Physicochemical and ecotoxicological evaluation of estuarine water quality during a dredging operation

Purpose

Most of the information concerning the effects of contaminated sediments on estuarine organisms deals with the impacts of bed forming sediments. The ecotoxicological potential at the time of a dredging operation is more difficult to assess, and few studies have dealt specifically with resuspended contaminated sediments. The aim of this study was to determine whether release of contaminants through sediment resuspension during a dredging operation in the Itajaí-açu estuary (Brazil) changed the water quality classification and had an ecotoxicological impact on the near-field water column during the critical moment of this operation.

Materials and methods

Waters from two sites (control and dredged sites) were analyzed for physicochemical parameters before, during, and after a dredging operation. In parallel, a short-term, sensitive battery of biotests (bacteria, algae, and daphnids) was performed with water samples before and during this operation according to the ISO bioassay protocols.

Results and discussion

No short-term toxicity was observed with waters collected before or during the dredging operation. The results showed that desorption of contaminants from suspended particles of sediments with a low level of contamination during a dredging operation lowered the water quality in the near-field water column but that this did not promote significant acute toxicity effects on the organisms tested.

Conclusions

More detailed studies are needed (e.g., the question of the reliability of biotests under turbulent, particle-rich conditions) to fully understand this complex issue regarding water column ecotoxicity during the whole dredging operation and to support decisions on the management of dredging activities.

     

Effects of biofilm on turbulence characteristics and the transport of fine sediment

Purpose

Biofilm growth changes the sediment properties and the characteristics of the bed, which further influences the interactions between the flow and the sediment bed, such as the turbulence characteristics of the flow and the erosion response of the sediment to hydrodynamic forces. In this study, the effects of biofilm on the turbulence characteristics of the flow and bio-sediment suspension are investigated.

Materials and methods

Cohesive sediments were collected from the bottom of the Three Gorges Reservoir, which have a median size of less than 0.1 mm. Flume experiments were conducted for the erosion of the sediment bed with and without biofilm under the same flow rate. Acoustic Doppler Velocimetry (ADV) was used to measure the velocities along the depth, based on which the distribution of Reynolds shear stress, time-average velocity, turbulence intensities, turbulence kinetic energy flux and budgets, and bursting events of the flow were determined. Meanwhile, the biofilm effects on the physical characteristics of sediments, such as the diameter, density, and falling velocity, were summarized from previous studies. Then, the changes of the vertical distribution of suspended sediment concentration and the near-bed concentration were evaluated.

Results and discussion

After biofilm growth, the time-averaged velocity increases by approximately 6.7% under the low flow rate condition with a flat bed, and by more than 20% under the high flow rate condition with a deformed bed. The vertical distribution of the turbulence intensity becomes more uniform under the high flow rate condition. However, the changes of the turbulence kinetic energy flux and budgets due to biofilm are hardly observed by the scattered measurement data, and more experiments need to be conducted in the future.

Conclusions

Biofilm exerts an influence on the turbulence characteristics, mostly by affecting the deformation extent of the sediment bed. Meanwhile, the changes of the physical properties of sediments due to biofilm significantly influence the transport of suspended sediment.

     

Fine-sediment dynamics: towards an improved understanding of sediment erosion and transport

Purpose

Using Ells River, Alberta, Canada bed sediments, this study aims to determine (1) the erosion, transport, and deposition characteristics of cohesive bottom sediments, and (2) the influence of the microbial community in this regard.

Materials and methods

A 2-m annular flume was used to generate bed shear to assess cohesive sediment dynamics for eroded beds with consolidation/biostabilization periods of 1, 3, and 7 days. Additional optical particle sizing, image analysis, densitometry, and microbial analysis were employed to further the analysis with respect to bed erosion and eroded floc characteristics.

