Evaluation of thermally modified beech and spruce wood and their properties by FT-NIR spectroscopy

Quality assessment of thermally modified spruce (Picea abies (L.) Karst) and beech (Fagus sylvatica L.) wood and of the corresponding reference samples was carried out by means of non-destructive FT-NIR spectroscopic measurements and PLS regression. Oven-dry and basic density as well as MOE and MOR determined by 3-point bending tests were evaluated. The focus was put on specimens produced from material that had been thermally modified in an industrial scale kiln. Modelling results range from poor to very good. The results of the spectra taken from the spruce samples resulted in better prediction results than the spectra of the beech samples. This could be due to different proveniences or variation in the industrial modification process. The results indicate that FT-NIR surface measurements of sound thermally modified wood samples could be applied to evaluate several characteristics before and after the modification process. The method could be used for screening during pre-sorting of thermally modified wood.     

Durability of thermally modified Norway spruce and Scots pine in above-ground conditions

Abstract

One of the main objectives of thermal modification is to increase the biological durability of wood. In this study the fungal resistance of Norway spruce and Scots pine, thermally modified at 195°C and 210°C, was studied with a lap-joint field test. Untreated pine and spruce and pine impregnated with tributyl tin oxide (TBTO) and copper, chromium and arsenic (CCA) were selected as reference materials. The evaluations were carried out after 1, 2 and 9 years of exposure. After 1 and 2 years of exposure mainly discoloration was detected. Only the untreated pine was slightly affected by decay fungi. There were significant differences in the decay ratings of untreated and thermally modified wood materials after 9 years in the field. While the untreated wood materials were severely attacked by decay fungi or reached failure rating, only small areas of incipient decay were detected in the thermally modified samples. Thermally modified pine was slightly more decayed than thermally modified spruce. The only wood material without any signs of decay was CCA-treated pine, since some of the TBTO-treated pine samples were also moderately attacked by fungal decay. The results of the lap-joint test had a good correlation with mass losses in a laboratory test with brown-rot fungi.     

Microstructure,strength and structural integrity of heat-treated beech and spruce wood

Abstract

Heat treatment of wood is an effective method by which to improve the dimensional stability and biological durability, but the mechanical strength is decreased at the same time. Besides chemical modification of cell-wall constituents, physical weakening of the microstructure owing to heat-induced defects may also contribute to strength loss. Therefore, anatomical properties of heat-treated beech (Fagus sylvatica L.) and spruce (Picea abies Karst.), studied by light microscopic and scanning electron microscopic analysis, and their interrelation with strength properties and structural integrity were investigated. For determination of structural integrity, the high-energy–multiple-impact (HEMI) test was applied. Microscopic analyses showed frequent formation of radial cracks in heat-treated beech close to the rays as well as tangential cracks in the latewood of spruce. In addition, the modulus of rupture was more affected by the heat treatments than the resistance to impact milling (RIM) determined by the HEMI test, because RIM is based on multiple fractures on the microlevel that are not affected by the formation of intercellular cracks or other defects due to the heat treatment. It was concluded that heat-induced defects in the wood microstructure contribute to the substantial strength loss of thermally modified timber.     

H-NMR studies of water interactions in sitka spruce and western hemlock: moisture content determination and second moments

Summary The purpose of this study was to examine the influence of the moisture level on the cell-wall material in wood using pulsed proton nuclear magnetic resonance. The wood species used were western hemlock (Tsuga heterophylla (Raf.) Sarg.) and sitka spruce (Picea sitchensis (Bong.) Carr.), distinguishing between heartwood and sapwood regions. The moisture contents of the specimens were below the fibre saturation point and they were conditioned to equilibrium moisture contents based on initial desorption, adsorption and secondary desorption processes. From the FID experiments, the NMR-based moisture contents and the solid-wood lineshape second moments were determined. Average relative proton-spin densities, which were needed to calculate the NMR-based moisture contents, were determined from known moisture contents and they were: hemlock sapwood: 0.616; hemlock heartwood: 0.537; spruce sapwood: 0.679; and, spruce heartwood: 0.446. The average RSD value, considering both heartwood and sapwood, for western hemlock species was 0.577 and for sitka spruce was 0.563; these are close to published RSD values for other species. The condition as to how the equilibrium moisture content was attained did not influence the second moment for hemlock; however, for spruce sapwood, the second moments were sorption dependent. The hemlock M₂ decreased from about 5.1 × 10⁹ s^-2 at low M_NMR to 4.5 × 10⁹ s^-2 (heartwood) and 4.3 × 10⁹ s^-2 (sapwood) at higher m_nmr. The adsorption and secondary desorption M₂ for the spruce sapwood region decreased from about 5.0 × 10⁹ s^-2 at low m_nmr to about 4.1 × 10⁹ s^-2 near the M_F, whereas M₂ for the spruce heartwood decreased from about 4.3 × 10⁹ s^-2 at low M_NMR to about 3.5 × 10⁹ s^-2 near M_F. Extractives may have a key role in obtaining the RSD and second moments.This project was financially supported by the Science Council of British Columbia, MacMillan Bloedel Research. The Natural Sciences and Engineering Research Council of Canada is acknowledged for their support of the NMR spectrometer measurements     

