造林密度对马尾松木材主要性质影响的研究

本文对贵州省龙里林场马尾松密度试验林 ,5种造林密度 ,15年生马尾松木材基本密度、生长轮宽度、晚材率和解剖特性进行研究。结果表明 :造林密度对马尾松生长轮宽度、晚材率和管胞列数影响较大 ,方差分析达到显著水平。造林密度大 ,则生长轮变窄 ,管胞列数减少 ,晚材率增加。造林密度对马尾松木材基本密度的影响不显著 ,但具明显的规律性 ,即随着造林密度加大木材基本密度增加 ,造林密度过大反而下降。造林密度对管胞形态的影响表现出因树龄而异 ,不同造林密度马尾松管胞形态总平均值变化不大 ,但管胞长度随树龄的增大而增加的趋势受到造林密度影响。较低的造林密度各生长轮管胞长度差异不显著。组织比量不受造林密度影响。     

施肥对中龄马尾松木材主要物理性质和管胞形态的影响

采用正交设计方差分析方法,研究了施肥对中龄马尾松木材主要物理性质和管胞形态的影响.结果表明施肥有助于增加生长轮宽度,提高晚材率,但经正交设计方差分析差异不显著.P肥使管胞宽度、腔径,尤其是径向腔径有所增加,但各处理间差异不显著.因此,可以认为施肥对管胞形态影响不大.施肥对木材基本密度的影响较复杂,似乎与肥料种类、施肥量,甚至与树干部位有关,P肥使下部木材基本密度显著增加,N、K肥对木材基本密度影响不大.     

马尾松纸浆林造林密度对木材性质的影响

本文研究了龙里林场5种造林密度，15年生马尾松纸浆林木材基干密度和管胞形态。结果表明：造林密度对木材基本密度影响不大，但具明显的趋势，即一定造林密度条件下，木材基本密度随造林密度增加而增加，造林密度对管胞形态的影响，表现出因年龄而异，不同造林密度马尾松管胞形态总平均值变化不大，但管胞长度随树龄的增大而增加的趋势，受到造林密度影响，较低的造林密度各生长轮管胞形态差异不显著。管胞长度频率分布具一定的规律，中等长度（2501－3500um)管胞长度频率分布最大，占总频率的45％－74．19％，随着造林密度加大，中等长度的管胞增加，较短管胞长度（≤2500um)减少。     

3个马尾松种源材性差异及相关性

以马尾松(Pinus massoniana)桐棉、古蓬、容县等3个种源为对象,比较了年轮宽度、晚材率、管胞形态、木材基本密度等指标的差异,并通过这些指标的相关关系导出了各个种源的密度回归模型。结果表明:种源间的年轮宽度和晚材率无显著差异且变异系数较大,其中容县种源年轮宽度最大,古蓬种源最小;容县种源平均晚材率最低,桐棉种源平均晚材率最高。种源间的管胞形态(管胞壁厚、管孔面积)和木材基本密度有显著差异,其中,容县种源的早材壁厚最厚,管孔面积最小,桐棉种源早材壁厚最薄,管孔面积最大;古蓬种源晚材壁厚最厚,管孔面积最小,容县种源晚材壁厚最薄,管孔面积与其他两个种源的平均值相似。古蓬种源平均基本密度最大为0.519 g/cm~3。上述材性指标间的相关性达显著或极显著水平。基于此,导出了以木材密度为因变量,考虑晚材率的管胞壁厚和管孔面积为自变量的三元三次方程回归模型,3个种源回归模型平均拟合度高于73%。     

森林培育措施对红松人工林径向生长性质的影响

对不同森林培育措施的红松人工林径向生长性质指标进行测试和分析.结果表明不同的森林培育措施(坡位、林分结构、初植密度、间伐)对红松人工林的生长率、生长轮宽度及生长轮密度有显著的影响,对晚材率的影响不明显;坡向对红松人工林的生长率、生长轮宽度有显著的影响,对晚材率、生长轮密度的影响不明显;修枝对红松人工林的生长率、晚材率有显著的影响,对生长轮宽度及生长轮密度的影响不明显;阴坡、坡下、三株一丛、2.0m×2.0m、适度间伐、适度修枝的林分林木生长率较高,可用于培育大径级的木材.     

