首页 | 本学科首页   官方微博 | 高级检索  
     

刀具磨损声发射信号的混沌特性分析
引用本文:关 山,彭 昶. 刀具磨损声发射信号的混沌特性分析[J]. 农业工程学报, 2015, 31(11): 60-65
作者姓名:关 山  彭 昶
作者单位:东北电力大学机械工程学院, 吉林 132012,东北电力大学机械工程学院, 吉林 132012
基金项目:吉林省科技厅科技攻关项目(20100204004SF)
摘    要:金属切削是一个非线性系统,刀具磨损产生的声发射信号具有混沌特征。该文采用混沌理论对刀具不同磨损程度的声发射信号进行非线性特性分析。首先采用经验模态分解与小波阈值结合(empirical mode decomposition and wavelet,EMD-Wavelet)的法对信号去噪,消除噪声对吸引子结构以及特征参数的影响。其次利用互信息法和Cao方法分别求时延和嵌入维,对去噪后的信号进行相空间重构。最后绘制吸引子相图,并求解特征参数关联维。结果表明,看似无序杂乱的非线性声发射信号有着内在的有序状态。吸引子结构随着刀具磨损状态的改变呈现一定变化规律,关联维数与刀具磨损状态有一定的对应关系。这些特性对于刀具磨损状态识别有一定的参考意义。

关 键 词:刀具;材料磨损;混沌理论;去噪;相空间重构;吸引子;关联维
收稿时间:2015-03-11
修稿时间:2015-05-12

Chaotic characteristic analysis of tool wear acoustic emission signal
Guan Shan and Peng Chang. Chaotic characteristic analysis of tool wear acoustic emission signal[J]. Transactions of the Chinese Society of Agricultural Engineering, 2015, 31(11): 60-65
Authors:Guan Shan and Peng Chang
Affiliation:School of Mechanical Engineering, Northeast Dianli University, Jilin 132012, China and School of Mechanical Engineering, Northeast Dianli University, Jilin 132012, China
Abstract:Abstract: In metal cutting process, surface quality and dimensional accuracy of the work piece is affected by cutting-tool wear condition. So it is important to study the cutting-tool wear, especially in automation production. Cutting-tool wear is a complex process; it is affected by various factors like cutting parameters, material characteristics and cutting environment, etc. Metal cutting is a nonlinear system; there are a lot of non-stationary signals used in condition monitoring and fault diagnosis. Vibration, force and acoustic emission (AE) are the typical signal type widely used in cutting-tool wear research. In this paper, we chose AE signal to be the carrier in analyzing cutting-tool wear. AE is the class of phenomena where transient elastic waves are generated by the rapid release of energy when the materials are distorted or under the outside load. The AE signal produced by cutting -tool wear is high-frequency and the bandwidth is nearly 50 kHz-1 MHz, so it can weaken the influence of low-frequency noise like mechanical noise and ambient noise. The measured signal sometimes contains high-frequency noise. In this paper, chaos theory was used in analyzing the nonlinear characteristics of the AE signal. Chaos theory is sensitive to noise; therefore, noise reduction was done with the method based on empirical mode decomposition and wavelet (EMD-Wavelet) before computing. The signal were decomposed into several intrinsic mode functions which was from high-frequency to low-frequency by use of EMD, then it was used to determine the noise dominated intrinsic mode functions based on consecutive mean square error (CMSE) proposed by Boudraa and then restrained them. A new signal were reconstructed by adding the rest intrinsic mode functions together and a further and last de-noising was using wavelet to processing the new one in order to get more pure signal. Before extracting the chaotic character, an important step was to reconstruct a phase space from the de-noised signal. To get the phase space vector, two key parameters, delay time and embedding dimension, had to be determined. Method based on mutual-information was utilized in computing delay time and Cao method for embedding dimension. After reconstructing the phase space, the chaos attractor was presented which can obviously reflect the cutting-tool wear condition. The structure of the attractor differed with tool wear. In order to prove the effect of noise reduction, a comparison was done between attractors another one reconstructed from original signal. The attractor reconstructed from the purified signal was smoother than the noisy signal. To get accurate result, the correlation dimension was computed. The result showed that seemingly random AE signal has internal ordered state and there was a certain correspondence between the correlation dimension and tool wear. So the chaos character can be used in cutting-tool wear identification and the result can offer a reference for cutting-tool wear condition monitoring.
Keywords:tools   wear of materials   chaos theory   denoising   phase space reconstruction   attractor   correlation dimension
本文献已被 CNKI 万方数据 等数据库收录!
点击此处可从《农业工程学报》浏览原始摘要信息
点击此处可从《农业工程学报》下载全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号