Sorption-desorption of aminocyclopyrachlor in selected Brazilian soils

Aminocyclopyrachlor sorption/desorption was investigated in 14 soils from Brazil, representing a range of pH, and organic carbon (OC) and clay contents. The Freundlich equation adequately described behavior of aminocyclopyrachlor in soil. Freundlich sorption coefficient (K(f)) values ranged from 0.06 to 1.64 and 1/n values for ranged from 0.9 to 1.0. Sorption was correlated to OC (K(f,oc) ranged from 11 to 64) and clay contents. The lowest sorption was found for soils with very low OC contents (0.50-0.65%) and loamy-sand to sand textures. The 1/n values for desorption were lower than those observed for sorption, suggesting that aminocyclopyrachlor sorption by soil was not reversible; hysteresis coefficients ranged from 0.13 to 0.74. The results suggest that although aminocyclopyrachlor would be very mobile based on its sorption coefficients, its potential depth of leaching may be overestimated due to the hysteretic desorption.     

Effect of liming on hexazinone sorption and desorption behavior in various soils

Liming is a practice commonly used to modify soil acidity, neutralize aluminum, and increase calcium and magnesium in the soil. Liming can change herbicide retention processes and consequently weed control and potential environmental contamination. The effects of liming on the sorption and desorption of hexazinone in different soils were evaluated. Samples from seven Brazilian soils were collected and separated into two subsamples, with and without limestone incubation. Hexazinone was quantified using ultra high-performance liquid chromatography. The sorption and desorption coefficients were determined in soils using Freundlich isotherms. Increasing the pH did not alter the sorption kinetics of hexazinone in the same soil class. The shortest sorption time of hexazinone occurred in soils with higher organic matter (OM) and clay content. Liming reduced the sorption and increased the desorption of hexazinone in the soils, which was caused by the increase in pH and reduction of OM content. Although the application of limestone increased desorption, the rate at which this process occurred was less than the sorption rate of hexazinone in most cases. In alkaline soils, the recommended dose of hexazinone for pre-emergence application should be low to avoid leaching and reduce the contamination of groundwater resources.     

Adsorption and Desorption of Copper in Pasture Soils

Abstract

Copper (Cu) is bound strongly to organic matter, oxides of iron (Fe) and manganese (Mn), and clay minerals in soils. To investigate the relative contribution of different soil components in the sorption of Cu, sorption was measured after the removal of various other soil components; organic matter and aluminum (Al) and Fe oxides are important in Cu adsorption. Both adsorption and desorption of Cu at various pH values were also measured by using diverse pasture soils. The differences in the sorption of Cu between the soils are attributed to the differences in the chemical characteristics of the soils. Copper sorption, as measured by the Freundlich equation sorption constants [potassium (K) and nitrogen (N)], was strongly correlated with soil properties, such as silt content, organic carbon, and soil pH. The relative importance of organic matter and oxides on Cu adsorption decreased and increased, respectively, with increasing solution Cu concentrations. In all soils, Cu sorption increased with increasing pH, but the solution Cu concentration decreased with increasing soil pH. The cumulative amounts of native and added soil Cu desorbed from two contrasting soils (Manawatu and Ngamoka) during desorption periods showed that the differences in the desorbability of Cu were a result of differences in the physico‐chemical properties of the soil matrix. This finding suggests that soil organic matter complexes of Cu added through fertilizer, resulted in decreased desorption. The proportions of added Cu desorbed during 10 desorption periods were low, ranging from 2.5% in the 24‐h to 6% in the 2‐h desorption periods. The desorption of Cu decreased with increasing soil pH. The irreversible retention of Cu might be the result of complex formation with Cu at high pH.     

Sorption and desorption of triadimefon by soils and model soil colloids

Sorption-desorption of the azole fungicide triadimefon [1-(4-chlorophenoxy)-3,3-dimethyl-1-(1H-1,2, 4-triazol-1-yl)-2-butanone] on eight soils and a series of single, binary, and ternary model soil colloids was determined using the batch equilibration technique. Regression analysis between Freundlich sorption coefficients (K(f)) and soil properties suggested that both clay and organic C (OC) were important in triadimefon sorption by soils, with increasing importance of clay for soils with high clay and relatively low OC contents. Triadimefon sorption coefficients on soil were not significantly affected by the concentration of electrolyte or the presence of soluble soil material in solution, but they were highly dependent on the soil:solution ratio due to the nonlinearity of triadimefon sorption on soil. Freundlich sorption isotherms slopes were very similar for all soils (0.75 +/- 0.02). Desorption did not greatly depend on the concentration at which it was determined and showed higher hysteresis for more sorptive soils. Results of triadimefon sorption on model sorbents supported that both humic acid and montmorillonite-type clay constituents contribute to triadimefon retention by soil colloids.     

