竹节对竹材力学强度影响的研究

本文对毛竹和刚竹的带节材与不带节竹材的主要力学性质研究表明,带节竹材的抗弯强度、顺纹抗压、抗剪、抗拉强度和冲击韧性都有一定程度降低的趋向,但抗劈开强度和横纹抗拉强度却有明显提高。影响竹材力学强度的主要因素是维管束数量、维管束排列方向及维管束中纤维的力学强度,了解这些规律,对复合材料的结构仿生有重要参考作用。     

人工林落羽杉力学性能研究

对江汉平原人工林落羽杉物理力学性能进行了研究,结果表明:落羽杉的气干密度为0.413 g/cm3,气干密度等级为轻;综合强度为74 MPa,强度等级为Ⅰ级;径向横纹抗压强度略大于弦向横纹抗压强度;端面硬度最高,弦面硬度与径面硬度差别不大。落羽杉南北面近树皮处木材的密度、抗弯强度、弹性模量、顺纹抗压强度均大于近髓心处,南北方向对落羽杉的密度、顺纹抗压强度在5%水平上差异均不显著,而对其抗弯强度、弹性模量在1%水平上差异显著。     

人工林杉木和杨树木材物理力学性质的株内变异研究

按照中国国家标准研究杉木和I-214杨树木材的抗弯弹性模量、抗弯强度、顺纹抗压强度和密度,同时按照日本国家标准研究2个树种的顺纹抗剪强度.结果表明:杉木的抗弯强度、顺纹抗压强度和密度由胸高直径处向上呈波浪形增加,抗弯弹性模量则稳定降低,但不同高度间杉木的物理力学性质没有显著差异;近树皮处木材的物理力学性质高于近髓心处木材,并有极显著差异.对于I-214杨树,只有抗弯弹性模量从髓心到树皮逐渐增加,其他的物理力学性质,最小值在从髓心到树皮的过渡区,最大值在近树皮处,从髓心到树皮,杨树的物理力学性质有极显著的差异.杉木和杨树的径面顺纹抗剪强度从髓心到树皮有极显著差异,并且近树皮的高于近髓心的木材,而弦面顺纹抗剪强度从髓心到树皮没有显著差异.木材密度与力学性质有很好的线性相关关系,木材密度是一个很好的力学强度的预测手段.     

天目铁木物理力学性质初步分析

对天目铁木进行物理力学性质测试与分析,结果表明,天目铁木木材的气干密度为0.721g.cm-3,弹性模量11.2Gpa,弦向抗弯强度104.9Mpa,顺纹抗压强度46Mpa,顺纹抗拉强度126.7Mpa,综合强度为150.9MPa,物理力学性能属于中等。     

Strength properties of thermally modified softwoods and its relation to polymeric structural wood constituents

Thermal modification at relatively high temperatures (ranging from 150 to 260 °C) is an effective method to improve the dimensional stability and resistance against fungal attack. This study was performed to investigate the impact of heat treatment on the mechanical properties of wood. An industrially-used two-stage heat treatment method under relative mild conditions (< 200 °C) was used to treat the boards. Heat treatment revealed a clear effect on the mechanical properties of softwood species. The tensile strength parallel to the grain showed a rather large decrease, whereas the compressive strength parallel to the fibre increased after heat treatment. The bending strength, which is a combination of the tensile stress, compressive stress and shear stress, was lower after heat treatment. This decrease was less than the decrease of only the tensile strength. The impact strength showed a rather large decrease after heat treatment. An increase of the modulus of elasticity during the bending test has been noticed after heat treatment. Changes and/or modifications of the main wood components appear to be involved in the effects of heat treatment on the mechanical properties. The possible effect of degradation and modification of hemicelluloses, degradation and/or crystallization of amorphous cellulose, and polycondensation reactions of lignin on the mechanical properties of heat treated wood have been discussed. The effect of natural defects, such as knots, resin pockets, abnormal slope of grain and reaction wood, on the strength properties of wood appeared to be affected by heat treatment. Nevertheless, heat treated timber shows potential for use in constructions, but it is important to carefully consider the stresses that occur in a construction and some practical consequences when heat treated timber is used.     

