不同桉木化学机械法制浆性能的研究

研究了尾巨桉、巨尾桉、尾叶桉、蓝桉及小叶桉这5种桉木的材性特征及其预处理-碱性过氧化氢化学机械浆(P-RC APMP)制浆性能。结果表明:5种桉木的综纤维素质量分数在77.96%~81.36%之间,小叶桉最高,巨尾桉最低;木质素质量分数在23.18%~26.62%之间,尾叶桉的最高,巨尾桉最低;纤维平均长度在755~785μm之间,差异较小。采用P-RC APMP制浆方法,在H2O2用量5%,Na OH用量4.5%浸渍条件下,小叶桉的制浆得率最高,达86.7%,巨尾桉最低,仅为84.2%;在相同加拿大游离度(300 m L CSF)下,蓝桉浆的强度性能和光学性能最优,纸浆的抗张强度和白度分别达30.13(N·m)/g和82.5%(ISO),且所需磨浆电耗最低,仅1 188 k Wh/t,巨尾桉浆的强度性能和光学性能最差,纸浆的抗张强度和白度分别为16.9(N·m)/g和73.8%(ISO),且所需磨浆电耗最高,约为1 370 k Wh/t。     

DMD的活化预处理及其全无氯漂序的研究

研究了桉木硫酸盐浆对氧脱木质素段和过氧化氢漂段的活化作用以及ＤＭＤ用量对氧段和过氧化氢段浆性能的影响,使经ＭＯＱＭＰ多段漂白的纸浆最终白度达８０％以上,纸浆粘度满足要求,可以实现桉木硫酸盐浆的全无氯漂白。     

尾巨桉与马占相思木材P-RC APMP工艺制浆性能比较

以尾巨桉与马占相思为原料,采用P-RC APMP工艺对比研究两者的化学机械法制浆性能.研究结果表明.相同的过氧化氢用量4.0%,氢氧化钠用量3.5%条件下,两种原料制得纸浆的白度相近均可达75%以上;马占相思原料制浆得率比尾巨桉约高3%左右,物理强度性能远优于尾巨桉浆,相同的250 ml加拿大游离度下,尾巨桉纸页的抗张强度仅为20.1 N·m·g-1,而马占相思纸页的抗张强度可达到26 N·m·g-1 以上.制得抗张强度相近的纸浆,马占相思比尾巨桉所需的磨浆电耗约低20%.     

麦草化学机械制浆预处理方法研究

使用麦草原料制取漂白化学机械浆,为了后续多段漂白能够获得高白度的纸浆,研究了3种不同的化学药品用于预浸渍阶段对未漂白浆的光学和物理性能的影响,包括成浆白度、成浆强度指标、纤维筛分级分,并比较了磨浆的比能耗和废水污染负荷.研究结果表明,与碱性过氧化氢(2.0%NaOH、1.5%H2O2、0.4%DTPA)处理(P工艺)磨浆相比亚硫酸钠(2.0%Na2SO3、2.0%Na2CO3、0.4%DTPA)预处理(S工艺)磨浆比能耗降低了33%,果胶酶(10IU/g以绝干浆计)/碱性过氧化氢(2.0%NaOH、1.5%H2O2、0.4%DTPA)预处理(Pe/P工艺)也可以降低磨浆比能耗10%,P工艺预处理与S工艺预处理均能提高成浆白度,Pe/P工艺预处理成浆呈现暗红色;P工艺预处理成浆物理强度高于其他两种浆;S工艺预处理磨浆段废水化学耗氧量(COD)发生量较高,达到84.09kg/t(以绝干浆计).     

