinated families in a progeny trial for measuring stem diameter, dynamic Young’s modulus of log (DMOE_log), annual ring width (ARW), air-dry density (AD), modulus of elasticity (MOE), and modulus of rupture (MOR). Mean values of DMOE_log, AD, MOE, and MOR were 9.60 GPa, 0.41 g/cm³, 9.44 GPa, and 76.6 MPa, respectively. Significant differences among families were observed in all properties. F values obtained by analyzing variance in wood properties were higher than those generally observed in growth traits. In addition, F values in wood properties remained relatively higher from the 1st to 25th annual ring from the pith, although F value in ARW rapidly decreased with each increase in annual ring number. These results indicate that genetic factors largely contributed to the variance in wood properties compared with the growth traits.     

杉木热处理材结晶度及力学性能的研究

热处理对木材力学性能的影响是多样的,这与热处理条件下木材的物理化学变化密切相关。本次研究将杉木板材在160℃、180℃和220℃常压蒸汽条件下进行热处理,考察处理材的结晶度、抗弯弹性模量、抗弯强度及相互可能的关联。结果表明,热处理使试材结晶度增加,有助于提高木材的刚性,使热处理材的抗弯弹性模量高于常规对照材;结晶度的提高对抗弯强度没有改善作用,热处理后试材的抗弯强度明显下降。     

Fresh-wood bending: linking the mechanical and growth properties of a Norway spruce stem

To provide data and methods for analyzing stem mechanics, we investigated bending, density and growth characteristics of 207 specimens of fresh wood from different heights and radial positions of the stem of one mature Norway spruce (Picea abies L. Karst.) tree. From the shape of each stress-strain curve, which was calculated from bending tests that accounted for shear deformation, we determined the modulus of elasticity (MOE), the modulus of rupture (MOR), the completeness of the material, an idealized stress-strain curve and the work involved in bending. In general, all mechanical properties increased with distance from the pith, with values in the ranges of 5.7-18 GPa for MOE, 23-90 MPa for MOR and 370-630 and 430-1100 kg m(-3) for dry and fresh wood densities, respectively. The first three properties generally decreased with stem height, whereas fresh wood density increased. Multiple regression equations were calculated, relating MOR, MOE and dry wood density to growth properties. We applied these equations to the growth of the entire stem and considered the annual rings as superimposed cylindrical shells, resulting in stem-section values of MOE, MOR and dry and fresh densities as a function of stem height and cambial age. The standing tree exhibits an inner stem structure that is well designed for bending, especially at a mature stage.     

Radial and between-family variations of the microfibril angle and the relationships with bending properties in Picea jezoensis families

With emphasis on tree breeding for wood quality in Picea jezoensis, we aimed to evaluate radial and between-family variations in the microfibril angle (MFA) of the S₂ layer in the latewood tracheids in 10 open-pollinated families of 43-year-old P. jezoensis trees. In addition, the relationships between MFA/wood density with the modulus of elasticity (MOE) or modulus of rupture (MOR) were investigated. Significant differences in MFA between families were found from the pith toward the bark. MFA showed higher values around the pith area, although some families showed relatively lower values than others around this area. In addition, due to a larger coefficient of variations of MFA near the pith, the potential for juvenile wood MFA improvement may be greater compared with mature wood. MOE was correlated with MFA in juvenile wood and with wood density in mature wood, whereas MOR was mainly correlated with wood density at radial positions in both woods. Therefore, to improve the MOE and MOR of P. jezoensis wood, both MFA and wood density would be factors to consider in both juvenile and mature woods. On the other hand, there are indications that, only wood density would be an important criterion for improving mature wood properties.     

32个杉木无性系木材密度和力学性质的变异*

３２个杉木无性系间，木材密度和抗弯弹性模量、抗弯强度、顺纹抗压强度均有较大差异，无性系内株间亦存在一定差异。木材密度与抗弯弹性模量、抗弯强度、顺纹抗压强度间的相关极显著，相关系数分别为０．３９５７、０．８３６８和０．９０２０；木材密度与生长速度呈负的遗传相关。