国产MJ3210小型木工跑车带锯机锯解正交试验分析

采用正交试验设计法，对国产MJ3210小型木工跑车带锯机的锯解质量进行研究。通过实测马尾松锯材尺寸偏差、表面粗糙度等参数，得到其最佳的进料速度、锯解厚度和锯卡高度的组合方案。结果表明，该设备具有结构简单、出材率高、锯解精度高、质量好、成本低和生产效率高等优点。     

激光脉冲在橘子表皮打标的效果研究

为满足水果追溯条码清晰、耐久的要求,选取橘子为试验对象,对比纳秒激光和皮秒激光在其表面打印二维码的效果.试验结果表明:与纳秒激光相比,皮秒激光在橘子表皮上打印的线条平直度佳,轮廓清晰,对表皮的损伤更小.     

LED水下集鱼灯光场分布数值模拟分析

为探究LED水下集鱼灯光色、功率、放置深度和海水叶绿素质量浓度对光场分布的影响,基于蒙特卡罗模拟方法建立了水下光束传输数值计算模型,通过控制变量法计算了不同条件下的水下光场分布,并提出以0.1～10.0 lx等值线所包围的面积与计算截面面积比值为相对有效光照范围(relative effective illumination range, REIR)。以REIR为评价指标,对不同条件下的光场分布进行了分析。结果显示：(1)相同功率条件下,REIR依次为绿光>白光>蓝光,以功率420W、叶绿素质量浓度0.1mg/m³为例,3种光色的REIR比值为1.58∶1.31∶1;(2)相同光色条件下,当叶绿素质量浓度为0.1mg/m³时,集鱼灯功率由420W增至1200W,蓝、绿、白3种集鱼灯的REIR分别由31.68%、50.27%、41.78%增至38.59%、56.91%、50.15%,功率增加近3倍,但REIR增幅有限;(3)随着集鱼灯放置深度增加,REIR先增加后稳定;以叶绿素质量浓度1.0mg/m³、功率为4...     

A Severe Hellenic CMV Tomato Isolate: Symptom Variability in Tobacco, Characterization and Discrimination of Variants

A severe strain of Cucumber mosaic virus (CMV) originating from an infected tomato plant (Gastouni-Olympia, Greece) was isolated in tobacco (Nicotiana tabacum cv. Xanthi nc), after three serial local lesion passages in Chenopodium quinoa and designated CMV-G. CMV-G induces yellow mosaic (YM) symptoms in tobacco. When CMV-G was passed mechanically through C. quinoa, phenotypic variants inducing YM or green mild mosaic (MM) in tobacco were isolated. Aphid transmission, from different hosts, appears to be an effective approach for separating MM variants of CMV-G from YM variants. In particular, aphid transmission from zucchini proved to be very efficient in selecting for MM variants. In contrast, aphids transmitted only YM variants from tomato plants. Molecular characterization of CMV-G and its progeny resulted in their classification in the CMV subgroup IB, free of satellite RNA, being the first discovery of the subgroup IB in Greece. In the Solanaceae family (tobacco, tomato, pepper) YM variants induced more severe symptoms than the MM variants. YM and MM phenotype was stable in tobacco for all seven passages tried using the obtained YM and MM variants. Cross-protection experiments showed that an isolated MM variant was able to protect tobacco plants against a challenge infection by a YM variant.     

Ca对AZ31镁合金CO2激光焊接接头组织和性能的影响

采用添加填充材料的CO2激光焊接工艺对AZ31镁合金薄板进行焊接,研究了不同Ca含量对焊缝金属的显微组织和力学性能的影响.结果表明：当激光功率为1 500 W,焊接速度为3 m/min时, AZ31镁合金CO2激光焊接的焊缝金属中添加一定量的σCa＜0.19%元素,可以得到成分相对较均匀、组织细小的焊缝.当填充带材为AZC04(焊缝中σCa=0.19%)时,焊缝区晶粒相对细小,析出相细小弥散,此时焊接接头的力学性能最优,焊接效率基本可达到100%.     