红壳竹人工林竹材物理力学性质的研究

测试了红壳竹人工林竹材的物理力学性质。结果表明：竹龄对红壳竹竹材的物理力学性质有显著的影响；竹材的径向、弦向、体积全干缩率随竹龄增加逐渐减少；基本密度、顺纹抗压强度、顺纹抗拉强度和抗弯强度都随竹龄增加而提高，至5－6年生强度稳定在较高的水平上，竹午由下至上，含水率、体积全干缩率逐渐减少；维管束密度、基本密度及力学强度相应提高。     

Quantitative Analysis on Measure Results by Resistograh for Wood Decay of Ancient Architecture

INTRODUCTION The main body of ancient architecture is wood construction in China, and the main bearing components of the buildings usually use timber, such as pillar, beam, purlin, crossbeam and rafter. Timber is a kind of biomaterial and will be damaged by fungal attack or insects after long time use, which will cause wood frames destroyed ultimately. Timber decay not only exists in its surface, but also usually begins with the inner of wood. It is therefore imperative to consider using …     

Strength and stiffness capacity utilisation of timber members in roof truss structures

The main objective of this study was to determine which property, of the six strength and stiffness properties used in structural timber design, was the most influential in the design of nail-plated roof trusses. Thirty recently completed nail-plated roof truss designs were randomly selected from three roof truss manufacturing plants and a total of 8 758 individual truss members were analysed for bending stress, shear stress parallel to grain, tensile stress parallel to grain, compression stress parallel to grain and deflection. The mean strength and stiffness capacity utilised of all the different design properties was well below 50% for all of the different dimension classes. Of all the individual strength properties, the mean bending strength capacity utilised per member was found to be the highest. The results of this study can be used for decision support related to wood property evaluation through? out the structural lumber value chain where roof truss members are the end products.     

湿地松与马尾松人工林木材物理力学性质的比较研究

通过对湿地松和马尾松人工林木材物理力学性质的测定和比较分析,结果表明:湿地松人工林木材密度、干缩系数和除冲击韧性以外的力学强度均稍大于马尾松人工林木材,而冲击韧性则恰恰相反.经差异显著性t检验表明:湿地松和马尾松木材物理力学性质指标中顺纹抗压强度、抗弯强度、弦面顺纹抗剪强度和冲击韧性差异极显著,气干密度、基本密度、径面顺纹抗剪强度和端面硬度差异显著,除此之外的其余指标差异不显著.     

江汉平原水杉、池杉、落羽杉物理力学性能比较研究

对江汉平原水杉、池杉、落羽杉人工林物理力学性能进行了研究,结果表明:落羽杉的密度和硬度最大;落羽杉、水杉、池杉的抗弯强度差异不大;水杉的弹性模量最大,约为落羽杉的2.3倍,落羽杉的弹性模量与池杉的比较接近。南北方向对水杉、池杉、落羽杉的密度、顺纹抗压强度在5%水平上差异均不显著,对池杉、水杉抗弯强度在5%水平上差异不显著,对落羽杉抗弯强度在1%水平上差异显著,对落羽杉、池杉的弹性模量在1%水平上差异显著,对水杉的弹性模量在5%水平上差异不显著。三杉南北面近树皮处木材的密度、抗弯强度、弹性模量、顺纹抗压强度均大于髓心处。对水杉、池杉、落羽杉物理力学性能比较研究,旨在为其培育及合理利用提供依据。     

毛竹不同种源竹材物理力学性质初步研究

通过对来自福建建瓯试验地16个毛竹种源竹材的密度、顺纹抗压强度、顺纹抗剪强度、顺纹抗拉强度和弦向抗弯强度及其弹性模量等物理力学性质的初步研究,结果表明:竹材物理力学性质在各种源之间存在一定的差异,其中湖南株洲的毛竹竹材物理力学性质比于其它种源的毛竹要好,而安徽霍山的毛竹竹材的物理力学性质较差,测量的各指标中有基本密度、抗剪强度、抗拉强度三项指标都达到最低;竹材密度的大小、抗拉强度的高低随种源纬度的降低而呈降低的趋势,而竹材的抗剪强度呈与之相反的趋势。     