桉树制浆综述

本文介绍了(1)用桉木生产漂白化学浆,包括硫酸盐法和碱一蒽醌法制浆;(2)用按木生产漂白半化学浆,主要是中性亚硫酸盐半化学高得率浆;(3)用桉木生产漂白化学机械浆,包括冷碱法和亚硫酸盐法制浆;(4)用桉木生产漂白化学热磨机械浆。     

微波预处理对桉木化机浆性能的影响

通过微波、水浴两种加热方式下浸渍木片吸液量的比较,探究了微波对桉木渗透性的影响,结果显示:在其它浸渍条件(NaOH质量分数4%,木片质量分数20%)相同的情况下,木片浸渍时,经微波加热后其吸液量较水浴加热显著提高,微波处理5 min即可达到水浴处理45 min的吸液量,大大提高了浸渍效率。将微波用于化学机械法制浆的预浸渍阶段,经微波处理所得纸浆二段漂白白度最高可达68.9%(ISO),较汽蒸保温提高3～6个百分点;在加拿大游离度为305 mL时,微波处理浆的抗张指数可达19 N·m/g,撕裂指数可达2.15 mN·m^2/g,耐破指数达0.8 kPa·m^2/g,分别比汽蒸处理样高3 N·m/g、0.2 mN·m^2/g和0.1 kPa·m^2/g。     

酶处理对混合杨木P-RC APMP浆打浆性能的影响

探讨了纤维素酶、木聚糖酶处理对混合杨木温和预处理和盘磨化学处理的碱性过氧化氢机械浆(P-RC APMP)的打浆性能和打浆能耗的影响。结果表明:与未经过酶处理浆相比,纤维素酶和木聚糖酶处理可明显改善纸浆的打浆性能和降低打浆能耗,纸浆打浆度提高1.0～6.5°SR,或在相同打浆度下打浆能耗降低10%～25%。纤维素酶处理浆裂断长提高18%,撕裂指数提高14%,耐破指数提高16%,耐折度提高100%。木聚糖酶处理纸浆白度提高1.7度(ISO),纸浆物理强度略有上升。纤维素酶在改善纸浆打浆性能、降低打浆能耗和提高物理强度方面好于木聚糖酶,木聚糖酶在改善纸浆光学性能方面优于纤维素酶。酶处理可以使纸浆纤维结构变得疏松柔软,从而增强纤维间的交织能力。     

尾巨桉与马占相思P-RC APMP工艺制浆性能比较

以尾巨桉和马占相思为原料,采用经化学预处理的碱性过氧化氢机械浆(P-RCAPMP)制浆工艺对比研究两者的制浆性能.研究结果表明,相同的H2O2用量(4.0%)和NaOH用量(3.5%)条件下,2种原料制得纸浆的白度相近,均可达75%左右;马占相思原料制浆得率比尾巨桉约高3%左右,物理强度性能远优于尾巨桉浆,相同的250mL加拿大标准游离度(CSF)下,尾巨桉纸页的抗张强度仅为20.1N·m/g,而马占相思纸页的抗张强度可达到26.0N·m/g以上.制得相近CSF的纸浆,马占相思制浆所需的磨浆电耗比尾巨桉略高;2种原料制浆废水的化学耗氧量(COD)和生物耗氧量(BOD)发生量相近,而尾巨桉的制浆废水中固体悬浮物(SS)及总固形物(TS)含量远高于马占相思废水.     

纤维素酶预处理对杨木APMP浆配抄性能的影响

为了改善杨木高得率浆的配抄性能,扩大其应用范围,研究探讨了纤维素酶预处理对杨木碱性过氧化氢机械浆(APMP浆)配抄性能的影响。结果表明,与未经过酶预处理的杨木APMP浆相比,酶处理后APMP浆打浆能耗最大可降低19%,纤维吸水润胀程度增加,保水值增加12.6%;与不同比例针叶木漂白硫酸盐浆(BKP浆)配抄后,纸张的裂断长、耐破指数和撕裂指数均有所提高,最大可分别提高6.1%,44.6%和30.3%,纸张的松厚度、白度和不透明度稍有降低。纤维质量分析仪(FQA)、扫描电镜(SEM)和X射线衍射(XRD)分析结果显示,酶处理后纤维平均长度增加7.0个百分点,细小纤维组分减少10.0%,纤维卷曲指数降低22.4%,结晶度提高0.7%。可见,纤维素酶预处理可以改善杨木APMP浆的配抄性能,提高纸浆纤维质量,所配抄的纸张的物理强度性能指标有显著提高。     

