Assessment of the usage of biodegradable polymeric matrix in vaginal devices to sustain progesterone release in cows

The usage of timed artificial insemination (TAI) at a low cost leading to better reproductive rates has been the aim of several research groups in the field. Usually during TAI protocols, sustained progesterone (P₄) release devices are employed. Most devices are constituted of a nylon skeleton covered with a silicon layer with P₄. A device based on biopolymers was developed in order to reduce costs and decrease its environmental impact. In this study, we compared the kinetics of sustained progesterone release among devices manufactured with a polymeric blend made of polyhydroxybutyrate‐valerate (PHBV) and poly‐ε‐caprolactone (PCL) (DISP) which were compared with DIB® (Internal Bovine Device) used as the control. In the in vitro and in vivo progesterone release tests, two types of biopolymer‐based devices with a superficial area of 147 cm² were used: DISP8 (46% PHBV, 46% PCL and 8% P₄; n  = 4), DISP10 (45% PHBV, 45% PCL, 10% P₄; n  = 4) and DIB® (1 g P₄, 120 cm² area; n  = 3). The in vitro tests were carried out according to USP XXIII specifications and were performed in a dissolutor sink using an alcohol/water mixture (60/40 v/v) as a release media and samples were collected at 2 min, 2, 4, 8, 12, 24, 48, 60, 72, 84 and 96 h. P₄ concentrations were measured through spectrophotometry in a 244 nm long wave. Three to 3 comparisons of angular coefficients of the straight lines obtained by regression analysis of accumulated P₄ concentrations as a function of square root of time were carried out. Furthermore, the diffusion coefficient values of P₄ were also determined for DISP8 and DISP10. The results showed that the concentrations of P₄ were higher in the DISP10 (774.63 ± 45.26 μg/cm²/t^1/2) compared to DISP8 (566.17 ± 3.68 μg/cm²/t^1/2) (P  < 0.05). However, both DISP10 and DISP8 P₄ concentrations did not differ from DIB® (677.39 ± 16.13 μg/cm²/t^1/2). For the analysis of released quantities per day of the in vitro test, four periods were considered: 0–24, 24–48, 48–72 and 72–96 h. In the first 24 h, DISP8 released significantly less P₄ than DISP10 or DIB®, which did not differ among them. Between 24 and 48 h, DISP10 released significantly more P₄ than DIB®. DISP8 released an intermediate P₄ amount and did not differ significantly from DIB® or DISP10. Between 48 and 72 h, P₄ quantity released by DISP10 was significant higher (P  < 0.01) than that of DIB® and DISP8, which did not differ among themselves. Between 72 and 96 h, DISP10 released significantly more P₄ than DIB®, and DISP8 released an intermediate amount which did not differ from DIB® or DISP10 (P  < 0.01). There was interaction between treatment and time (P  = 0.0024). The diffusion coefficient values were: 1.36 × 10^?8 (cm²/s) for DISP10 and 1.12 × 10^?8 (cm²/s) for DISP8. For the in vivo test, ovariectomized crossbred cows received DIB® (n  = 4) or DISP8 (n  = 8) in an alternate design with a non‐balanced sequence (cross‐over) added of measures repeated in time referring to 16 days of blood samples collection. Samples were analyzed through radioimmunoassay in solid phase using the commercial kit of DPC (Diagnostics Products Corporation). Plasma concentrations of P₄ peaked at 4 h after the placement of the device, this being the only time in which plasma P₄ concentrations differed between DIB® (11.45 ± 1.96) compared with DISP8 (9.23 ± 1.15 ng/mL) (P  = 0.027). On day 8, plasma P₄ concentrations were similar for DIB® (2.44 ± 0.09) and DISP8 (1.89 ± 0.13 ng/mL) (P  = 0.58) showing that both devices were able to keep P₄ concentrations above 1 ng/mL in the plasma of the cow during the 16 day in vivo test. In conclusion, devices manufactured with the blend of PHBV/PCL biopolymers can sustain the release of P₄ in a similar manner as silicon.     