Geological controls on conifer distributions and their implications for forest management in Finnish Lapland

Abstract

Soil water and nutrient regimes of naturally established old-growth conifer stands and those of intensively managed Norway spruce [Picea abies (L.) Karst.] sites were assessed over a range of lithological provinces in Finnish Lapland. Soil dielectric permittivity (ε), as a measure of soil water content (θ _v) and soil electrical conductivity (σ _a), as a measure of soil solute content, were species specific, such that high soil θ _v>0.27 cm³cm^?3 (ε>15) constitutes an edaphic constraint for Scots pine (Pinus sylvestris L.) and low soil solute content (σ _a<0.5 mS m^?1) is constraining for Norway spruce. The spatial pattern of the soil θ _v was temporally stabile, such that intraseasonal and interseasonal soil θ _v was significantly higher in silty tills of spruce stands compared to sandy tills of pine stands. Scots pine was the only conifer on tills derived from felsic rocks of Hetta granite (HG) and Lapland granulite (LG). Norway spruce dominated on tills derived from the mafic rocks of Lapland greenstone belt (LGB), but tills of LG and HG constitute a dispersal barrier for spruce. Mechanical site preparation (MSP) with ploughing (Marttiini) was not able to amend soil θ _v to meet site requirements of Scots pine at former spruce sites. MSP resulted in significant reduction in soil nutrient content such that untreated control σ _a>tilt/shoulder σ _a>trench σ _a. The results imply that MSP treatments through which cross-contour tracks are created pose a risk to the sustainability of soil quality in Lapland.     

Influence of Log Characteristics on Drum Debarking of Pulpwood

Properties of 200 poorly debarked softwood logs were studied in order to examine how different log characteristics affect drum debarking of mixed pine (Pinus sylvestris L.) and spruce [Picea abies (L.) Karst] pulpwood during the summer. The definition of a poorly debarked log and the sampling criterion was that >10 dm² bark remained on the log surface. The average share of poorly debarked logs was 8% and the most frequent log type was breakage logs. The main species among the poorly debarked logs was spruce and the mean wood moisture content was considerably lower than for the pulpwood chips. Many logs were affected by root rot or were damaged by harvesting equipment, resulting in reduced moisture content and, consequently, in increased bark/wood shear strength. Bark from the poorly debarked logs contributed to approximately 68% of the bark content in the chips. By avoiding air-drying of pulpwood, or by sorting pulpwood prior to debarking, the bark content in chips might be substantially reduced, which would improve the purity of the pulp and decrease production costs.     

Gluability of thermally modified beech (Fagus silvatica L.) and birch (Betula pubescens Ehrh.) wood

Abstract

One of the main disadvantages of wood is hygroscopicity resulting from its polar character. The sorption–desorption of water causes unwanted swelling and shrinkage in wood. Thermal modification substantially reduces this inconvenient feature. Unfortunately, the same chemical changes that reduce water sorption alter the polar character of the material and result in poorer wetting of thermally treated wood by waterborne adhesives. Gluability of thermally modified beech (Fagus silvatica L.) and birch (Betula pubescens Ehrh.) wood with two commercial amino resins, melamine–urea–formaldehyde (MUF) and melamine–formaldehyde (MF), and a two-component polyurethane (PUR) adhesive was investigated. Both wood species were modified according to two temperature regimes: 160°C and 190°C. Shear strengths of the joints were then determined according to EN 205:2003 standard. The results showed that thermally modified beech and birch wood can be effectively glued not only with commercially available PUR adhesives, but also with aqueous MF and MUF resins. The resultant shear strengths of the joints were limited by the strength of the thermally modified substrate.     

