Effect of matrix viscosity on clay dispersion in preparation of polymer/organoclay nanocomposites

The viscosity effect of matrix polymer on melt exfoliation behavior of an organoclay in poly(ε-caprolactone) (PCL) was investigated. The viscosity of matrix polymer was controlled by changing the molecular weight of poly(ε-caprolactone), the processing temperature, and the rotor speed of a mini-molder. Applied shear stress facilitates the diffusion of polymer chains into the gallery of silicate layers by breaking silicate agglomerates down into smaller primary particles. When the viscosity of PCL is lower, silicate agglomerates are not perfectly broken into smaller primary particles. At higher viscosity, all of silicate agglomerates are broken down into primary particles, and finally into smaller nano-scale building blocks. It was also found that the degree of exfoliation of silicate layers is dependent upon not only the viscosity of matrix but thermodynamic variables.     

Characteristics of sounds generated from vapor permeable water repellent fabrics by low-speed frictions

To investigate the sound properties by low-speed frictions (0.2 m/s and 0.5 m/s) which occur when two fabrics are rubbed by wearer’s slow movement, six specimens are selected by cluster analysis among seventy-one vapor permeable water repellent fabrics for outdoor sportswear. Their sound spectra are obtained from the FFT analysis. Physical sound properties (LPT, ΔL, Δf) and Zwicker’s psychoacoustic parameters-loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z)-are calculated from the sound spectra. Mechanical properties of the fabrics are measured with the KES-FB system. The amplitudes of the sound spectra of all the specimens at 0.5 m/s are higher than those at 0.2 m/s throughout the entire range of frequencies. As the frictional speed changed from 0.2 m/s to 0.5 m/s, the LPT increases about 16 dB, and the loudness(Z) and fluctuation strength(Z) increase about 3 times and 2 times, respectively. The SMD and Weight at the two low frictional speeds are the important factors which affect the sound properties of vapor permeable water repellent fabrics.     

The effects of blend composition and blending time on the ester interchange reaction and tensile properties of PLA/LPCL/HPCL blends

PLA/LPCL/HPCL blends composed of poly(lactic acid) (PLA), low molecular weight poly(ε-caprolactone) (LPCL), and high molecular weight poly(ε-caprolactone) (HPCL) were prepared by melt blending for bioabsorbable filament sutures. The effects of blend composition and blending time on the ester interchange reaction by alcoholysis in the PLA/LPCL/HPCL blends were studied. Their thermal properties and the miscibility due to the ester interchange reaction were investigated by¹H-NMR, DSC, X-ray, and UTM analyses. The hydroxyl group contents of LPCL in the blends decreased by the ester interchange reaction due to alcoholysis. Thus, the copolymer was formed by the ester interchange reaction at 220 °C for 30–60 minutes. The thermal properties of PLA/LPCL/HPCL blends such as melting temperature and heat of fusion decreased with increasing ester interchange reaction levels. However, the miscibility among the three polymers was improved greatly by ester interchange reaction. Tensile strength and modulus of PLA/LPCL/HPCL blend fibers increased with increasing HPCL content, while the elongation at break of the blend fibers increased with increasing LPCL content.     

Properties of crosslinked waterborne polyurethane adhesives with modified melamine: Effect of curing time, temperature, and HMMM content

A series of crosslinked waterborne polyurethane (WBPU) adhesives were prepared by prepolymer synthesis. Modified melamine, hexamethoxymethyl melamine (HMMM) was used as the crosslinking agent. It was elucidated by FTIR and ¹H-NMR spectroscopy that the crosslinking reaction occurred between the polyurethane carboxyl acid salt groups and the HMMM methoxy groups. The hydrophobicity of the WBPU films increased after HMMM crosslinking. As the HMMM content was increased (increasing mole ratio of HMMM/dimethylol propionic acid (DMPA)), the water uptake (%) of the film decreased, and the water contact angle increased. The thermal stability, tensile strength, and initial modulus increased with increasing HMMM content up to an optimum value (mole ratio of HMMM/DMPA=0.5) at which point the maximum thermal stability, tensile strength, and initial modulus were recorded. The adhesive strength was found to be dependent on HMMM content, curing time, and temperature. The adhesive strength of crosslinked WBPU in the case of optimum HMMM content (8.46 wt%) was only slightly affected after immersing adhesive bonded nylon fabrics in water (for up to 2 days).     