Fate of isoxaflutole in soil under controlled conditions

Isoxaflutole (IFT, 5-cyclopropyl-1,2-oxazol-4yl-alpha,alpha,alpha-trifluoro-2-mesyl-p-tolyl ketone) is a new pre-emergence proherbicide used in maize and sugarcane. Its two main derivatives are a diketonitrile derivative, 2-cyano-3-cyclopropyl-1-(2-methanesulfonyl-4-trifluoromethylphenyl)propane-1,3-dione, called DKN, and a benzoic acid derivative, 2-methanesulfonyl-4-trifluoromethylbenzoic acid, called BA. Few data are available of the factors influencing the degradation of IFT in soil, and the purpose of the present work was to determine the relative importance of, and factors affecting, the degradation of IFT in soil. Experiments were conducted on five soils with distinct physicochemical characteristics, at different temperatures and moisture contents in biotic and abiotic conditions. The isomerization of IFT to DKN is rapid, increasing with higher moisture contents and higher temperatures. It depends strongly on pH and is governed by chemical processes. The degradation of DKN to BA appeared to be essentially due to the biological activity of the soil.     

Improved HPLC-MS/MS method for determination of isoxaflutole (balance) and its metabolites in soils and forage plants

A robust multi-residue procedure is needed for the analysis of the pro-herbicide isoxaflutole and its degradates in soil and plant materials at environmentally relevant (<1 microg kg-1) levels. An analytical method using turbo-spray and heat-nebulizer high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was developed for the analysis of isoxaflutole (IXF) and its two metabolites, diketonitrile (DKN) and the benzoic acid metabolite (BA), at sub-microgram per kilogram levels in soil and plant samples. The average recoveries of the three compounds in spiked soil and plant samples ranged from 84 to 110% and 94 to 105%, respectively. The limits of quantification were validated at 0.06 microg kg-1 for soil and 0.3 microg kg-1 for plant samples. The limits of detection (LOD) for soil analysis were 0.01, 0.002, and 0.01 microg kg-1 for IXF, DKN, and BA, respectively. Corresponding LOD for the plant analysis method were 0.05, 0.01, and 0.05 microg kg-1. The developed method was validated using forage grass and soil samples collected from a field lysimeter study in which IXF was applied to each of four forage treatments. Forage plants and soils were sampled for analyses 25 days after IXF application to the soil. In soils, IXF was not detected in any treatment, and DKN was the predominant metabolite found. In forage plants, the concentrations of DKN and BA were 10-100-fold higher than that in soil samples, but IXF was not detected in any forage plants. The much higher proportion of BA to DKN in plant tissues (23-53%), as compared to soils (0-5%), suggested that these forages were capable of detoxifying DKN. The developed methods provided LODs at sub-microgram per kilogram levels to determine the fate of IXF and its metabolites in soils and forage plants, and they also represent considerable improvements in extraction recovery rates and detection sensitivity as compared to previous analytical methods for these compounds.     

Role of Different Soil Fractions in Copper Sorption by Soils

Abstract

To evaluate contributions of organic matter, oxides, and clay fraction to copper (Cu) adsorption in six characterized soils, adsorption isotherms and distribution coefficients were obtained by a batch experimental method. Copper adsorption isotherms from untreated soil, organic matter removed from samples, and organic‐matter‐ and oxide‐removed samples were compared with curve patterns and correlated to Langmuir and Freundlich models. Copper sorption data on untreated soils described L or H‐curves, whereas in soils deprived of any component, their curves were S‐type. Distribution coefficients allowed knowing Cu adsorption capacity of untreated soil and of organic matter, oxides, and clay fraction. Soil organic matter is the main component that affects Cu adsorption as long as soil pH is near neutrality. At acid pH, oxides are the main component that affects Cu adsorption, although to a much smaller extent than organic matter near neutral conditions. Soil pH is the main soil factor that determines Cu adsorption.     

Differences in sorption behavior of the herbicide 4-chloro-2-methylphenoxyacetic acid on artificial soils as a function of soil pre-aging

Purpose

The sorption behavior of the herbicide 4-chloro-2-methylphenoxyacetic acid (MCPA) to three different artificial soil mixtures was investigated. Artificial soils serve as model systems for improving understanding of sorption phenomena.