Results and discussion

Sediment dynamics can influence the benthic and planktonic community health within aquatic systems. The critical bed shear stress for erosion increased from 0.05 to 0.19 Pa (for 1- to 7-day runs). Consolidation (dry density) increased with time and depth and eroded biofilm biomass was observed to increase with time. The community structure of the eroded sediment did not change with time suggesting a stable well-established and highly selected community. Hydrocarbon-degrading bacteria were present within the microbial consortium. The sediment was highly hydrophobic (96 %) due to a high natural oil content which likely had a profound effect on sediment dynamics, flocculation, and sediment cohesion. Eroded sediment settled poorly, which will result in the long-range transport of associated contaminants.

Conclusions

The Ells River possesses some unique properties which should be considered when assessing contaminant source, fate, and effect. The most significant of these are small floc size, the hydrophobicity of the sediment, and the biological community as these were found to be influential in both the erosion and flocculation processes. It is important that any management strategies and operational assessments of reclamation strategies that may have implication on river health incorporate the sediment compartments (SS and bed sediment), biology, and the energy dynamics within the system in order to better predict the downstream flux of sediments.

     

Modeling of hydrophobic cohesive sediment transport in the Ells River Alberta,Canada

Purpose

In this paper, a novel modeling approach is applied to assess the unique transport characteristics of hydrophobic (bitumen containing) cohesive sediment for the Ells River, AB, Canada. The modeling offers a new way of treating the transport and fate of fine sediment in rivers and points to the importance of including a sediment entrapment process in the modeling of the Ells River sediment dynamics.

Materials and methods

The modeling approach involves combining two existing models (RIVFLOC and MOBED). Using fine sediment transport parameters derived from laboratory flume experiments (e.g., settling velocity of sediment as a function of floc size and the critical shear stresses for deposition) and the calculated flow field from the MOBED model (using field survey data such as, cross-sectional geometry, river slope, grain size of bed material, and discharge), the RIVFLOC model is used to predict the transport characteristics (including entrapment) of the hydrophobic Ells River sediment.

Results and discussion

The application of the connected RIVFLOC and MOBED models, demonstrated the unique hydrophobic sediment dynamics of the Ells River. The model showed no deposition (in the classical sense) of the hydrophobic sediment as the bed shear stresses, even at base flow, are well above the critical bed shear for deposition (flocculation is shown to occur, but its impact on settling is negligible given the high shear stresses). However, the model showed the possibility of fine sediment ingression into the river bed (interstitial voids) due to the entrapment process which is known to occur at bed shear stresses well above the critical shear stress for deposition.

Conclusions

The salient features of RIVFLOC and MOBED models and their applications for understanding the transport and fate of unique hydrophobic fine sediments are presented. The models are shown to be useful for the understanding and projection of flow characteristics and sediment dynamics (including entrapment), and will be of benefit for the adaptive management of riverine monitoring programs given various flow scenarios including extreme events and climate change.

     

Erodibility and transport behavior of dreissenid mussel deposits in an annular flume

Purpose

Zebra mussels (Dreissena polymorpha) alter the transport dynamics and fate of particulate matter in aquatic systems by intercepting, retaining, and recycling suspended materials. This study examines the effect of particle processing by dressenids on the nature (grain size distribution, settling velocity, porosity  and density) and transport properties (critical shear stress for erosion, erosion rates, and bed stability) of suspended particulate matter in lakes.

Materials and methods

The bed stability, erosion rate, and critical shear stress for erosion of dreissenid biodeposits were measured in an annular flume. The particle size distribution, settling rate, density, and porosity were measured to characterize the physical nature of the biodeposits. Materials studied in the flume include (1) a combination of biodeposits and surface sediments collected from dreissenid beds and (2) biodeposits harvested in a weir box populated with dreissenids.

Results and discussion

The settling rates of both biodeposit/sediment mixtures and pure biodeposits were lower than natural sediment in lacustrine environments. Erosion characteristics and transport properties of biodeposits were strongly influenced by bed age and the presence of mussels. Bed stability increased after 7 days, with a τ_crit of 0.26 Pa compared to the 2- and 14-day consolidation periods (τ_crit?=?0.13 and 0.15 Pa), respectively. The observed changes in bed stability with bed age will modify the transfer of particulate materials to the offshore profundal zone as well as the rates and magnitudes of sediment-associated nutrients in the near shore zone.