Changes in the Molecular Characteristics of Bovine and Marine Collagen in the Presence of Proteolytic Enzymes as a Stage Used in Scaffold Formation

Biopolymers, in particular collagen and fibrinogen, are the leading materials for use in tissue engineering. When developing technology for scaffold formation, it is important to understand the properties of the source materials as well as the mechanisms that determine the formation of the scaffold structures. Both factors influence the properties of scaffolds to a great extent. Our present work aimed to identify the features of the molecular characteristics of collagens of different species origin and the changes they undergo during the enzymatic hydrolysis used for the process of scaffold formation. For this study, we used the methods of gel-penetrating chromatography, dynamic light scattering, reading IR spectra, and scanning electron microscopy. It was found that cod collagen (CC) and bovine collagen (BC) have different initial molecular weight parameters, and that, during hydrolysis, the majority of either type of protein is hydrolyzed by the proteolytic enzymes within the first minute. The differently sourced collagen samples were also hydrolyzed with the formation of two low molecular fractions: Mw ~ 10 kDa and ~20 kDa. In the case of CC, the microstructure of the final scaffolds contained denser, closely spaced fibrillar areas, while the BC-sourced scaffolds had narrow, short fibrils composed of unbound fibers of hydrolyzed collagen in their structure.     

Polymer-Based Electrophoretic Deposition of Nonwovens for Medical Applications: The Effect of Carrier Structure,Solution, and Process Parameters

Hyaluronate and alginate are non-toxic and biocompatible polymers, which can be used for surface modification and functionalization of many kinds of materials. Electrophoretic deposition (EPD) has several advantages, including its versatility, simplicity, and ability to coat substrates with complex shapes, and is used for the creation of antimicrobial or hydrophobic coatings on metallic biomaterials, among other applications. However, its utilization for applying biopolymer layers on textiles is very limited due to the more complex structure and spatial characteristics of fibrous materials. The aim of this research was to analyze the effects of selected EPD process parameters and the structural characteristics of fibrous carriers on the kinetics of the process and the microscopic characteristics of the deposited layers. The influence of solution characteristics, process parameters, and carrier structures obtained using two different techniques (melt blown and spun-bonded) were analyzed. The morphology and structure of the created deposits were analyzed using scanning electron microscopy and computed tomography, and molecular structure analysis was performed with Fourier Transform Infrared spectroscopy. The surface mass and thickness of fibrous poly (lactic acid)-based carriers were analyzed in accordance with the respective standards. This study serves as a basis for discussion and further development of this method with regard to fibrous materials for medical applications.     

A Comparative Study on the Flocculation of Silica and China Clay with Chitosan and Synthetic Polyelectrolytes

Flocculation is still one of the most important and efficient processes for water treatment. However, most industrial processes, such as in water treatment plants, still use huge amounts of synthetic polyelectrolytes for the flocculation process. Here we compare the flocculation of two different suspended particles, i.e., silica particles and china clay, with the biopolymer chitosan and two common strong synthetic polyelectrolytes. As a flocculant, chitosan featured a minimum uptake rate of 0.05 mg/g for silica and 1.8 mg/g for china clay. Polydiallyldimethylammonium chloride (PDADMAC) for comparison possessed a minimum uptake rate of 0.05 mg/g for silica and 2.2 mg/g for china clay. Chitosan as an environmentally friendly biopolymer competes with the synthetic polyelectrolytes and thus represents a beneficial economic alternative to synthetic flocculants.     

Adsorption of Cationic Dyes on a Magnetic 3D Spongin Scaffold with Nano-Sized Fe3O4 Cores