Materials and methods

The soils consisted of quartz, ferrihydrite, illite, montmorillonite, and charcoal. In a previous study, several selected mixtures had been inoculated with organic matter, and microbial aging (incubation) had been performed for different periods of time (3, 12, and 18?months) before conducting the sorption experiments. The effect of this pre-incubation time on the sorption behavior was determined. Interaction of MCPA with soil surfaces was monitored by aqueous phase sorption experiments, using high-performance liquid chromatography/ultraviolet and in selected cases Fourier-transformed infrared spectroscopy.

Results and discussion

The sorption behavior showed large differences between differently aged soils; Freundlich and linear sorption model fits (with sorption constants K _f , 1/n exponents, and K _d values, respectively) were given for pH?=?3 and the unbuffered pH of ??7. The largest extent of sorption from diluted solutions was found on the surfaces with a pre-incubation time of 3?months. Sorption increased at acidic pH values.

Conclusions

Regarding the influence of aging of artificial soils, the following conclusions were drawn: young artificial soils exhibit stronger sorption at lower concentrations, with a larger K _f value than aged soils. A correlation with organic carbon content was not confirmed. Thus, the sorption characteristics of the soils are more influenced by the aging of the organic carbon than by the organic carbon content itself.     

Azimsulfuron sorption--desorption on soil

The sorption and desorption of the herbicide azimsulfuron, N-[[(4-dimethoxypyrimidin-2-yl)amino]carbonyl]1-methyl-4-(2-methyl-2H-tetrazole-5-yl)1H-pyrazole-5-sulfonamide, were studied using five soils. Sorption isotherms conformed to the Freundlich equation. It was found that pH is the main factor influencing the sorption and that the sorption on soils was negatively correlated with pH. The highest level of sorption was measured on soils with low pH and high organic carbon content. Moreover, inorganic soil colloids, for example, smectite clay minerals and iron oxides, contributed to the sorption of azimsulfuron. Desorption was hysteretic on soils with high organic and inorganic colloid contents.     

Ibuprofen Sorption to Coastal Plain Soils

Ibuprofen is commonly detected in onsite wastewater systems. Such onsite systems are abundant in coastal plain areas, globally. Coastal plain soils have unique mineralogy. Rapid subsurface transport may occur in coastal plain soils due to their characteristic permeable soils and seasonally high water tables. Laboratory batch sorption studies were conducted on Norfolk, Goldsboro, and Lynchburg, three archetypical coastal plain soils, with varying physicochemical properties, to evaluate ibuprofen sorption. Sorption distribution coefficients (K_D values) across all three soils ranged from 0.63 to 1.26 L kg^?1. Sorption of ibuprofen to Norfolk and Goldsboro soils was able to be modeled using a Freundlich isotherm; however, the Lynchburg soil, was not, likely due to soil heterogeneity. In general, sorption of ibuprofen was influenced by soil organic carbon content.     

菲在土壤/沉积物上的吸附-解吸过程及滞后现象的研究

实验研究了菲在土壤 /沉积物上的吸附 解吸过程。CHL土壤和HFH沉积物中有机质的固相13 CCPMASNMR谱图很相似 ,表明样品中有机质的组成差异不大 ;菲在土壤 /沉积物上的吸附过程表现出明显的非线性 ;线性模型不适合拟合菲的吸附等温线 ,Freundlich模型和双区位反应模型 (DRDM)较好地拟合了菲的吸附等温线 ,其中DRDM模型还清楚地反映菲在低浓度和高浓度下不同的吸附方式 ;另外 ,研究表明菲在土壤 /沉积物上的解吸过程中存在明显的滞后现象 ,这可能和土壤 /沉积物有机质的异质性和土壤胶团微小孔隙的存在有关。     

Behavior of phenol and aniline on selected sorbents and energy-related solid wastes

The sorption and desorption of phenol and aniline on selected soils and soil components and on some energy-related solid wastes were investigated. Isotherms were generally nonlinear and were described usually by the Freundlich equation. Most partition coefficients were low, and no significant correlation was shown with organic C content, pH, cation exchange capacity, or particle-size of the sorbent. It appears that sorption of small polar aromatic compounds, such as phenol and aniline, cannot be defined by a single sorbent characteristic, but is affected by both the organic and mineral components of the sorbents. Hysteresis was observed in most sorption-desorption experiments; a fraction of the sorbate was irreversibly held by the sorbent.     