Conclusions

Biostabilization of surficial lake-bottom sediments impacted by mussel biodeposits may increase bed stability and reduce the export of particulate matter to the offshore environment. Further, well-developed communities of dreissedid mussels have an armoring effect on deposited sediment, which reduces remobilization of sediment and biodeposits. However, once eroded, the dreissedid modified deposits will likely be transported further due to their low-settling velocity.

     

Long-term modelling of reservoir sedimentation with turbid underflows

Purpose

This paper presents the development of a turbid density current module (TDCM) for a one-dimensional quasi-steady reservoir sedimentation model suitable for long-term simulations and an example of its application.

Materials and methods

The module determines the plunging point of a density current based on the criterion of the densimetric Froude number. Following plunging, simulation continues in a supercritical regime as long as the energy of density flow and bed slope are sufficient to support transport in this mode, or until the dam is reached. A muddy pond is then formed. An adapted version of the theory of Toniolo et al. (2007) is used to compute water and sediment balance in a muddy pond. If the level of muddy pond exceeds the lowest level outlet, sediment is vented from the reservoir.

Results and discussion

The model was applied to one of the largest reservoirs in the world, the Nurek reservoir in Tajikistan. Historical data on bed levels and sediment inflow as well as a recent survey from 2015 were used to calibrate and validate the model. The model showed good results both in terms of modelled bed levels and composition of deposited sediment. For comparison purpose, the model was also calibrated without the TDCM module. However, the discrepancy between the observed and modelled data was significantly higher, confirming that the good match in the case of the TDCM module was not achieved solely by calibration, but rather by a more appropriate approach to modelling.

Conclusions

These results support the choice of using the model with TDCM for modelling a general pattern of long-term deposition in the Nurek reservoir, in which turbid density currents play an important role.

     

Bathymetric modeling of sediments and organic carbon of polluted rivers in southeastern China

Purpose

Rivers in low plains in the subtropical regions of China, where the population is dense and economies are active and well-developed, might be a large terrestrial carbon pool. This present study of the Sanyang wetlands in Wenzhou, southeastern China, aims to quantitatively estimate the volume of sediments in this region’s polluted river systems and their carbon storage.

Materials and methods

The bathymetry of river sections were surveyed using an echo sounder equipped with a differential GPS. An underwater digital elevation model (DEM) was then developed using the anisotropic ordinary Kriging method. Sediment samples were collected and analyzed for carbon content and sediment properties. Carbon storage in sediments was calculated using bathymetric and sediment analysis data.

Results and discussion

The studied rivers have been receiving organic pollutants from local residences and industries for decades. Results from a river network of 1.2 km² revealed a total carbon storage of 46.7 million kg in the sediments which had a volume of 1.4 million m³, with the upper 20 cm depth of sediments contributing about one third of this carbon storage.

Conclusions

The present work demonstrated that GIS technologies can be used to create digital river sediment surfaces and assess sediment amounts as well as determine the spatial distribution of sediments and their components. This could provide further insight into river restoration planning and other options from a carbon-balance perspective.

     

Assessment of potentially toxic element contamination in soils from Portman Bay (SE,Spain)

Purpose

The present study deals with the geochemical fractions of Pb, Cd, Zn, Cu and As present on profiles using chemical simple extraction process. This work was conducted on Portman Bay, located in the SE Spain and strongly affected by mining activities.

Materials and methods

Four simple extractions were applied to selected samples in order to evaluate the potential mobility of metals. X-ray diffraction (XRD) was applied to the characterisation of samples and the residues remaining after each extraction, providing additional information about the sediment phases carrying the elements studied.

Results and discussion

The results obtained after the extractions suggested that the highest potentially toxic element (PTE) content was obtained in the oxidising medium. The mineralogical composition is an important factor that should be taken into account in the evaluation of PTE mobility, firstly because the mineral phases react differently in the proposed situations depending on their chemical nature, and secondly, because the presence of a particular phase depends on the degree of weathering.

Conclusions

The evaluation of PTE mobility and mineralogical composition under different environmental conditions may be very important in the execution of restoration projects which could involve dredging and mobilisation of materials.