Psychoacoustic characteristics of fibers

In order to investigate psychoacoustic characteristics of fibers, and to compare them with sound physical parameters, each sound of 25 different fabrics consisted of a single fiber such as wool, cotton, silk, polyester, and nylon was recorded. Sounds of specimens were transformed into critical band diagram and psychoacoustic characteristics including loudness and sharpness for each sound were calculated based on Zwicker’s models. Physical parameters such as the level pressure of total sound (LPT), level ranges (ΔL), frequency differences (Δf), AR coefficients (ARC, ARF, ARE) were obtained in fast fourier transform (FFT) spectrum. Nylon taffeta showed higher values for loudness than 2.5 sone corresponding to human low conversation, while most silk fibers generated less louder showing lower values for loudness than 1.0 sone. Wool fibers had higher loudness mean value than that of cotton, while the two fibers didn’t differ in LPT. Loudness showed high positive correlation coefficients with both LPT and ARC. Sharpness values were higher for wool fiber group than other fibers. Sharpness was not concerned with loudness, LPT, and ARC, but the fabrics with higher values for sharpness tended to show higherΔL.     

Dyeing properties and colour fastness of cotton and silk fabrics dyed with<Emphasis Type="Italic">Cassia tora L.</Emphasis> extract

A natural colorant was extracted fromCassia tora L. using buffer solutions (pH: 2–11) as extractants. The dyeing solution (Cassia tora L. extract) extracted using pH 9 buffer solution was found to give the highest K/S values of dyed fabrics. Cotton and silk fabrics were dyed withCassia tora L. extract at 60°C for 60 min with pre-treatment of various metal salts as mordants. It was found thatCassia tora L. extract was polygenetic dyestuffs and its major components were anthraquinones. Studies have been made on the effects of the kind of mordant on dyeing properties and colour fastnesses of cotton and silk fabrics. The K/S of cotton fabrics increased in the order of the dyeing using FeSO₄>CuSO₄>ZnSO₄>MnSO₄≅Al₂(SO₄)₃>NiSO₄>none, however, the K/S of silk fabrics increased in the order of the dyeing using FeSO₄>CuSO₄>ZnSO₄≅Al₂(SO₄)₃>MnSO₄≅NiSO₄>none. It was found that the K/S values of dyed fabrics were largely affected by the colour difference (ΔE) between mordanted fabric and control fabric. However, they were not depended on the content of mordanted metal ion of the fabrics. Mordants FeSO₄ and CuSO₄ for cotton fabric, FeSO₄, CuSO₄, and Al₂(SO₄)₃ for silk fabric were found to give good light fastness (rating 4).     

Dyeing, fastness, and deodorizing properties of cotton, silk, and wool fabrics dyed with gardenia, coffee sludge, Cassia tora. L., and pomegranate extracts

Four kinds of natural dying solutions (natural colorant extracts) were obtained by extraction from gardenia, coffee sludge, Cassia tora. L., and pomegranate using water at 90°C for 90 min with a liquor ratio (solid natural colorant material/solvent water, weight ratio) of 1/10. The dyeing, colour fastness, and deodorizing properties of cotton, silk, and wool fabrics dyed with natural colorant extracts were compared. It was found that these properties were significantly dependent on the concentration of extracts, the structure of colorant, and the kind of fabrics. The order of colour strength (K/S) is Cassia tora. L., pomegranate, coffee sludge, and gardenia. Colour fastness (light, water, and perspiration fastness) was in the range of 2nd–5th grades. The deodorizing performance of fabrics dyed with various natural colorant extracts was in the range of 50–99 %. The deodorizing performance increased in the order of gardenia < Cassia tora. L. < coffee sludge < pomegranate. Especially, the deodorizing performance of all fabrics dyed with pomegranate was found to be highest at 99 %.     