苦竹竹材化学与力学性质的相关性分析

测定了1-5年生苦竹秆上、中、基3个部位的顺纹抗压强度、顺纹抗拉强度、弦向抗弯强度租化学组成，并对其进行了相关分析，结果表明：顺纹抗拉强度与各化学组成均为显著相关，顺纹抗压强度与纤维素的质量分数达显著相关，木质素和苯-醇抽提物的质量分数与力学强度为正相关，纤维素、灰分、热水抽出物、1％NaOH抽出物的质量分数与力学强度为负相关。     

KY-FW阻燃剂对木材力学性能的影响

采用杉木和泡桐为试材,对经过KY-FW阻燃剂处理的木材与未经处理的木材进行对比研究,分析KY-FW阻燃剂对木材力学性能的影响.结果表明,木材经KY-FW阻燃剂处理后,除冲击韧性降低外,其它主要力学性能指标(如抗弯强度、顺纹抗压强度及硬度)都有所提高.KY-FW阻燃木材的力学性能达到了一级水基型阻燃剂标准规定的相应指标.     

Effect of grain angle on shear strength of glued end grain to flat grain joints of defect-free softwood timber

To evaluate the effect of grain orientation on the adhesive bond strength, three-layered Norway spruce wood specimens were tested in shear. The two axial-oriented outer layers were jointed with the middle layer using three typical glues for load bearing constructions, i.e. one-component polyurethane (PUR), melamine–urea–formaldehyde (MUF) and phenol–resorcinol–formaldehyde (PRF). The grain orientation of the middle layers was varied from 0° (parallel to grain of the surface layer) to 90° (perpendicular to grain of the surface layer) in incremental steps of 10°. Samples with middle layers oriented parallel to the outer layers showed shear values in the range of solid spruce wood. Decreased shear strength values were expected for increased grain angles of the middle layer. However, no explicit tendency was observed for the shear strength in dependence of the grain direction. In general, MUF-bonded samples showed slightly higher shear strength values compared with PUR- and PRF-bonded specimens.     

Tensile strength of softwood butt end joints. Part 1: Effect of grain angle on adhesive bond strength

To study the effect of grain angle on the adhesive bond strength in wood, three-part Norway spruce wood specimens were bonded and tested in tension. The two axially orientated outer parts of the specimens were joined with the middle part by means of three adhesives typically used for load-bearing constructions, i.e. one-component polyurethane (PUR), melamine-urea-formaldehyde (MUF) and phenol-resorcinol-formaldehyde (PRF). The grain angle of the middle part was varied from 0° (end grain to end grain) to 90° (flat grain to end grain) in incremental steps of 10°. In general, PRF- and MUF-bonded samples exhibited highest tensile strength at end grain to end grain orientation of the three parts, while specimens bonded with PUR showed only 25% of the strength measured for PRF and MUF, respectively. At high grain angles (90°) all specimens showed similar strength values in the range of 30% of maximum strength of MUF- and PRF-bonded specimens. To explain the changing strength levels at different grain angle a composite failure criterion was applied.     

闽南格木木材物理力学性质的研究

通过对格木木材物理力学性质进行测定和分析,结果表明:格木木材密度大、变形大,其气干密度为0.857 g·cm-3,基本密度为0.746 g·cm-3,体积干缩系数为0.615,顺纹抗压强度为67.59 MPa,抗弯强度为141.82 MPa,综合强度为209.41 MPa,属于高。该研究结果解决了格木营林和木材利用上的一个基础性问题。     

COMPARATIVE STUDY OF WOOD PROPERTIES BETWEENWHITE WOOD OF DAHURIAN LARCH AND MONGOLIANSCOTCH PINE

DahurianlarchandMongolianscotchpinearetwomajorconunerciaIconilbroustTeesinDaxing'anlingForesnyArea.Itisob-viousthattbcwoodproPertiesandworkability'ofthetWoplantsarecompletelydifferent.Butlnrecert'years,ltlsfoundthattherearetwodiffer':nttypesinparameterofwood'scolour.phy'sicalandmechanicalproPertiesandwork-ability'inDahurianlarch,namelyredwoodandx"hite..od.l']Andthepropertiesofwhite`voodaresligl1tlyyellow-white,medianweightandhardness,goodinworkability'andLard-ness,goodinwodability'anduneas…     