     

Biochar improves sediment microbial fuel cell performance in low conductivity freshwater sediment

Purpose

The low conductivity of sediments for mass and electron transport is the most severe limiting factor in sediment microbial fuel cells (SMFCs), so that sediment ameliorations yielded more remarkable effects than electrode improvements. The objective of this research was to enhance the electricity generation of SMFCs with amendments of biochar to freshwater sediments for conductivity enhancement.

Materials and methods

Laboratory-scale SMFCs were constructed and biochars were produced from coconut shells at different temperatures. Variations in the power output, electrode potential, internal resistance, total organic carbon (TOC) content, and microbial communities were measured.

Results and discussion

Amending with biochar reduced the charge transfer resistances of SMFCs and enriched the Firmicutes (mainly Fusibacter sp.) in the sediment, which improved the SMFC power generation by two- to tenfold and enhanced the TOC removal rate by 1.7- to fourfold relative to those without the amendment.

Conclusions

The results suggested that biochar amendment is a promising strategy to enhance SMFC power production, and the electrical conductivity of biochar should be considered important when interpreting the impact biochar has on the electrical performance of soil or freshwater sediment MFCs.

     

Incipient motion for gravel particles in clay-silt-gravel cohesive mixtures

Purpose

Incipient motion plays an instrumental role in understanding various aspects of sediment transport, such as river bed aggradation and degradation, channel design, bank erosion, scour around bridge piers, and water quality issues.

Materials and methods

Experiments were conducted to study the incipient motion of gravel particles in three types of bed material, i.e., gravels only, silt-gravel mixture, and clay-silt-gravel mixture. The clay content varied from 10 to 50% in the clay-silt-gravel mixture while silt and gravel were in equal proportion by weight. Samples were taken out from the prepared cohesive bed for the determination of their bulk density, unconfined compressive strength, and water content. The incipient motion was observed visually, which corresponded to the beginning of movement of gravel particles in the mixture. The shear stress corresponding to incipient motion was computed using measured flow depth and slope of water surface. The physical appearance of the top layer of cohesive bed was observed visually at the end of experiment.

Results and discussion

The effects of clay content, water content, unconfined compressive strength, and bulk density of the mixture on the critical shear stress were investigated using the data collected in this study on clay-silt-gravel mixture along with the data from previous studies. A relationship is proposed for the computation of critical shear stress of gravel particles in the cohesive mixtures. The physical appearance of the top surface of the bed for clay-silt-gravel mixture has also been investigated with varying percentages of clay content in the mixture.

Conclusions

High clay percentage significantly increased the critical shear stress. The presence of silt lowers the critical shear stress especially when there is low clay content (up to 20%) in the mixture. The clay content along with the bulk density was found to be the dominant parameters that affect the incipient motion of the gravel particles in the cohesive mixtures. The proposed relationship for critical shear stress was found to be in good agreement with the observed ones.

     

Effect of hydrodynamics factors on sediment flocculation processes in estuaries

Purpose

Cohesive sediment is able to flocculate and create flocs, which are larger than individual particles and less dense. The phenomenon of flocculation has an important role in sediment transport processes such as settling, deposition and erosion. In this study, laboratory experiments were performed to investigate the effect of key hydrodynamic parameters such as suspended sediment concentration and salinity on floc size and settling velocity. Results were compared with previous laboratory and field studies at different estuaries.

Materials and methods

Experimental tests were conducted in a 1-L glass beaker of 11-cm diameter using suspended sediment samples from the Severn Estuary. A particle image velocimetry system and image processing routine were used to measure the floc size distribution and settling velocity.

Results and discussion

The settling velocity was found to range from 0.2 to 1.2 mm s^?1. Settling velocity changed in the case of increasing suspended sediment concentration and was controlled by the salinity. The faster settling velocity occurred when sediment concentration is higher or the salinity is lower than 2.5. On the other hand, at salinities higher than 20, in addition to increasing SSC, it was found that the situation was reversed, i.e. the lower the sediment concentration, the faster the settling velocity.