Properties of waterborne polyurethane (WBPU) coatings: Effect of alkyl chain length of tertiary amines of carboxylic acid salt groups

Waterborne polyurethane (WBPU) dispersions were prepared via a pre-polymer process using 4,4-dicyclohexylmethane diisocyanate (H₁₂MDI), poly(tetramethyleneoxideglycol) (PTMG), 2,2-dimethylol propionic acid (DMPA), ethylene diamine (EDA), and tertiary amines (TAs) with varying amounts of DMPA and TAs. Three TAs with different alkyl chain lengths were used to neutralize the DMPA carboxylic group: N,N-dimethylbutylamine (DMBA, C4), N,N-dimethylhexylamine (DMHA, C6), and N,N-dimethyloctylamine (DMOA, C8). The structures of the synthesized WBPUs were determined via FT-IR and ¹H NMR spectroscopic techniques. The effects of DMPA and TA content and the TA alkyl chain length on stability of dispersions and properties such as water swelling (%), glass transition temperature (T _g ), tensile strength, binding energy and adhesive strength were investigated. The initial adhesive strength of the intact coatings increased with increasing DMPA and TA content and increasing alkyl chain length of TA. However, after immersion of the coatings in water, the adhesive strength decreased. The maximum adhesive strength under water was observed at a DMPA content of 20.20 mol% with 5.30 wt% DMOA, which has the longest alkyl chain.     

Critical water content and water stress coefficient of soybean (Glycine max [L.] Merr.) under deficit irrigation

The objective of this research was to investigate the critical water content (θ _c) and water stress coefficient (K _s) of soybean plant under deficit irrigation. This research was conducted in a plastic house at the University of Lampung, Sumatra in Indonesia from June to September 2000. The water deficit levels were 0–20%, 20–40%, 40–60%, 60–80%, and 80–100% of available water (AW) deficit, arranged in Randomized Completely Block (RCB) design with four replications. The results showed that the soybean plant started to experience stress from week IV within 40–60% of AW deficit. The fraction of total available water (TAW) that the crop can extract from the root zone without suffering water stress (p) was 0.5 and θ_c was 0.305 m³ m⁻³. The values of K _s at p=0.5 were 0.78, 0.86, 0.78, and 0.71 from week IV to week VII, respectively. The optimum yield of soybean plant with the highest yield efficiency was reached at 40–60% of AW deficit with an average K _s value of 0.78; this level of deficit irrigation could conserve about 10% of the irrigation. The optimum yield of soybean plant was 7.9 g/pot and crop water requirement was 372 mm.     

Effect of chemical structure on the properties of UV-cured polyurethane acrylates films

The effect of compositions of isophorone diisocyanate (IPDI)/4,4′-diphenylmethane diisocyanate (MDI) and polypropylene oxide diol (PPG,M _w : 3000)/1,4-butane diol (BD) on the properties of UV-cured polyurethane acrylate films based on 2-hydroxyethyl acrylate (HEA) was examined. UV-curable polyurethane acrylates were formulated from the prepolymer, trimethylol propane triacrylate (TMPTA) as a reactive diluent, and 1-hydroxycyclohexyl ketone (Irgacure 184) as a photoinitiator. Dynamic mechanical thermal properties and elastic properties of UV-cured polyurethane acrylates was found to depend on the chemical composition of IPDI/MDI and PPG/BD. As the BD content increased, the tensile storage modulus of all series samples increased significantly. The storage modulus increased in the order of samples A (IPDI based samples)>samples B (IPDI/MDI (7/3 molar ratio) based samples)>samples C (IPDI/MDI (5/5 molar ratio) based samples at the same composition. Two distinct loss modulus peaks for all samples are observed owing to the soft segment glass transition temperature (T _gs ) and hard segment glass transition temperature (T _gh ). The difference betweenT _gs andT _gh (ΔT _g ) increases in the order of A>B>C at the same composition. In cycle test, the initial onset strain (%) was found to decrease with increasing BD content in PPG/BD and with increasing MDI content in IPDI/MDI.     

Effect of collector temperature and conductivity on the chain conformation of nylon 6 electrospun nanofibers

Electrospinning is a versatile process used to prepare micro- and nano- sized fibers from various polymer solution. Here, we dealt with the variation in the morphology of nylon 6 electrospun nanofibers and their polymorphism depending on the type and physical state of the collectors. SEM study showed that the fiber diameter was increased from 80 to 103 nm while it was collected in water bath. Similarly the fiber diameter and bonding was increased 103 to 115 nm with the temperature whereas it was linearly decreased 103 to 90 nm with the conductivity of the water bath. Spectroscopic analysis (FT-Raman, FT-IR) showed that the polymorphism of nylon 6 depended on the types of collector (aluminum sheet and water bath). Nylon 6 electrospun nanofibers display theγ-phase while collected in aluminum sheet andα-phase while collection in water bath. The extent of transformation fromγ- toα-phase was linearly increased with temperature and conductivity of the water bath.     