A spatially-explicit method to assess the dry deposition of air pollution by urban forests in the city of Florence,Italy

Urban forests (UF) provide a range of important ecosystem services (ES) for human well-being. Relevant ES delivered by UF include urban temperature regulation, runoff mitigation, noise reduction, recreation, and air purification. In this study the potential of air pollution removal by UF in the city of Florence (Italy) was investigated. Two main air pollutants were considered – particulate matter (PM₁₀) and tropospheric ozone (O₃) – with the aim of providing a methodological framework for mapping air pollutant removal by UF and assessing the percent removal of air pollutant.The distribution of UF was mapped by high spatial resolution remote sensing data and classified into seven forest categories. The Leaf Area Index (LAI) was estimated spatially using a regression model between in-field LAI survey and Airborne Laser Scanning data and it was found to be in good linear agreement with estimates from ground-based measurements (R² = 0.88 and RMSE% = 11%). We applied pollution deposition equations by using pollution concentrations measured at urban monitoring stations and then estimated the pollutant removal potential of the UF: annual O₃ and PM₁₀ removal accounted for 77.9 t and 171.3 t, respectively. O₃ and PM₁₀ removal rates by evergreen broadleaves (16.1 and 27.3 g/m²), conifers (10.9 and 28.5 g/m²), and mixed evergreen species (15.8 and 31.7 g/m²) were higher than by deciduous broadleaf stands (4.1 and 10 g/m²). However, deciduous forests exhibited the largest total removal due to the high percentage of tree cover within the city. The present study confirms that UF play an important role in air purification in Mediterranean cities as they can remove monthly up to 5% of O₃ and 13% of PM₁₀.     

Sampling Investigation on Inhatitant Domestic Tap Water Consumption Situation and It’s Characteristics Analysis

Economics.Through sampling investigation and analysis on inhabitant domestic tap water consumption situation,it is given that economic factors are the main factors influence inhatitant's water consumption.The functional relations among inhabitant's income and water consumption,water price and consumption are given. The tap water's income elasticity of demand and price elasticity of demand is analyzed, along with the fluctuating range month by month of inhabitant's water consumption.Finally ,this paper offers the reference data for planning the ability of water supply and making policies of ladder water prices.     

选区激光熔化316L不锈钢多孔过滤零件的组织性能研究

【目的】揭示选区激光熔化316L不锈钢粉末成型多孔过滤零件的成型规律和机理。【方法】试验设计孔洞尺寸为1 mm的圆形、正方形多孔316L不锈钢过滤零件,采用选区激光熔化方法进行成型,选用光学显微镜、扫描电子显微镜、X射线衍射等手段对其组织特征和性能进行分析检测,采用显微硬度计测量其显微硬度。【结果】获得了无气孔、裂纹、偏析等缺陷,且致密度达到95%的成型组织。组织内部主要由垂直于界面呈现外延生长的树枝晶组成,所得组织分层均匀,各层间呈冶金结合,定向凝固特征明显。【结论】多孔过滤零件成型件由奥氏体组成,显微硬度为:258~294 HV0.3。采用选区激光熔化方法可以成型孔洞尺寸较小的过滤零件。     

砒砂岩区水力侵蚀下坡面微地貌变化特征及过程研究

解决砒砂岩区坡面的产流产沙问题对黄河流域生态安全具有重要意义,选取砒砂岩裸露坡面为研究对象,在自然降雨条件下采用野外径流小区实测结合三维激光扫描技术,分析13次有效降雨过程砒砂岩坡面微地貌的变化过程及产流产沙特征.结果表明,径流小区内坡面土壤平均侵蚀深度为26 mm,侵蚀区占径流小区总面积的95.27％,单位面积上侵蚀...     

Occurrence of a new leaf spot disease ofMusa sp. incited byThanatephorus cucumeris

A new leaf spot disease of banana(Musa sp.) cv. ‘Rasthali’ (syn. Silk) was observed in Tamil Nadu, in 1987. The causal organism was isolated in pure culture and identified asRhizoctonia solarii Kühn. The teleomorphic stage,Thanatephorus cucumeris (Frank) Donk, has also been induced artificially. This is the first record of this pathogen causing leaf spot disease onMusa sp. The pathogenicity of basidiospores on several other important crops was also tested.