Conclusions

Sediment flocculation is enhanced with increasing sediment concentration but not with increasing salinity.

     

Sediment transport below a small alpine reservoir desilted by controlled flushing: field assessment and one-dimensional numerical simulation

Purpose

Sediment transport and riverbed sedimentation were investigated in an alpine stream below a small hydropower reservoir desilted by a controlled sediment flushing (CSF) operation. The term “controlled” refers to the operational tasks implemented to mitigate the downstream environmental impact of the operation. The experimental dataset acquired before, during, and after the CSF was also used to carry out and calibrate a one-dimensional sediment transport model of the monitored event.

Materials and methods

The investigated reservoir is located in the central Italian Alps, and its original storage was 160,000 m³, about 30% filled by a mixture of sand and silt/clay before the CSF. Downstream sediment concentration was controlled by releasing clear water from upstream reservoirs and regulating the work of earth-moving equipment in the emptied reservoir. A 3.6-km-long reach with average slope of 0.015 was monitored: concentration and grain size of suspended sediment were measured during the CSF and the riverbed alteration was evaluated by volumetric sampling and measurements of the deposits’ thickness. Sedimentation and River Hydraulics—One Dimensional (SRH-1D) was used to simulate sediment transport during the monitored CSF. Model parameters were calibrated by comparing the computed and the observed amount of sediment deposited along the study reach.

Results and discussion

Sediment flushing was carried out in October 2010 for 3 days. Ca. 16,000 m³ of sediment were evacuated, representing approximately 30% silt/clay and 70% sand. 2.4 Mm³ of clear water was released to reduce sediment concentration and increase transport capacity downstream. About 3000 m³ of sand was deposited in the study reach after the CSF, with maximum height up to 0.2 m. Although the riverbed before the CSF was simply set as mono-granular, after calibrating the parameters, good agreement was achieved between the depositional pattern computed by SRH-1D and the one observed, both in terms of deposit thickness and grain size of deposited sediment. The sensitivity analysis revealed a major role of the parameters controlling bed mixing processes in affecting the simulated deposition after the CSF.

Conclusions

Sediment below 0.1 mm in diameter was not detected in river deposits after the flushing: the effects on river biota associated with substrate clogging by very fine sediment were therefore minimized. After proper calibration, 1-D sediment transport modeling can effectively support the planning of CSF operations: to minimize the downstream environmental effects, concurrently achieving acceptable flushing efficiency, the analyzed scenarios as well as the model outputs need to be carefully evaluated from a multidisciplinary perspective.

     

Assessment of cytotoxicity and AhR-mediated toxicity of sediments from water level fluctuation zone in the Three Gorges Reservoir,China

Purpose

The Three Gorges Dam project is one of the biggest projects in the world. The water level fluctuation zone (WLFZ) was created with impoundment. The purpose of the current study is to investigate the ecotoxicological potential of the sediment extracts from the WLFZ and propose future WLFZ monitoring for early detection of environmental changes brought about by pollution.

Materials and methods

The investigation was performed by using cell-based in vitro bioassays to determine acute cytotoxicity (neutral red retention assay) and mechanism-specific aryl hydrocarbon receptor (AhR)-mediated activity (7-ethoxyresorufin-O-deethylase (EROD) induction assay) of sediment extracts with rainbow trout (Oncorhynchus mykiss) liver cells (RTL-W1).

Results and discussion

Results showed that the cytotoxicity and AhR-mediated toxicity potential of the sediment extracts from the WLFZ in the Three Gorges Reservoir (TGR) were moderate of level compared with the ecotoxicity of sediments from other river systems. However, according to a sediment classification system in Germany, sediments from some individual sites in the WLFZ showed strong toxicity. Compared to the results from the Yangtze River in our previous study, more attention should be paid to the aryl hydrocarbon receptor inducers in the WLFZ in TGR.

Conclusions

The in vitro bioassays used in this study may serve as a valuable tool to predict the potential ecological hazards of the organic pollutants in the WLFZ to the aquatic organisms in some extent.