广西马尾松纸浆材种源选择的初步研究

对广西南宁9年生马尾松种源林9个代表性种源的木材纤维形态、物理性质和化学组分27项性状分析表明,多数材性性状种源间差异远大于单株间差异,与木材造纸性能关系密切的双壁厚、壁腔比、管胞宽度等具中强度种源遗传力,晚材率、管胞长宽比等材性性状与高径生长具显著相关。据与木材造纸性能关系紧密的11项性状综合选出广东高州、广西宁明及贵州德江等造纸材优良种源。     

造林密度对马尾松林分生长木材造纸特性及经济效益的影响

贵州省龙里林场松造林密度试验林１５年的试验结果表明,密度对树高生长无明显影响;平均胸径、单株材积随密度的增加而减小,高径比和蓄积量则随密度的增大而增加,不同处理间的差异从６￣８年起达到显著或极显著水平。小径原木出材率随密度的增大明显降低,短小原木和薪材的出材率及出材量均随密度的增大而增加,各处理间的差异达到极显著水平。木材生长轮宽度随造林密度的增加而减小,晚材率和木材基本密度大体上随密度的增高而增     

章古台地区樟子松年轮宽度和管胞长度的径向变异

对章古台地区不同密度樟子人工林松年轮宽度和管胞长度进行测定,结果表明：章古台地区胸径年轮数30a的樟子松林,已出现生长衰退现象,生长衰退期开始林龄与林分密度有关,降低林分密度可延缓衰退期出现林龄。樟子松管胞长度与距离髓心的年轮数之间存在Y=alnx＋b（Y：管胞长度;X：距离髓心的年轮数．b：第1年轮的管胞长度）关系。不同密度樟子松年轮宽度不同,但管胞长度与未成熟材范围无显著变化,未成熟材范围距离髓心的年轮数均为21～23a。     

人工林马尾松木材性质的变异

本文研究了广西人工林马尾松木材性质的变异及幼龄材与成熟材的差异。结果表明 ,幼龄材与成熟材的分界年龄在 14　 16a ,解剖性质在径向上的变异规律为 :射线比量、树脂道比量、胞壁率、胞腔直径、胞壁厚、管胞长度、管胞宽度和晚材壁腔比是自髓心向外呈递增趋势 ,管胞比量和晚材率为递减趋势 ,早材壁腔比和早材腔径比则近似于一条直线。方差分析结果表明 :树脂道比量、胞壁率、胞壁厚、管胞长度和管胞宽度 ,幼龄材与成熟材差异达显著或极显著水平。 5项木材物理力学性质均为成熟材高于幼龄材 ,且均达差异显著水平。木材性质间的相关分析表明 :木材基本密度与管胞长度、管胞宽度、射线比量、树脂道比量、胞壁率呈显著的正相关关系 ,木材气干密度与抗弯强度、抗弯弹性模量、顺纹抗压强度也呈显著的正相关关系     

中山杉和落羽杉木材解剖性质研究

以12年生中山杉和落羽杉胸高处木材为研究对象,利用纤维测定仪测定其管胞长度、宽度,采用图像分析仪测定其管胞壁厚、壁腔比和各种组织比量,利用双因素方差分析方法分析树种因素、距髓心生长轮数对管胞形态和组织比量等特征的影响.中山杉木材的管胞长度、宽度、长宽比均值分别为2 737.84μm、44.84 μm和60.86,落羽杉木材的管胞长度、宽度、长宽比的均值分别为2 698.52 μm、43.44μm和61.51;中山杉木材的早材和晚材管胞弦向壁厚均值分别为5.91 μm和7.57 μm,落羽杉木材的早材和晚材管胞弦向壁厚均值分别为5.89 μm和6.54 μm;中山杉早材和晚材管胞壁腔比均值分别为0.15和0.35,落羽杉的早材和晚材壁腔比均值与中山杉的一致.双因素方差分析的结果表明:除了中山杉晚材的管胞壁厚显著大于落羽杉晚材的管胞壁厚之外,这两个树种其它管胞形态特征、各种组织比量的差异在0.05水平不显著,该结果表明这两种木材的解剖特征很接近;中山杉、落羽杉幼龄木材除了管胞旱材的壁腔比、薄壁细胞组织比量在不同生长轮之间的差异在0.05水平不显著之外,测试的其它特征在不同生长轮之间的差异在0.05水平具有显著性.中山杉、落羽杉木材的解剖特征的径向变异具有相同的规律:管胞长度、管胞宽度、弦向壁厚、管胞组织比量从髓心向树皮都有逐渐增加的趋势,而射线组织比量从髓心向树皮有逐渐降低的趋势,薄壁细胞比量较小,径向变异也较小、没有明显的规律.     