Air-coupled ultrasound and electrical impedance analyses of normally dried and thermally modified Scots pine (Pinus sylvestris)

Wood is graded according to strength in various applications. The ultimate strength can only be determined by breaking the specimen, and thus other characteristics like density and modulus of elasticity (MOE) are used for estimation of the strength. In this study, the properties of normally dried and thermally modified Scots pine were studied using electrical impedance and air-coupled ultrasound (ACU) methods. Density, hardness, MOE and strength were analysed and compared with the electrical and ultrasonic responses. The measurements were conducted in stable laboratory conditions with well equilibrated samples and the moisture content was not determined. Both the ultrasonic and electrical parameters correlated with the density and mechanical properties. Using multivariate analysis, density could be estimated with accuracy of 21 kg/m³ (SD) for normally dried timber and 13 kg/m³ (SD) for thermally modified timber (TMT; N = 15). MOE could be estimated with accuracy of 0.7 kN/mm² (SD) for normally dried timber and 1 kN/mm² (SD) for TMT (N = 14). According to the study, electrical impedance spectroscopy combined with ACU measured across the grain is a potential non-destructive technique for the strength estimation of wood.     

Colour responses from wood,thermally modified in superheated steam and pressurized steam atmospheres

Abstract

In this study, two different methods were used to produce thermally modified wood. One was carried out in a typical kiln drying chamber using superheated steam (SS) and the other used pressurized steam in an autoclave cylinder (PS). Overall, both processes followed the same principles and the wood was not treated with any chemicals. Two wood species were studied, Scots pine (Pinus sylvestris) and Norway spruce (Picea abies). Treatments in the autoclave were carried out under pressure using temperatures of 160°C, 170°C and 180°C. Temperatures of 190°C and 212°C were used in treatments in the chamber at normal air pressure. The colour was measured using L*C*H colour space. Results for both species showed that similar L* (lightness) can be reached at lower (20–30°C) temperatures using PS compared with SS treatment. The hue angle of PS-treated wood was smaller than that of SS-treated wood. No significant difference in C* (chroma) was detected. The difference in E value between PS- and SS-treated wood was smaller for Norway spruce than for Scots pine. The residual moisture content was about 10% higher in wood treated by the PS process compared with the SS process.     

Durability of thermally modified sapwood and heartwood of Scots pine and Norway spruce in the modified double layer test

In the present study, durability of untreated and thermally modified sapwood and heartwood of Scots pine and Norway spruce was examined using a modified double layer test. Base layer samples were partly on contact with ground where exposure conditions were harder than that in a double layer test above the ground. The base layer on ground contact gave results already after one year of exposure in Finnish climate, but the top layer of a double layer test element simulated more the situation of decking exposure.

Significant differences in durability and moisture content (MC) between the wood materials were detected after six years of exposure in the field. Thermally modified pine heartwood performed very well in all layers of the test element and only minor signs of decay were found in some of the base samples. Both sapwood and heartwood of thermally modified spruce were suffering only slight amounts of decay while thermally modified pine sapwood was slightly or moderately decayed. Untreated sapwood samples of pine and spruce were severely decayed or reached failure rating after six years in the field. Untreated heartwood samples performed clearly better. The highest MCs were measured from untreated and thermally modified pine samples. Thermal modification increased significantly the durability and decreased the MC values of all wood materials.     

Functions for Biomass Estimation of Young Pinus sylvestris,Picea abies and Betula spp. from Stands in Northern Sweden with High Stand Densities

New silvicultural regimes with high within-stand competition require new functions for estimation of standing stock and growth of biomass components, since the allometry of trees is changed by light competition. This paper presents functions for estimation of the aboveground biomass dry weights for stem wood, stem bark, branches and leaves of young (diameter at breast height <10 cm) Scots pine (Pinus sylvestris L.), Norway spruce [Picea abies (L.) Karst.] and birch (Betula pendula Roth. and Betula pubescens Ehrh.) trees growing in dense mixed stands. The functions were derived from a sample consisting of 84 Scots pine, 43 Norway spruce and 66 birch trees from six stands in northern Sweden with high stand densities (>10000 st ha^-1). The logarithmically transformed power function displayed a good ability to stabilize the variance of dry weights and showed a good fit to the material (0.37< R ² <0.99). A comparison with the most commonly used biomass functions in Sweden today showed that they overestimated the weight of stem wood and branches, while the weight of foliage was underestimated. The nature of these discrepancies suggested that the precision of biomass estimations might also be improved for young trees at wider spacing.     