     

Size characteristics of sediments eroded from three soils in China under natural rainfall

Purpose

The particle-size distribution of runoff sediment is important in understanding, characterizing and modeling the transport behavior of sediment and sediment-associated chemicals. The objective of this study was to investigate the particle-size distribution of sediments eroded from three soils in China under natural rainfall.

Materials and methods

Each of the three soils was packed to a depth of 30 cm in a 20?×?2.1 m runoff plot. Sediments yielded in nine natural rainfall events were analyzed for their particle-size distribution prior to and following dispersion.

Results and discussion

The sediment size measured in the undispersed condition was always larger than the one determined after chemical dispersion, indicating that part of the sediment was eroded in aggregated form. The degree of sediment aggregation depended on the clay content and the organic matter content of the sources. The mean sediment size quantified by mean weight diameter linearly increased with sediment yield for the two soils with relatively high clay content. The rate of increase was greater in the undispersed condition than that in the dispersed condition for these two soils. Comparing sediments to the corresponding source soil, the results of mean weight diameter and enrichment ratio both revealed that aggregate-size distribution was more sensitive to soil erosion than the primary particle-size distribution. Small aggregates, rather than the primary particles, were selectively eroded in the rainfall events.

Conclusions

These findings support the use of both dispersed and undispersed sediment-size distributions for the characterization of sediment transport and the associated sediment-bound nutrients and contaminants.

     

Impacts of sea-level rise on sediment microbial community structure and function in two New England salt marshes,USA

Purpose

There is growing evidence for a tight linkage between the structure and function of microbial communities and for the importance of this relationship in ecosystem responses to disturbances such as sea-level rise (SLR). While the role of plants in determining the capacity of salt marshes to keep pace with SLR through sediment accretion has received considerable attention, the role of microbes in offsetting these gains via decomposition is less understood.

Materials and methods

We conducted a controlled experiment to determine the structural and functional responses of microbes to SLR, using soil from the low intertidal zone of two New England salt marshes in Massachusetts and New Hampshire, USA. We used terminal restriction fragment length polymorphisms (t-RFLPs) generated from microbial 16S rDNA to evaluate community composition and diversity and focused on changes in respiration with SLR, measured as total respired carbon normalized by percent organic matter, as a surrogate for decomposition rate.

Results and discussion

We observed a 24% reduction in microbial respiration with a simulated rise in sea level of 40 cm. This functional change was accompanied by a structural shift in microbial community composition among samples from New Hampshire but not Massachusetts, assessed via principal coordinate analysis of t-RFLP data. We also found greater microbial diversity within our New Hampshire samples, suggesting that low diversity may constrain community compositional shifts.

Conclusions

Our results suggest that decreased microbial respiration could alleviate the negative effects of SLR on salt marsh surface elevation, at least in the short term, and that the diversity of the soil microbial community may positively influence functional responses such as respiration.

     

Planktonic algal bloom significantly alters sediment bacterial community structure

Purpose

We determined the relationship of a planktonic algal bloom with spatial and temporal changes in sediment bacterial communities in a eutrophic urban river in the Taihu Basin, China.

Materials and methods

Surface sediments from different locations on the river, including with and without an algal bloom, were collected monthly for 1 year. Sediment bacterial communities were assessed by sequencing 16S rRNA gene amplicons using an Illumina MiSeq.

Results and discussion

There were distinct spatial and temporal changes in sediment bacterial community structure. Significant decrease in the Shannon diversity corresponded with the peak chlorophyll a (Chl a) concentration. Proteobacteria, Chloroflexi, and Bacteroidetes were the dominant phyla throughout the year; however, their relative abundances changed seasonally. At the time of peak Chl a concentrations, Proteobacteria and Bacteroidetes comprised a greater proportion of the bacterial community. Bacterial community structure also varied spatially at the operational taxonomic unit (OTU) level according to canonical correspondence analysis (CCA), especially in locations with an algal bloom compared with those without an algal bloom. There were positive correlations between multiple bacterial genera and Chl a content, suggesting the potential for facilitative relationships between phytoplankton and bacteria. Based on the CCA, water temperature, NH₄ ⁺-N, TN, NO₃ ^?-N, and TP in the sediment and Chl a contents in the water column were significantly correlated with sediment bacterial community structure (P < 0.05).