三种速生阔叶木的PRC-APMP制浆性能比较

对比了杨木、桉木和相思木3种速生阔叶木的材性和PRC-APMP制浆性能,研究结果表明:杨木比桉木和相思木具有更高的聚戊糖和1%NaOH抽出物含量;桉木综纤维素含量略低于杨木和相思木,同时木质素含量最高;桉木材密度最大,相思木次之,杨木较低。采用PRC-APMP制浆方法,在NaOH总用量5.5%,H_2O_2用量5.0%浸渍漂白条件下,相思木制浆得率最高(83.8%),桉木次之(82.4%),杨木最低(81.3%)。桉木成浆白度最高78.2%(ISO,下同),杨木次之75.3%,相思木浆白度最低70.7%。在同等浆料打浆度条件下,相思木成浆抗张强度大于杨木和桉木,同时消耗磨浆电耗也最高;杨木成浆的纤维长度较大,浆料撕裂强度大于相思木和桉木;桉木成浆的抗张和撕裂强度均最低,但浆料具有高松厚度特性。     

Explosion pulping of eucalyptus: a comparison with CTMP and CMP

Summary Explosion pulping results in strong pulp with breaking length at 100 ml CSF (Canadian standard freeness) higher than 6.5 kg and burst index approaching 4 KPa m²/g. The real advantage of eucalyptus explosion pulp over conventional CMP (chemical-mechanical pulp) and CTMP (chemical-thermo-mechanical pulp) is observed when the impregnation solution contains less than 2% NaOH along with 8% Na₂SO₃, and when the liquor/chips ratio equals 3. The strength of eucalyptus explosion pulp obtained by using a pretreatment solution consisting of 8% Na₂SO₃ and 1% NaOH is comparable with that of eucalyptus kraft pulp. The concentration of NaOH present in the pretreatment solution has a very important effect on the specific refining energy of eucalyptus explosion pulp as well as of CMP and CTMP. The explosion pulp obtained from eucalyptus pretreated with a solution containing an appropriate quantity of caustic along with Na₂SO₃ not only requires a minimum specific refining energy but also provides the highest strength values in comparison to that of CMP and CTMP.     

NEW PULPING METHOD FOR LINERBOARD

Traditionallykraftwasusedaslinerforlinerboard.Thekrafpulpingyieldwaslow,andairpollutionhigh.SomeresearcheshaveshownthattheyieldofAS-AQpulpwasmuchhigherthanthatofkraft,andthestrengthwasequaltothatofkraft,exceptforasome-whatlowertearstrength.Thewashingprofi-clencyofAS-AQpulpwashigherandairpol-lutionwasmuchlowerthanthoseofkraft.SoAS-AQpulpwasthoughtasapromisingre-placementofkraftforlinerboard.lntheresearchPinuskoraiensiSandLarljgmehniwereusedasrawmaterials,withtheL,(3')experimentaldesignan…     

Investigation on physical and mechanical properties of pulp–plastic composites from bagasse

High-density polyethylene (HDPE), bagasse fibers treated by four pulping processes (AS-AQ (alkaline sulfite anthraquinone), SODA-AQ (soda anthraquinone), MEA (monoethanolamine) and chemical–mechanical pulping (CMP)), three levels of nano-SiO₂ (0, 2, and 5?wt%), and maleic anhydride polyethylene as coupling agent were used to produce pulp–plastic composites (PPCs) by injection molding. The physical and mechanical properties of corresponding composites were evaluated according to ASTM standards. The results showed that compared to untreated bagasse/HDPE composite, the addition of bagasse pulp fibers increased significantly the mechanical properties such as tensile strength and modulus, flexural strength and modulus, and hardness. The chemical pulps-reinforced composites showed better mechanical strengths than that of CMP-reinforced composites, but in some properties, CMP pulp composites have comparable results to the chemical pulp-reinforced composites. Natural fibers (untreated and treated) increased water absorption and thickness swelling of composites compared to pure HDPE. The addition of nano-SiO₂ particles showed both increasing and decreasing trends on physical and mechanical properties ofPPCs.     