The effect of axial strain on crystalline cellulose in Norway spruce

The effect of strain on dry, clear Norway spruce (Picea abies [L.] Karst.) wood was studied by tensile testing along the cell axis and by in situ X-ray diffraction measurements. The mean microfibril angle (MFA) was initially 3–12 degrees and did not decrease due to strain. Based on the positions of the reflections 200 and 004 of crystalline cellulose, cellulose chains elongated and the distance between the hydrogen bonded sheets of chains decreased due to the strain. The elongation of the unit cell parallel to the cellulose chains was twice as high in juvenile wood as in mature wood. The (X-ray) Poisson ratio ν _ca for crystalline cellulose in Norway spruce was calculated from the deformation of the unit cell. The average ν _ca of earlywood was 0.28 ± 0.10 in juvenile wood and 0.38 ± 0.23 in mature wood. In latewood, the average ν _ca was 0.48 ± 0.10 in juvenile wood and 0.82 ± 0.11 in mature wood. The average ν _ca values were not directly correlated to the crystallite dimensions or to the mean MFA in juvenile and mature earlywood and latewood. The results show that the amorphous matrix has a definite effect on the deformation of cellulose crystallites.     

Effects of UV light irradiation on colour stability of thermally modified, copper ethanolamine treated and non-modified wood: EPR and DRIFT spectroscopic studies

A series of experiments were carried out to investigate the colour stability of chemically treated and thermally modified wood compared to non-modified wood during long term artificial UV light irradiation. One set of wood samples was vacuum-pressure impregnated with alkaline (pH 9.8) copper (II) ethanolamine aqueous solution, while another set of samples from the same wood block was thermally modified at 210°C and −0.90 bar for 2 h. The treated and modified wood samples along with the non-modified ones were exposed to artificial UV light with the wave length in the region of UVA (315–400 nm) and UVB (280–315 nm) intermittently for 500 h. Colour measurements were carried out throughout the irradiation period at an interval of 100 h according to CIEL*a*b* system, where the results are presented in terms of ΔE, ΔL*, Δa* and Δb* values. Better photo-stability in terms of colour changes was recorded for both treated and modified woods compared to the non-modified one. By means of EPR and DRIFT spectroscopic study it was shown that some degree of colour stability of treated and modified woods, achieved during artificial UV light irradiation, resulted from lignin modifications and monomers of phenolic compounds.     

Surface mould growth on wooden claddings – effects of transient wetting,relative humidity,temperature and material properties

ABSTRACT

Effects of climatic factors and material properties on the development of surface mould growth on wooden claddings were investigated in a laboratory experiment. Specimens of aspen (Populus tremula), Siberian larch (Larix Sibirica), American white oak (Querqus alba), Scots pine (Pinus sylvestris), Norway spruce (Picea abies) and thermally modified pine were incubated in eight climatic chambers at specified wetting periods (2 or 4?h per day), relative humidity (58–86%) and temperature conditions (10–27°C). Surface mould growth was assessed weekly for 13 weeks, and the results were evaluated statistically using Generalized Estimating Equations logistic regression models. All tested climatic factors had significant effects on the mould growth, and there were significant differences between the materials. The ranking of the materials varied with temperature and over time. Aspen, pine sapwood and oak were overall most susceptible to mould growth, and thermally modified pine least susceptible. There were significant differences between sapwood and heartwood for pine and spruce. The effect of density was tested on the spruce heartwood material, but was not found to be significant. The results can be used to further develop prediction models for mould growth on wooden claddings.     

Influence of a long-term storage in anaerobic conditions on Norway spruce (Picea abies,L. Karst.) physical and mechanical wood properties

Timber storage is a key aspect of storm damage management. After huge storms, sprinkling storage is usually the most used conservation process but anaerobic storage in sealed silos appears as good alternative to preserve wood quality over long periods. This paper investigates the impact of long-term (57 months) storage of Norway spruce logs in anaerobic atmosphere on wood properties. Tests were performed on clear wood specimens and on lumbers to determine the modulus of elasticity (E), the static bending strength (σ_f) and the dynamic bending strength (K). Storage effects on impregnability and colour variation were also studied. Results show no effect of storage on E, σ_f and K. The naturally poor impregnability of Norway spruce is not improved by the anaerobic conditions, compared to traditional wet storage. Triangle tests reveal no discernible colour variation between logs that underwent anaerobic storage and the control sample. As a conclusion, despite a mould (Gliocladium solani) frequently observed on logs surface after the storage, the process offers ideal conservation conditions. While overall cost remains the main drawback for using anaerobic storage at large scale, the process can be recommended for high value logs, especially since it has few environmental impacts.     