铬在土壤中的吸附解吸研究进展

对铬在土壤中的吸附解吸研究进行了综述,土壤中铬的吸附解吸机理包括非专性吸附(离子交换吸附)、专性吸附以及物理表面吸附,分别对pH、氧化还原电位、土壤组分(土壤矿物和有机质)、竞争离子以及离子强度等因素对铬吸附解吸的影响作了论述。文章进一步描述了土壤中铬吸附解吸的数学模型Freundlich方程、Langmuir方程、一级动力学模型、金属-腐殖酸模型(one-sitemodel)和表面络合模型-扩散层模型(DLM)等的研究情况,并对今后的研究方向进行了探讨。     

Influence of organic matter and pH on bentazone sorption in soils

Bentazone (3-isopropyl-1H-2,1,3-benzonthiadiazain-(4)3H-one 2,2-dioxide) is a postemergence herbicide which is used extensively worldwide, especially in China. The sorption of bentazone in various types of soils and extracted humic acids was investigated using a batch equilibration technique. Significant linearity was observed in sorption isotherms in five different types of soil, with distribution coefficients (K(d)) that varied between 0.140 and 0.321 mL g(-1). The distribution coefficient was determined to be a function of organic matter and pH in the soil. A model based on distribution coefficients was developed to predict bentazone sorption in soils. The organic matter-normalized partition coefficients for the neutral and anionic forms of bentazone were 370.3 and 2.40 mL g(-1), respectively. Hence, more attention should be given to the potential leaching problem when bentazone is applied in soils containing low organic matter and high pH.     

Degradation of isoxaflutole (balance) herbicide by hypochlorite in tap water

Chlorine has been widely employed for the disinfection of drinking water. Additionally, it has the capacity to oxidize many organic compounds in water. Isoxaflutole (Balance; IXF) belongs to a new class of isoxazole herbicides. Isoxaflutole has a very short soil half-life and rapidly degrades to a stable and phytotoxic metabolite, diketonitrile (DKN). Further degradation of DKN produces a nonbiologically active benzoic acid (BA) metabolite. In experiments using high-performance liquid chromatography-UV spectroscopy (HPLC-UV) and HPLC tandem mass spectrometry (HPLC-MS/MS), DKN was found to rapidly react with hypochlorite in tap water, yielding the BA metabolite as the major end product. One milligram per liter (19 microM) of hypochlorite residue in tap water was able to completely oxidize up to 1600 microg/L (4.45 micromol/L) of DKN. In tap water, the disappearance of IXF was much more rapid than in DI water. As soon as the IXF is hydrolyzed to DKN, the DKN quickly reacts with the OCl(-) to form nonphytotoxic BA. As a result, the herbicide solutions prepared with tap water at 500 microg/L will no longer possess any herbicidal activity after 48 h of storage. However, in agronomic settings, highly concentrated tank solutions (600-800 mg/L) may be prepared with tap water since the conversion of IXF to BA would represent <5% of the herbicide; therefore, any impact on the herbicide efficacy would be negligible. Results of this study show that current chlorination disinfection protocols in municipal water systems would completely eliminate the phytotoxic form of this new herbicide, DKN, from drinking water supplies; yet, farmers can use chlorinated tap water without significant loss of efficacy.     

Modelling the effects of pH on phosphate sorption by soils

Samples of six soils were incubated at 60°C for 24 h with several levels of either calcium carbonate or hydrochloric acid. Phosphate sorption was then measured on sub-samples of the treated soils over 24 h at 25°C. In one set of measurements on all soils, 0.01 M calcium chloride was used as the background electrolyte. In another set, on two soils, 0.01 M sodium chloride was used. An interpolation method was used to give points on the three-dimensional surface relating the final pH of the suspensions to sorption of phosphate at specified solution concentrations of phosphate. The effects of pH on phosphate sorption differed between soils. For unfertilized soils, increases in pH up to about pH 5.5 decreased sorption. Further increases in pH decreased sorption further in one soil and increased it in three others. For fertilized soils, measured sorption increased with pH. When sodium chloride was used instead of calcium chloride, there was a more marked trend for sorption to decrease as pH increased. Differences between the soils were ascribed to differences in two soil properties. One was the rate at which the electrostatic potential in the plane of adsorption decreased as pH increased. Only small differences in the rate of change of potential were needed to reproduce the observed differences between soils. The electrostatic potential would decrease more quickly in solutions of a sodium salt than in solutions of a calcium salt and this explains the observed differences between these media. The other soil property that affected observed sorption was the release of phosphate from the soil. The amount released was largest at low pH. Consequently, for fertilized soils, measured sorption increased with pH.     

Sorption behavior of prochloraz in different soils.