桉树CTMP法制浆性能的研究

应用正交试验设计方法分析预浸时间、预浸温度、NaOH用量、Na2SO3用量对尾巨桉CTMP制浆性能的影响并选取最优方案,在此基础上,对4年生和6年生尾巨桉分别进行制浆抄纸,并对纸张物理性能进行测定。研究表明,适当的预浸时间、预浸温度、NaOH用量、Na2SO3用量可制得质量较好的CTMP。     

麦草低温氧碱蒸煮黑液降黏技术

麦草经碱法蒸煮后,所得浆料不经洗涤,直接通入氧气进行处理。以黑液黏度,浆料卡伯值为考核指标,设置4因素3水平正交试验,对试验结果作极差分析发现,在用碱量0～2%、氧压0.2～0.6 MPa、温度70～100℃和时间30～90 min内得到较适宜的工艺条件为:用碱量1%,氧压0.6 MPa,温度85℃,时间60 min。氧碱蒸煮结果为:黑液黏度3.4 mPa.s,浆料卡伯值17.9。与第一段碱法蒸煮相比,黑液黏度降低33.3%,浆料卡伯值降低11.8%。     

Industrial utilization of tobacco stalks II: preparation and characterization of tobacco pulp by steam explosion pulping

Our previous paper showed tobacco stalks to posses the characteristics of a raw material for pulp and paper application. It contains the major biomass constituents and cell components common to wood species. In this study, preparation and characterization of tobacco stalk pulp by steam explosion (SE) pulping at two chemical pretreatments were attempted. Chemical pretreatment prior to SE pulping improved the brightness, yield, and strength properties of the resulting tobacco SE pulps in the order: 6% Na₂SO₃ + 1% NaOH > 6% Na₂SO₃ > control (untreated). The 6% Na₂SO₃ + 1% NaOH-impregnated tobacco stalks produced SE pulps of good fiber length distribution and considerable properties that compare well with pulps from other raw materials obtained from previous studies, and the nonimpregnated ones showed strength properties superior to those of their poplar counterpart. Prior to bleaching, pretreating the tobacco stalk SE pulps with two stages, 2% NaOH at 90°C, improved the initial pulp brightness by about 5 points. Two-stage 6% H₂O₂ bleaching gave a comparable effect with hypochlorite bleaching for both tobacco and poplar, giving a 29–34 brightness point increase for tobacco SE pulp and 61 for the poplar samples. The differences in the bleaching responses for untreated tobacco and poplar SE pulps were attributed to the differences in their lignin structure, as shown in the total yield of their respective nitrobenzene oxidation products and FT-IR spectra. Tobacco SE pulps contain more of the guaiacyl-type lignin and poplar the syringyl-type lignin.This paper was presented in part during the 1998 CORESTA (Cooperation Centre for Scientific Research Relative to Tobacco) Congress, Brighton, UK, October 1998     

狼毒根手工成浆与烧碱法成浆的比较

用烧碱法替代传统手工方法制取狼毒根纸浆的比较试验结果证明,二者之间还是存在很大的差异,常规的化学法成浆尚达不到传统的手工法的除杂、润胀和细纤维化的程度,因此性能也达不到手工成浆的水平,不能简单的替代.     

中国引种澳大利亚相思树种制硫酸盐浆适应性研究

无论是从林业角度还是在制浆性能方面，不同种源间存在明显差异。本文研究了我国亚热带工区引种澳大利亚相思树的基本密度纸浆产率、制硫酸盐浆和漂白性能，比较了不同种源间的差异。研究结果表明，在有效碱用量为１２．５％－１５．５％时纸浆得率达５１．２％－５３．６％，经ＣＥＨＤ四段漂白后，所得纸浆性能可以满足配抄印刷和包装类用纸要求。