幼龄材范围的确定及树木生长速率对幼龄材生长量的影响

本文以杉木、日本落叶松的人上林和天然林木材为对象，选择ｙ＝ａ＋ｂｌｎｘ回归模式。利用其管胞特征因子随年轮数的变化，研究划分幼龄材年轮界限的最适因子，并就生长速率对幼龄材生长量的影响进入了探讨。结果表明：杉木和日本落叶松的人工林及天然林木的管胞特征值在径向水平上的变化均遵循ｙ＝ａ＋ｂｌｎｘ模式，尤其管胞长度与年轮数回归的相关系数Ｒ均达０．９８以上；管胞长度与管胞宽度及纤丝用相比，遗传率最大，随年轮数变化的模式最稳定，是划分幼龄材界限的最佳因子，由此得出杉木人工林幼龄材界限年轮为２０－２２（距髓心距离为１２．９－１３．２ｃｍ）、天然林为１６－１８（４．１－４．５ｃｍ），日本落叶松人工林为１９－２３（８．７－１０．５ｃｍ）、天然林为２３－２４（２．９－３．１ｃｍ）；幼龄材生长量与树木生长速率成正比。     

火炬松半同胞家系遗传测定与早期性状评定

对15年生火炬松半同胞家系的生长和材性性状测定表明:火炬松家系树高、胸径、材积、木材基本密度、纤维素含量、管胞长度与宽度等具有显著的差异;在家系水平上,木材基本密度、纤维素含量、管胞长度与宽度和材积生长相关不明显．遗传力测定表明:家系生长性状与材性性状平均遗传力均较高,达到中等程度以上．对树高生长、胸径生长、木材基本密度、纤维素含量、管胞长度与宽度等性状进行年度相关、早晚期选择研究表明:火炬松家系的生长相关主要由遗传决定;树高从第5年开始,胸径从第4年开始与以后各年的相关系效均在0．7以上,表明以此为最低年龄进行早期选择有较大的可靠性;木材基本密度10年生与其后各年龄级的相关系数值趋于稳定,术材密度最低选择年龄为10年;木材纤维素含量11年生与其后各年龄级的相关系效值趋于稳定,木材纤维素含量的最低选择年龄为11年．     

不同营养元素的施肥处理对马尾松近熟林木材基本性质的影响

研究了 4种不同营养元素的施肥处理对马尾松近熟林木材基本性质的影响。结果表明 ,在不同施肥处理后的同一年中 ,N、P、K、NPK施肥处理对木材管胞长、宽及基本密度的影响不同 ,同一施肥处理在不同年度中 ,对上述性质的影响亦异 ,总之 ,无明显变化规律。方差分析表明 4个施肥处理与无施肥处理的管胞长、宽及基本密度差异均不显著 ,生长轮宽度与管胞形态和基本密度都不显著相关。     

Variation in density of Picea sitchensis in relation to within-tree trends in tracheid diameter and wall thickness

The influences of cambial age and ring width on density of Sitkaspruce (Picea sitchensis (Bong.) Carr) were analysed in relationto within-tree trends in tracheid diameter and cell wall thickness.Discs were sampled at breast height from a total of 24 trees,from seven stands at three contrasting sites in Wales, and atbreast height, 30 per cent and 60 per cent total tree heightfrom one of the stands. Across the juvenile wood, ring density decreased with ring numberfrom the pith while radial tracheid diameter increased. Theseoverall trends were considered to be inherent to tree growth,presumably associated with cambial ageing, since they occurredin all trees on all sites. In juvenile wood, density also variedwith site growth rate (as indicated by ring width) at similarcambial age, wider rings being associated with more rapidrateof change in tracheid diameter with ring number and with decreasein tracheid wall thickness. Consequently, on a site having treeswith high growth rate density decreased more rapidly acrossthe juvenile wood, down to a lower minimum value, than on siteswith a slower growth rate. In mature wood, the decrease in densitywith increase in ring width was associated with differencesin both tracheid diameter and wall thickness. Density was slightly(though not significantly) higher at breast height than in comparablerings at 30 per cent total height, associated with significantlythicker tracheid walls at breast height. Changes in radial tracheid diameter (with ring number, or withring width) were associated with greater differences in theearlywood than towards the latewood end of each growth ring,while variations in wall thickness with ring width were associatedwith rate of increase in wall thickness towards the latewoodend. This may account for some previously conflicting reportson influence of silvicultural management on density, for densityis likely to vary with influence of environment on the seasonalcycle of cambial activity. The extent of the juvenile wood as delimited by the inner coreof wide growth rings does not necessarily correspond to theregion of varying tracheid dimensions in Sitka spruce.     