The sorption behavior of the imidazole fungicide prochloraz [PCZ; N-propyl-N-[2-(2,4,6-trichlorophenoxy)ethyl]imidazole-1-carboxamide] was studied in batch experiments with different soils. The soil organic matter content was found to control the amount sorbed by different soils. K(d) values ranged from 56 +/- 0 to 552 +/- 10 (mean = 221 +/- 5) and K(OC) values from 7273 +/- 0 to 16250 +/- 1300 (mean = 11829 +/- 303). As calculated from a linear regression of K(d) versus %OC, K(OC) was 12900 +/- 1300. Additionally, the pH value of the soil had considerable influence on the sorption of the weakly basic PCZ (pK(a) = 3.8), giving rise to stronger sorption at lower pH. K(d) values determined on pH-modified soils confirmed the pH dependency. Sorption isotherms on two soils were recorded, initial concentrations ranging from 0.09 to 5.71 mg L(-)(1). The Freundlich isotherm was fitted to the values measured. The Freundlich exponents calculated were significantly smaller than unity, indicating nonlinear sorption. Sorption experiments with two metabolites of PCZ (PCZ-formylurea and PCZ-urea) revealed K(d) values one-fourth to one-third those for PCZ on two soils.     

Influence of Increasing Soil Copper Concentration on the Susceptibility of Phosphomonoesterase and Urease to Heat Disturbance

The sorption of chromium (Cr) species to soil has become the focus of research as it dictates the bioavailability and also the magnitude of toxicity of Cr. The sorption of two environmentally important Cr species [Cr(III) and Cr(VI)] was examined using batch sorption, and the data were fitted to Langmuir and Freundlich adsorption isotherms. The effects of soil properties such as pH, CEC, organic matter (OM), clay, water-extractable SO₄ ^2– and PO₄ ^3–, surface charge, and different iron (Fe) fractions of 12 different Australian representative soils on the sorption, and mobility of Cr(III) and Cr(VI) were examined. The amount of sorption as shown by K _f was higher for Cr(III) than Cr(VI) in all tested soils. Further, the amount of Cr(III) sorbed increased with an increase in pH, CEC, clay, and OM of soils. Conversely, the chemical properties of soil such as positive charge and Fe (crystalline) had a noticeable influence on the sorption of Cr(VI). Desorption of Cr(VI) occurred rapidly and was greater than desorption of Cr(III) in soils. The mobility of Cr species as estimated by the retardation factor was higher for Cr(VI) than for Cr(III) in all tested soils. These results concurred with the results from leaching experiments which showed higher leaching of Cr(VI) than Cr(III) in both acidic and alkaline soils indicating the higher mobility of Cr(VI) in a wide range of soils. This study demonstrated that Cr(VI) is more mobile and will be bioavailable in soils regardless of soil properties and if not remediated may eventually pose a severe threat to biota.     

Sorption and desorption behaviour of acetochlor in surface, subsurface and size-fractionated soil

Pesticides leaching through a soil profile will be exposed to changing environmental sorption and desorption conditions as different horizons with distinct physical and chemical properties are encountered. Soil cores were taken from a clay soil profile and samples taken from 0.0 to 0.3 m (surface), 1.0–1.3 m (mid) and 2.7–3.0 m (deep) and treated with the chloroacetanilide herbicide, acetochlor. Freundlich isotherms revealed that sorption and desorption behaviour varied with each depth sampled. As soil depth increased, the extent and strength of sorption decreased, indicating that the potential for leaching was increased in the subsoils compared with the surface soil. Hysteresis was evident at each of the three depths sampled, although no significant correlations between soil properties and the hysteresis coefficients were evident. Desorption studies using soil fractions with diameters of > 2000, 250–2000, 53–250, 20–53, 2–20, 0–2 and 0–1 µm separated from each of the three soil depths showed that differential desorption kinetics occurred and that the retention of acetochlor significantly correlated (R² = 0.998) with organic matter content. A greater understanding of the influence of soil components on the overall sorption and desorption potential of surface and subsurface soils is required to allow accurate prediction of acetochlor retention in the soil. In addition, it is likely that the proportion of each size fraction in a soil horizon would influence acetochlor bioavailability and movement to groundwater.     

干旱区绿洲灌漠土对铜的吸附解吸特性研究

土壤对重金属的吸附解吸是影响土壤系统中重金属的移动性和归宿的主要过程.本文使用序批实验方法、单步提取方法、连续提取方法等研究了干旱区绿洲灌漠土Cu的吸附解吸特性.结果表明,灌漠土对Cu的吸附等温线可很好地用Freundlich等温方程拟合,灌漠土的Cu吸附可能受土壤理化综合因素影响,而不仅是某个土壤理化指标所控制;二次...