筒式结构拆除的力学分析

根据力学原理，分析讨论了钢筋混凝土筒式结构定向倾倒的切口高度和切口角度．     

Some Comments on Gerechte Designs

In a companion paper we derived the correct analysis for gerechte designs with uncorrected errors. Here we show that this correct analysis cannot be justified by the usual randomization argument. However, when the regions are rectangular there is a randomization procedure which validates an analysis with three separate error terms. We also outline other developments in design and analysis that may be more satisfactory.     

木瓜剖分原理研究及新机型设计

针对我国目前对木瓜剖半设备研究较少,剖切方式不合理,切割效果差等问题,设计开发了新型木瓜剖半机。该机切割方式选用滑切切割的方式,由运料系统、切割系统、出料系统组成,设计合理,结构简单。为此,计算了滑切角、切割角等主要切割参数,并给出了新型剖半机的主要技术参数。试验表明:该机切割效果好,能够有效提高生产效率。     

确定插齿刀廓形的方法及精度分析

论述了由插齿刀前锥面和螺旋面方程确定的母面廓形,提出了保证插齿刀原始廓形角的3个条件,由此推出了计算廓形角的3种方法,得出了廓形角及基圆半径的计算公式,然后对3种方法的误差进行分析,计算表明第3种方法误差较小,是一种较好方法。     

THE EFFECTS OF PATIENT POSITIONING AND SLICE SELECTION ON CANINE ACETABULAR ANGLE ASSESSMENT WITH COMPUTED TOMOGRAPHY

Acetabular angles (AAs) and dorsal acetabular rim angles acquired by computed tomographic (CT) imaging have been used to assess patient response to juvenile pubic symphysiodesis surgery. The purpose of this study was to evaluate the effects of patient positioning and slice selection on these angles, and an attempt was made to devise a repeatable method of measuring these angles that would eliminate positioning effects. We found significant variation in AAs with small differences in pelvic tilt and slice selection. Dorsal acetabular rim angles were not affected. As a result of positioning differences from one CT study to the next, every attempt should be made to standardize pelvic tilt, or eliminate its effect on AAs by standardizing gantry angle in relation to an anatomic landmark that will not change over time. The floor of the sacral vertebral canal may be a reasonable landmark for this purpose and deserves further study.     

几种除草剂药液表面张力、叶面接触角与药效的相关性研究

在除草剂氟磺胺草醚、灭草松和精喹禾灵药液中添加不同浓度的喷雾助剂ABS(十二烷基苯磺酸钠)和JFC ,以温室盆栽法测得各处理抑制杂草的效果,结果表明,在多数情况下添加喷雾助剂可使3种供试除草剂的药效显著提高。     

基于逆向工程的搅浆刀作业性能界定与关键设计参数研究

水田搅浆是基于稻作制度的独立机械化作业环节,搅浆刀是进行搅浆农艺处理的专用刀具,但目前缺乏针对搅浆的农艺界定及搅浆刀专用设计参数研究.本文利用逆向工程技术获取搅浆刀的关键几何参数,并对搅浆作业和搅浆刀的设计方法进行定义.通过与常规旋耕刀(R245)进行分析对比提出搅浆刀的专用设计参数,进而通过田间试验进一步探讨搅浆刀的...     

不同安放角度对污水搅拌器水力特性的影响

为深入对比污水处理池中搅拌器不同安放角度对其水力特性的影响,文中基于Fluent对搅拌器在不同安放角度下的水力特性进行数值模拟,得出适合搅拌器工作的较优工况.利用标准k-ε湍流模型及SIMPLEC算法对不同工况进行模拟,对比相应的流速分布和搅拌器中心所在平面的速度分量.结果表明:当搅拌器安放角度为-15°时,处理池内平...     

Effects of temperature and humidity on the contact angle of pesticide droplets on rice leaf surfaces

The effects of external factors such as temperature, humidity, pesticide formulation, and pesticide concentration on the contact angle of pesticide droplets on rice leaf surfaces were analyzed. The experiments showed that there were significant differences in the contact angles of droplets on the leaf surfaces under different temperatures and humidity. As the ambient temperature increased, the contact angle first decreased and then increased, reaching a minimum value at 25°C. With a gradual increase in humidity, the contact angle significantly increased and reached a maximum at 100% humidity. Finally, it was concluded that both the formulation and concentration of the pesticide had a significant effect on the contact angle of droplets on rice leaf surfaces. The experiments also illustrated that the effects of the pesticide formulation and concentration on the contact angle were more significant than those of temperature and humidity.     

板料激光斜冲击下受力变形数学分析

金属板材的激光冲击成形通常采用激光束垂直作用于工件表面,产生垂直于表面的冲击波作用力使板料变形,但在曲面零件成形时很难满足法向垂直冲击,因此有必要对斜冲击下板料力学变形特性进行研究。本文研究了激光斜冲击受力变形模型,对板料深度方向(z轴)变形公式、板料短轴(y轴)在水平方向上变形公式进行了理论推导计算,通过把两变形合成,得到短轴(y轴)在空间内总变形公式,最后把实验测量结果与理论计算结果进行了比较,得出两者相符的结论。