火炬松不同种源纸浆材材性的变异

1983年火炬松31个种源引种栽培在浙江富阳中国林业科学研究院亚热带林业研究所实验林场,研究表明该批种源间10年生树木生长量和纸浆材材性因子如晚材率、管胞形态特征值(管胞长度、宽度、腔径、壁厚、长宽比、腔径比、壁腔比)、管胞S2层微纤丝角和木材基本密度存在着显著差异,木材主要化学成分中纤维素和木素含量种源间存在着显著差异,而戊聚糖和苯醇浸提物含量种源间差异不显著.这些材性特征除了木材化学性状因子外,均受中等以上程度遗传控制.木材纤维素、木素、戊聚糖和苯醇浸提物含量的广义遗传力分别为0.088、0.003、0.340和0.307,其余性状广义遗传力均大于0.50.引种地栽培环境对木材性状有显著影响.种源原产地纬度与树木生长量、管胞宽度、管胞直径和管胞微纤丝角呈负相关,与晚材率、木材密度呈正相关.31个种源树木胸高直径与管胞长宽比、管胞壁腔比、木材密度呈显著负相关,与管胞宽度、管胞直径、管胞腔径比呈正相关.     

Variation pattern of wood properties of naturalCunninghamia lanceolata

In this paper, the variation pattern of wood properties was studied for naturalCunninghamia lanceolata. The mathematical models of property parameters were obtained on tracheid length, microfibril angle, late wood percentage, growth ring width and growth ring density in the radial direction. The interrelation were analyzed between tracheid length and microfibril angle. The result can provide scientific theory basis for wood utilization and early prediction of wood properties.     

Basic density,longitudinal shrinkage and tracheid length of juvenile wood of Picea abies (L.) Karst

Variation in the growth ring width, basic density, longitudinal shrinkage and tracheid length was investigated in the juvenile wood of Norway spruce samples taken from different heights in the stem. Annual height increments were cut from the ten youngest shoots from trees of three different heights. By this method the properties of an individual growth ring could be analysed without taking samples from each ring. Sixteen tree tops of an average stem height of 8, 15 and 25 m were analysed. Basic density was low in the first shoot, highest in the second or third one and decreased gradually thereafter. Longitudinal shrinkage was highest close to the pith and decreased to about 0.2% in the outer rings. Tracheids were only ca. 1 mm long close to the pith and their length increased sharply towards the tenth shoot. The properties of juvenile wood varied with the height in the stem. Longitudinal shrinkage around the pith seemed to increase with increasing height and basic density was highest at 25 m stem height. The applicability of the method for the calculation of basic density and tracheid length in individual growth rings close to the pith is discussed.     

Geographic variation and genetic performance of Picea koraiensis in growth and wood characteristics

Eight provenances of 19-year-oldPicea koraiensis Nakai from the provenance trials of Maoershan (45°20′N, 127°30′E), Liangshui (47°10′N, 128°53′E) and Jiagedaqi (50°24′N, 124°07′E) in Northeast China were investigated to analyze the genetic variation in growth characteristics (tree height and diameter) and wood characteristics (tracheid length, tracheid diameter, tracheid wall thickness, annual ring width as well as wood density). Great variation in height growth and breast height diameter growth was observed among the provenances, and along with the increase of tree age, these provenances presented different geographic adaptability. The growth characteristics ofPicea koraiensis stand at age of 10 in Maoershan and Liangshui provenance trials had a positive correlation with longitude, and with increase of tree age to 15 and 19, the tree growth of the provenances displayed a significant positive correlation with latitude as well as altitude. For wood characteristics, great variation was also found among the provenances. There exists a close relation between growth characteristics and wood properties of the provenance. The height and breast height diameter growth of the provenance had a positive correlation with tracheid diameter and annual ring width, and a negative correlation with tracheid wall thickness and wood density. Genetic performance of the provenance in all above characteristics was also investigated in order to provide more useful information for comprehensive selection of this species for pulpwood and plywood production. Foundation item: The paper was supported by National Key Project of The State Forestry Administration. (96-011-01-06) Biography: WANG Qiu-yu (1957-), female, professor in College of Life Sciences, Northeast Forestry University, Harbin 150040, P. R. China. Responsible editor: Song Funan     

VARIATION PATTERN OF WOOD PROPERTIES OF NATURALCUNNINGHAMIA LANCEOLATA

m0DUCYIONCunninghaniahaceolataisoneofmalnusedwoodspeciesinSouthernChina.ItPOs-sessesthecharactenshcsofhighadaPabilityandwideuhlity.WoodscienhstshavedonemorereaearchingworkonthegrOwingcharac-tenshcsandwoodPhysicalPropeniesofPlantedCunninghamiaboceolata,butlessonthewoodPropeniesvanahonpatternofnatUralCunninghtzmiahaceolata.ThewoodpropeniesandtheircorrelahonofCunn~oriahaceolatainnatUralforestwerestudiedinordertoProviderelevamtech-mqueparametersofitsPeffochonanduhliza-tion.nsThunSAunare…