Conclusions

Planktonic algal blooms may influence sediment bacterial community structure at all taxonomic levels in urban rivers. This work emphasizes the need for more comprehensive studies regarding the impact of planktonic algal blooms on sediment bacterial communities.

     

Speciation and potential long-term behaviour of chromium in urban sediment particulates

Purpose

Chromium, a potentially harmful element, occurs commonly within the urban sediment cascade as a result of abundant industrial and transport-related sources. The risks that Cr-bearing particles pose to ecosystems and humans depend on the solid-phase chemical speciation of Cr and its environmental mobility. In this study, we adopt an integrated geochemical approach to investigate and determine the long-term fate of Cr in the urban sediment cascade.

Materials and methods

We use bulk chemical digests, sequential chemical extraction analysis, electron microscopy, electron microprobe and microfocus XANES analysis to describe the solid-phase speciation, geochemical characteristics and potential long-term behaviour of Cr in urban particulate matter from both aquatic sediment and road dust sediment (RDS) in Manchester, UK.

Results and discussion

Cr-bearing grains within RDS and aquatic sediment are predominantly iron oxides and alumino-silicate glass grains. Electron microprobe analysis indicates Cr concentrations up to 3300 and 133,400 μg g^?1 in the RDS and aquatic grains, respectively. XANES analysis indicates that Cr(III) is the dominant oxidation state, with only trace amounts of Cr(VI). Importantly, Cr speciation does not appear to have changed between sedimentary environments and the dominance of Cr(III) suggests limited bioavailability or toxicity under predominant environmental (anoxic and neutral pH) conditions in the aquatic sediment sink. Furthermore, geochemical analyses suggest the environmental mobility of Cr in the aquatic sediment sink is low (compared to other toxic metals) due to its association mainly with alumino-silicate glass grains and its inclusion as an integral part of the glass structure.

Conclusions

Industrial glass grains are a major component of urban sediment worldwide. The speciation and geochemical investigations performed in this study suggest most Cr within the urban sediment cascade may be resistant to environmental processes that could mobilise other toxic metals.

     

Factors controlling sediment trapping in two freshwater tidal wetlands in the Biesbosch area,The Netherlands

Purpose

A thorough understanding of mechanisms controlling sedimentation and erosion is vital for a proper assessment of the effectiveness of delta restoration. Only few field-based studies have been undertaken in freshwater tidal wetlands. Furthermore, studies that measured sediment deposition in newly created wetlands are also sparse. This paper aims to identify the factors controlling the sediment trapping of two newly created freshwater tidal wetlands.

Materials and methods

Two recently re-opened polder areas in the Biesbosch, The Netherlands are used as study area. Field measurements of water levels, flow velocities, and turbidity at both the in- and outlet of the areas were carried out to determine the sediment budgets and trapping efficiencies under varying conditions of river discharge, tide, and wind in the period 2014–2016.

Results and discussion

Short-term sediment fluxes of the two study areas varied due to river discharge, tide, and wind. A positive sediment budget and trapping efficiency was found for the first study area, which has a continuing supply of river water and sediment. Sediment was lost from the second study area which lies further from the river and had a lower sediment supply. The daily sediment budget is positively related to upstream river discharge, and in general, export takes place during ebb and import during flood. However, strong wind events overrule this pattern, and trapping efficiencies decrease for increasing wind strengths at mid-range river discharges and for the highest river discharges due to increased shear stress.

Conclusions

Delta restoration, based on sedimentation to compensate for sea-level rise and soil subsidence, could only be effective when there is a sufficient supply of water and sediment. Management to enhance the trapping efficiency of the incoming sediment should focus on directing sufficient river flow into the wetland, ensuring the supply of water and sediment within the system during a tidal cycle, creating sufficiently large residence time of water within the polder areas for sediment settling, and decreasing wave shear stress by the establishment of vegetation or topographic irregularities.