Evaluation of bamboo charcoal/stainless steel/TPU composite woven fabrics

Composite woven fabric satisfies what people require. Bamboo charcoal (BC) has been identified as a multifunctional material that has far-infrared ray, anions, deodorization and etc. BC fibers and yarns were made of bamboo charcoal powders and have further become a pervasive materials used in textile industry. In this study, cotton yarns, stainless steel/cotton (SS/C) complex yarn, bamboo charcoal/cotton (BC/C) complex yarns were woven into the plain, twill and Dobby composite woven fabrics. The warp yarn was composed of cotton yarns, and the weft yarn was made up of BC/C and SS/C complex yarns with a picking ratio of 1:1 and 3:1. Thermoplastic polyurethanes (TPU) film was then attached to the composite woven fabrics, forming the BC/SS/TPU composite woven fabrics. Tests of electromagnetic shielding effectiveness (EMSE), far-infrared emissivity, anions, water resistance, and water vapor permeability measured the single-layer, two-layer and four-layer composite woven fabrics, obtaining a far-infrared emissivity of 0.95 by 39.8 counts per minute, an anion count of 149 amount/cc, an EMSE of −11.87 dB under frequency of 900 MHz, a surface resistivity of 8×10⁻⁶ Ω/square, a water resistance of −8219 mmH₂O, and water vapor permeability of 989 g/m²·h and 319 g/m²·24 h in accordance with JIS L 1099 A1 and ASTM E96 BW.     

Eco-dyeing and antimicrobial properties of chlorophyllin copper complex extracted from Sasa veitchii

Cotton fabrics were dyed with the natural chlorophyll derivates (chlorophyllin, Chlin) after treatment with and without chitosan. The water-soluble Chlin extracted from Sasa veitchii based on Japanese bamboo leaves were investigated in order to improve the textile coloration and antimicrobial activity. The antimicrobial activity of the dyed fabrics that had been pretreated with chitosan as a biomordant over a concentration range of 0∼0.7 % was tested against two common gram pathogens: Staphylococcus aureus and Klebsiella pneumoniae. The color depth as measured by the K/S value, the color difference and the colorfastness to washing and light were also evaluated. The fabrics treated with chitosan resulted in an increase in dye uptake in all cases compared with the corresponding untreated fabrics, and did not affect fastness of washing and light. The cotton fabrics dyed with mordant and CuSO₄ extracts appeared to have over 99.9 % of antimicrobial activity, while MeOH extracts showed 71.8 %.     

Simulation of salt and water movement and estimation of water productivity of rice crop irrigated with saline water

The HYDRUS-ID model was experimentally tested for water balance and salt build up in soil under rice crop irrigated with different salinity water (ECiw) of 0.4, 2, 4, 6, 8 and 10 dS m⁻¹ in micro-lysimeters filled with sandy loam soil. Differences of means between measured (M) and HYDRUS-1D predicted (P) values of bottom flux (Q _o) and leachate EC as tested by paired t test were not found significant at P = 0.05 and a close agreement between RMSE values showed the applicability of the HYDRUS-1D to simulate percolation and salt concentration in the micro-lysimeters under rice crop. Potential ET values of rice as obtained from CROPWAT matched well with model predicted and measured one at all ECiw treatments. The model predicted root water uptake varied from 66.1 to 652.7 mm and the maximum daily salt concentration in the root zone was 0.46, 2.3, 4.5, 6.7, 8.4 and 10.2 me cm⁻³ in 0.4, 2, 4, 6, 8 and 10 dS m⁻¹ ECiw treatments, respectively. The grain production per unit evapotranspiration ( \textWP_{\textET\texta} {\text{WP}}_{{{\text{ET}}_{\text{a}} }} ) value of 2.56 in ECiw of 0.4 dS m⁻¹ treatment declined to 1.31 with ECiw of 2 dS m⁻¹. The \textWP_{\textET\texta} {\text{WP}}_{{{\text{ET}}_{\text{a}} }} reduced to one-fifth when percolation was included in the productivity determination. Similarly, the water productivity in respect of total dry matter production (TDM) was also reduced in different treatments. Therefore, the model predicted values of water balance can be effectively utilized to calculate the water productivity of rice crop.     