Influence of Ammoniacal Copper Quaternary treatments on mechanical properties of blue-stained Lodgepole Pine wood

Three concentrations （2.8%, 2.0%, 1.2%） of Ammoniacal Copper Quaternary （ACQ） was selected to treat Lodgepole pine wood for evaluating ACQ treatment on mechanical properties of blue-stained wood. The bending modules of elasticity （MOE）, modules of rupture （MOR）, toughness and shearing strength parallel to grain on tangential surface, are tested according to the criteria GB1927-1943-91. Non-treated sample were also tested according to the same procedure. The results showed that the three groups specimen impregnated by different concentrations of ACQ solution met the AWPA standard 2003 of America （UC4A 6.4g/cm^3）. There were significant difference of toughness between treated wood and non-treated wood （p=0.01）, but there were no statistically significant differences among three concentrations in terms of toughness, and toughness of treated wood was approximately 20% lower than non-treated. MOR, MOE as well as sheafing strength parallel to grain were found to be not significantly different between treated wood and non-treated one, and there were no statistically significant difference among three concentrations of ACQ too. Toughness, MOR, MOE and sheafing strength parallel to grain increased with decrease of concentration of ACQ, but they were hardly affected by ACQ preservatives.     

桦木顺纹抗压强度的SEPA-VISSA-RVM近红外光谱预测

木材顺纹抗压强度是评价木材力学性能的重要指标,而传统测量方法操作复杂、精确度低。以桦木为例,提出基于近红外光谱技术(NIR)的SEPA-VISSA-RVM木材顺纹抗压强度模型,实现对其更加精确的预测。试验选取100个木材试件,在900~1700 nm近红外光谱波段上采集数据并测量抗压强度真值;然后采用卷积平滑(SG)方法进行光谱预处理;使用采样误差分布分析(SEPA)作为变量空间迭代收缩算法(VISSA)的改进策略进行特征波长优选;最后通过粒子群优化算法(PSO)优化核函数参数并建立相关向量机(RVM)的预测模型。试验表明:在特征波长优选方面,以偏最小二乘法(PLS)建模为基础的SEPA-VISSA方法,其预测决定系数为0.9593,预测均方根误差为2.8995,相对分析误差为3.0256,光谱变量数由512减小到111个,占总波长的22%,均优于VCPA、CARS和VISSA算法;在建模预测方面,以SEPA-VISSA所选波长为基础的RVM模型,PSO优化的拉普拉斯(Laplacian)核函数的核宽度为10.4043,决定系数为0.9449,预测均方根误差为2.0432,相对分析误差为4.2936,预测效果优于PLS和SVR。因此,基于近红外光谱的SEPA-VISSA-RVM建模能够实现对桦木顺纹抗压强度更准确和稳定的无损检测。     

Tensile strength of softwood butt end joints. Part 1: Effect of grain angle on adhesive bond strength

Abstract

To study the effect of grain angle on the adhesive bond strength in wood, three-part Norway spruce wood specimens were bonded and tested in tension. The two axially orientated outer parts of the specimens were joined with the middle part by means of three adhesives typically used for load-bearing constructions, i.e. one-component polyurethane (PUR), melamine–urea–formaldehyde (MUF) and phenol–resorcinol–formaldehyde (PRF). The grain angle of the middle part was varied from 0° (end grain to end grain) to 90° (flat grain to end grain) in incremental steps of 10°. In general, PRF- and MUF-bonded samples exhibited highest tensile strength at end grain to end grain orientation of the three parts, while specimens bonded with PUR showed only 25% of the strength measured for PRF and MUF, respectively. At high grain angles (90°) all specimens showed similar strength values in the range of 30% of maximum strength of MUF- and PRF-bonded specimens. To explain the changing strength levels at different grain angle a composite failure criterion was applied.