The renewable, proteinaceous, marine biopolymer spongin is yet the focus of modern research. The preparation of a magnetic three-dimensional (3D) spongin scaffold with nano-sized Fe₃O₄ cores is reported here for the first time. The formation of this magnetic spongin–Fe₃O₄ composite was characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential thermal analysis (DTA) (TGA-DTA), vibrating sample magnetometer (VSM), Fourier-transform infrared spectroscopy (FTIR), and zeta potential analyses. Field emission scanning electron microscopy (FE-SEM) confirmed the formation of well-dispersed spherical nanoparticles tightly bound to the spongin scaffold. The magnetic spongin–Fe₃O₄ composite showed significant removal efficiency for two cationic dyes (i.e., crystal violet (CV) and methylene blue (MB)). Adsorption experiments revealed that the prepared material is a fast, high-capacity (77 mg/g), yet selective adsorbent for MB. This behavior was attributed to the creation of strong electrostatic interactions between the spongin–Fe₃O₄ and MB or CV, which was reflected by adsorption mechanism evaluations. The adsorption of MB and CV was found to be a function of pH, with maximum removal performance being observed over a wide pH range (pH = 5.5–11). In this work, we combined Fe₃O₄ nanoparticles and spongin scaffold properties into one unique composite, named magnetic spongin scaffold, in our attempt to create a sustainable absorbent for organic wastewater treatment. The appropriative mechanism of adsorption of the cationic dyes on a magnetic 3D spongin scaffold is proposed. Removal of organic dyes and other contaminants is essential to ensure healthy water and prevent various diseases. On the other hand, in many cases, dyes are used as models to demonstrate the adsorption properties of nanostructures. Due to the good absorption properties of magnetic spongin, it can be proposed as a green and uncomplicated adsorbent for the removal of different organic contaminants and, furthermore, as a carrier in drug delivery applications.     

Market and technical challenges and opportunities in the area of innovative new materials and composites based on nanocellulosics

This communication is a review over the major market and technical challenges and opportunities for nanocellulosic materials on a large scale but in low-to-medium-end markets. Basically, the potential use of nanocellulose as a wet-end strength additive in papermaking has been known for decades, but not come into operation because of the high-energy costs of producing these materials. Cost performance compared to starch derivatives is one challenge, and the other is to design suitable dewatering/retention aid systems. Other paper applications are as a surface-sizing agent and as a barrier coating material. Major challenges are associated with the high viscosity of nanocellulosic materials and how to apply the nanocellulose in order to obtain good surface coverage. There are several opportunities in the nanocomposite markets. The packaging sector together with the automotive sector and the building sector constitute large potential markets. Challenges are related to the mixing of hydrophobic and hydrophilic materials so that a good dispersion of nanocellulose is obtained. Scaling up of nanocellulose production processes and procedures for nanocomposite manufacturing in order to obtain price–performance in the various applications remains, as expected, the largest challenge     

Growth, survival, quality and digestive enzyme activities of larval shrimp fed microencapsulated, mixed and live diets

An artificial diet for shrimp larvae was microencapsulated with a polysaccharide blend [66% gum arabic, 17% mesquite gum and 17% maltodextrin 10 dextrose equivalent (DE)]. Microencapsulated diet (MD) was fed to mysis alone, as a co‐feed with the microalgae Chaetoceros cerastosporum and Tetraselmis chuii (mixed) and compared with a live diet (control) of C. cerastosporum, T. chuii and Artemia nauplii. No significant differences (P > 0.05) were detected in growth rates, development and quality indexes of larvae fed the three experimental diets. All diets supported survival percentages of >90%. Shrimp larvae fed MD and mixed diets had higher specific trypsin activity and soluble protein content than those fed live diet. Amylase activity decreased in larvae fed the mixed and MD apparently due to the carbohydrate composition of the diet. The results indicate that it is possible to substitute a live diet with a microencapsulated one (with a wall composition made up of a polysaccharide blend) in Litopenaeus vannamei mysis.     

Marine Biopolymers as Bioactive Functional Ingredients of Electrospun Nanofibrous Scaffolds for Biomedical Applications

Marine biopolymers, abundantly present in seaweeds and marine animals, feature diverse structures and functionalities, and possess a wide range of beneficial biological activities. Characterized by high biocompatibility and biodegradability, as well as unique physicochemical properties, marine biopolymers are attracting a constantly increasing interest for the development of advanced systems for applications in the biomedical field. The development of electrospinning offers an innovative technological platform for the production of nonwoven nanofibrous scaffolds with increased surface area, high encapsulation efficacy, intrinsic interconnectivity, and structural analogy to the natural extracellular matrix. Marine biopolymer-based electrospun nanofibrous scaffolds with multifunctional characteristics and tunable mechanical properties now attract significant attention for biomedical applications, such as tissue engineering, drug delivery, and wound healing. The present review, covering the literature up to the end of 2021, highlights the advancements in the development of marine biopolymer-based electrospun nanofibers for their utilization as cell proliferation scaffolds, bioadhesives, release modifiers, and wound dressings.