The effect of an external electric field on solid-state phase transition of (P(VDF/TrFE)(72/28)

The copolymers of vinylidene fluoride and trifluoroethylene (P(VDF/TrFE)) with VDF content of 50–80 mole % can be applied to the field of nonvolatile ferroelectric polymeric random access memory (FePoRAM) devices, since they exhibit stable ferroelectricβ-phase at room temperature with spontaneous polarization of the C-F dipoles towards an external electric field greater than the coercive field. Many researchers have already reported the molecular structures and dynamics of the ferroelectric (F) crystalline phase and the unique change in chain conformation between polarF phase and non-polar paraelectric (P) phase near their Curie transition temperature (T _c) which is dependent on factors such as VDF content and annealing treatment conditions. The effect of external electric field strength on theF⇔P crystalline phase transition in P(VDF/TrFE)(72/28) random copolymer samples of nanometer thickness was investigated. Capacitance of 250 nm thick sample measured as a function of heating-cooling under varying external electric field strength exhibited increasingT _c’s during heating (T _c ^↑ ) and cooling (T _c ^↓ ) under an applied electric field of more than 0.03 MV/cm. Applying cyclic bias electric field (+1 to −1 MV/cm) for samples kept isothermally at just above theirT _c(T _c ^↓ ) during cooling, we were able to observe the field-inducedP→F phase transition. With increasing cycles of the applied electric field for sample maintained just above (T _c ^↓ ), the bistableC-E hysteresis was observed and the phase change fromP→F is irreversible even after the electric field is removed. However, for samples kept well above (T _c ^↓ ) and nearT _m (100 °C and 120°C respectively) during cooling, theF-phase initially formed through the field-induced phase transition is reversibly transformed to theP-phase when the applied electric field is removed. Drastic changes were observed in both coercive field (E _c) and remanent polarization (P _r) values during heating and cooling near theT _c range due to theF⇔P phase transition and the results are reported in detail here.     

Functional Antibacterial Finishing of Woolen Fabrics Using Ultrasound Technology

The growing concern for the personal health and hygiene has created the necessity of acquiring wool fabric antibacterial activity. Silicon dioxide nanoparticles (SiO₂ NPs) have appropriate features to enhance the functional properties of wool fabrics, especially with polymer application. In this study efficient coating using polyethylene glycol (PEG₂₀₀₀) and SiO₂ NPs were used for imparting antibacterial properties to treated fabrics. All the treatments were carried out using both conventional and ultrasound techniques. The physical and chemical properties were evaluated using FTIR, XRD, and SEM. The result indicated that treated wool fabrics by PEG/SiO₂ NPs improved the dyeability and antibacterial of the fabrics and also enhanced its mechanical properties. Furthermore, it is believed that the ultrasound radiation causes homogeneous distribution of cross-links and polymerization throughout the wool surface. This offers considerable advantages compared to conventional treatment.     

Effects of fabric surface energy on human thermophysiological responses during exercise and recovery

The present paper reports a study on influences of fabric surface energy of cotton and polyester garments on clothing microclimates and human thermophysiological responses during intermittent exercise and recovery. Eight healthy males wearing the garments prepared performed exercises and rest according to the following protocol: rest for 30 min, run on treadmill for total 60 min of three sessions with different intensity and duration, and then sit quietly for 30 min for recovery, all at 30 °C and relative humidity of 30 %, while the microclimate humidity (H _mc ) and temperature (T _mc ), the clothing outside surface humidity (H _co ) and temperature (T _co ), the skin temperatures and ear canal temperature (T _{ear_canal} ) were measured. The garments are made of: (a) hydrophilic and hydrophobic cotton knitted fabrics, and (b) hydrophilic and hydrophobic polyester knitted fabrics. During and after exercise, for cotton, hydrophilic garment resulted in significant lowerΔH _mc , ΔH _co , ΔT _mc during recovery, higher , lowerΔT _{ear_canal} andΔT _forehead . For polyester, hydrophilic garment resulted in significantly lowerΔH _co , ΔT _co , higher , higherΔT _forehead during E1, E2 and recovery session but lower during E3. In summary, surface energy of cotton garments had significant influences on human thermophysiological responses during exercise and recovery, and hydrophilic cotton garment was better than hydrophobic one to reduce heat stress. Surface energy of polyester garments had influences of lower significance, and hydrophilic garment appeared better than hydrophobic garment.     