Application of the SB distribution to the prediction of concomitant wood properties

Summary It is frequently the case that multiple strength properties of structural wood members are simultaneously needed in design or research. A method has been developed to predict the probability distribution of concomitant material properties of wood from a knowledge of some correlated, nondestructive material property. The method developed in this study is based on properties of the univariate S_B distribution and the bivariate S_BB distribution. The technique involves a priori knowledge of the correlation relationship between a nondestructive parameter and the strength parameter for the two concomitant properties in question. A relationship is developed between the two nondestructive parameters and a simulation procedure is presented to predict either concomitant property from a single nondestructive measurement. The results showed that when a single parameter was predicted directly from a correlated variable, the simulated and experimental distributions were very similar (average error 3–4%). This result confirms previous findings. For the prediction of the concomitant property from an indirect relationship with another parameter, the absolute value of the average error was about 13%.     

Variation in properties of Phlebiopsis gigantea related to biocontrol against infection by Heterobasidion spp. in Norway spruce stumps

The properties of 64 heterokaryotic strains of Phlebiopsis gigantea, isolated mostly from Norway spruce stumps, were tested for asexual spore production, growth rate and competitive ability against Heterobasidion spp. on agar medium, and for growth rate in spruce wood. Eighteen isolates were also tested for the efficacy of control against Heterobasidion spp. in stem pieces of spruce. The results revealed high variation in traits between different P. gigantea isolates. The efficacy of control against Heterobasidion spp. and the growth rate in spruce wood were closely related to each other (r = 0.727, p < 0.001). These preliminary tests indicate that the growth rate of a P. gigantea strain in spruce wood is the most important characteristic determining its efficiency in controlling the infection and spread of Heterobasidion spp. in spruce stumps.     

Effect of fungal exposure on the strength of thermally modified Norway spruce and Scots pine

Abstract

Thermal modification at elevated temperatures changes the chemical, biological and physical properties of wood. In this study, the effects of the level of thermal modification and the decay exposure (natural durability against soft-rot microfungi) on the modulus of elasticity (MOE) and modulus of rupture (MOR) of the sapwood and heartwood of Scots pine and Norway spruce were investigated with a static bending test using a central loading method in accordance with EN 408 (1995). The results were compared with four reference wood species: Siberian larch, bangkirai, merbau and western red cedar. In general, both the thermal modification and the decay exposure decreased the strength properties. On average, the higher the thermal modification temperature, the more MOE and MOR decreased with unexposed samples and increased with decayed samples, compared with the unmodified reference samples. The strength of bangkirai was least reduced in the group of the reference wood species. On average, untreated wood material will be stronger than thermally modified wood material until wood is exposed to decaying fungi. Thermal modification at high temperatures over 210°C very effectively prevents wood from decay; however, strength properties are then affected by thermal modification itself.     

Distribution of preservatives in thermally modified Scots pine and Norway spruce sapwood

Studying the impregnation and distribution of oil-based preservative in dried wood is complicated as wood is a nonhomogeneous, hygroscopic and porous material, and especially of anisotropic nature. However, this study is important since it has influence on the durability of wood. To enhance the durability of thermally modified wood, a new method for preservative impregnation is introduced, avoiding the need for external pressure or vacuum. This article presents a study on preservative distribution in thermally treated Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) Karst.) sapwood using computed tomography scanning, light microscopy, and scanning electron microscopy. Secondary treatment of thermally modified wood was performed on a laboratory scale by impregnation with two types of preservatives, viz. Elit Träskydd (Beckers) and pine tar (tar), to evaluate their distribution in the wood cells. Preservative solutions were impregnated in the wood using a simple and effective method. Samples were preheated to 170 °C in a drying oven and immediately submerged in preservative solutions for simultaneous impregnation and cooling. Tar penetration was found higher than Beckers, and their distribution decreased with increasing sample length. Owing to some anatomical properties, uptake of preservatives was low in spruce. Besides, dry-induced interstitial spaces, which are proven important flow paths for seasoned wood, were not observed in this species.     

Genetic parameters of growth and wood quality traits in Picea abies

Genetic parameters were estimated for wood and growth traits in two 19-yr-old clonal trials and a 40-yr-old full-sib progeny trial of Norway spruce [Picea abies (L.) Karst.]. In the clonal trials high (>0.4) broad-sense heritabilities were found for wood density traits, lignin content, number of internal cracks, growth traits, spiral grain and number of resin canals. Moderate (0.2–0.4) heritabilities were found for tracheid lumen diameter and cell wall thickness, microfibril angle and tracheid length, while low heritabilities (<0.2) were found for pulp yield, fibre strength, wood stiffness and wood colour. Lignin content and pulp yield showed low genetic variation, whereas the genotypic coefficient of variation for most other traits ranged between 5 and 15%. Most traits showed low levels of genotype by environment interaction. Among the wood properties, latewood proportion, earlywood density and ring density showed significant, adverse correlations with volume in both clonal trials.