Comparision of the properties of UV-cured polyurethane acrylates containing different diisocyanates and low molecular weight diols

UV-curable polyurethane acrylate prepolymers were prepared from diisocyanates [isophorone diisocyanate (IPDI), 2,4-toluene diisocyanate (TDI), or 4,4′-dicyclohexylmethane diisocyanate (H₁₂MDI)], diols [ethylene glycol (EG), 1,4-butane diol (BD), or 1,6-hexane diol (HD)], polypropylene glycol as a polyol. UV-curable mixtures were formulated from the prepolymer (90 wt%), reactive diluent monomer trimethylol propane triacrylate (10 wt%), and photoinitiator 1-hydroxycyclohexyl ketone (3 wt% based on prepolymer/diluent). The effects of different diisocyanates/low molecular weigh diol on the dynamic mechanical thermal properties and elastic recovery of UV-cured polyurethane acrylate films were examined. The tensile storage modulus increased a little in the order of EG>BD>HD at the same diisocyanate. Two loss modulus peaks for all samples are observed owing to the glass transition of soft segments (T _gs ) and the glass transition temperature of hard segments (T _gh ). For the same diisocyanate,T _gs decreased, however,T _gh increased, in the order of HD>BD>EG. The elastic recovery also increased in the order of HD>BD>EG at the same diisocyanate. In case of same diols,T _gh increased in the order of H₁₂MDI>TDI>IPDI significantly. The ultimate elongation and elastic recovery increased in the order of TDI>IPDI>H₁₂MDI at the same diol.     

Preparation and dielectric properties of polyvinyl alcohol (Co,Zn Acetate) Fiber/n-Si and polyvinyl alcohol (Ni,Zn Acetate)/n-Si Schottky diodes

Dielectric properties and ac electrical conductivity (σ _ac ) of Au/PVA(Co, Zn acetate)/n-Si and Au/PVA(Ni, Zn acetate)/n-Si Schottky diodes (SDs) have been investigated in dark and under illumination by using experimental capacitance-voltage (C-V) and conductance-voltage (G/ω-V) measurements at 1 MHz and room temperature. Experimental results indicate that the change in dielectric constant (ɛ′), dielectric loss (ɛ″), loss tangent (tanδ), the real (M′) and imaginary (M″) parts of electric modulus and ac electrical conductivity (σ _ac ) with illumination were found to change linearly with illumination level (P). On the other hand, the ɛ′, ɛ″, tanδ and σ _ac vs P have positive slope while the M′ and M″ vs P have negative slope. Such behavior of dielectric properties and σ _ac can be attributed to illumination induced electron-hole pairs under illumination effect in the depletion region of SDs. The obtained results under illumination suggest that these devices can be used as a sensor in optical applications.     

外源丙三醇对干旱胁迫下玉米幼苗抗逆调控作用

以郑单958幼苗为试验材料,设置空白对照(CK)、正常水分条件下1 mmol/L丙三醇(Gly)处理玉米幼苗叶片、20%聚乙二醇(PEG-6000)模拟干旱胁迫(PEG)、20%聚乙二醇模拟干旱胁迫+1 mmol/L丙三醇(PEG+Gly)处理玉米幼苗叶片4个处理展开试验。结果表明,干旱胁迫下外源施用1 mmol/L丙三醇能显著提高叶片超氧化物歧化酶(SOD)、过氧化物酶(POD)、过氧化氢酶(CAT)和抗坏血酸过氧化物酶(APX)活性;丙二醛(MDA)和过氧化氢(H₂O₂)积累减少;最大光量子效率(F_v/F_m)和光系统Ⅱ潜在活性(F_v/F_o)显著提高,玉米幼苗叶片的净光合速率(P_n)、气孔导度(G_s)和蒸腾速率(T_r)、相对含水率及生长指标均显著提高,胞间CO₂浓度(C_i)降低。因此,外源施用丙三醇能通过降低叶片的氧化损伤和提高细胞保水能力来改善...