机械化奶站真空系统的设计

阐述了机械化奶站真空系统的组成、真空泵的工作原理、真空系统设计中应遵循的原则及设计过程中的注意事项,提出了设计机械化挤奶站真空系统的方法。     

Effects of temperature,vapour pressure deficit and radiation on infectivity of conidia ofBotrytis cinerea and on susceptibility of gerbera petals

The effect of vapour pressure deficit, temperature and radiation on the postharvest susceptibility of gerbera flowers toB. cinerea, on the water relations of gerbera flowers and on the lesion formation after conidial infection ofB. cinerea was studied. The temperature range in whichB. cinerea could germinate and growin vitro is 5–30 °C. In climate chamber experiments flowers had more lesions ofB. cinerea at temperatures of 20 and 25 °C than at 10 and 15°C. At 15, 20 and 25°C the infectivity ofB. cinerea conidia was negatively affected during a storage-period of 7 days. At a vapour pressure deficit (VPD) of 200 Pa significantly more conidia ofB. cinerea were infective than at 800 Pa. At a VPD of 800 Pa the susceptibility of gerbera flowers forB. cinerea was not significantly different than at 200 Pa. High radiation levels in glasshouses in spring and summer negatively influenced the infectivity of conidia ofB. cinerea on the flower surface, but did not affect the susceptibility of gerbera flowers forB. cinerea. In spring and early summer conidia lost their infectivity at high radiation levels, high temperatures and high levels of VPD. In summer gerbera flowers could be more susceptible toB. cinerea because of high temperatures in glasshouses, but the negative effect of radiation on the conidia ofB. cinerea seemed to overrule the temperature effect. Thus, the numbers of lesions in spring and summer can be low compared with the numbers in other seasons, although the numbers ofB. cinerea colonies on spore traps can be high. The effect of temperature on the susceptibility of gerbera flowers can probably be explained by changes of water status in the petals. At higher temperatures the number of lesions and the turgor (=water potential—osmotic potential) in the petals increased. Temperatures <10°C during lesion formation (RH>95% and VPD<50 Pa) had a temporary negative effect on the number of lesions. After 3 days of incubation the numbers of lesions were about equal (30 lesions/cm²) from 5 to 20°C. At 30°C no lesion formation was observed even after 3 days.     

苹果低氧气调新组合贮后效应的利用研究

利用0.12mm聚乙烯薄膜大帐进行低氧气调新组合的较大规模应用试验,对2394kg玫瑰红苹果进行低氧处理,帐内O2浓度可下调至约2%,CO2浓度可自动维持在5%～8%的较理想状态,处理结束后很易转为MA自发气调。低氧处理后再MA贮藏的苹果,虎皮病果率低、症状轻,腐烂果少,果柄和果皮新鲜,叶绿素保持效果好,果肉硬度明显高于小包装气调和冷藏对照。说明利用塑膜大帐进行前期低氧新组合处理与后期自发气调、实现低氧气调新组合贮后效应的利用是可行的。     

利用ZXX-65真空循环熏蒸设备熏蒸仓储害虫的研究

用ZXX-65真空循环熏蒸设备在不同真空压力、熏蒸时间、药剂浓度条件下对选定的典型仓储实验试虫进行熏蒸，根据杀虫效果，筛选出害虫的最优熏蒸条件组合。结果表明，ZXX-65真空循环熏蒸设备可以在2h内杀死各种仓储害虫。40000Pa，60g/m^3，2h为仓储害虫的最优熏蒸条件组合。     

应用真空熏蒸技术杀灭蔗扁蛾

利用真空熏蒸技术对受蔗扁蛾Opogona sacchari Bojer危害的发财树进行了真空熏蒸处理.结果表明,在真空条件下,仅需要较低的熏蒸剂量在较短的时间内即可全部杀死发财树里的蔗扁蛾,杀虫效果达100%,达到快速、高效、安全、环保的要求.为花卉害虫的处理提供了一种新的方法.     

聚脲喷枪混合室的设计和FLUENT仿真分析

为提高聚脲喷涂喷枪的混合效果，基于撞击流理论设计了一种新型聚脲喷涂喷枪的混合室。混合室采用两级撞击混合，分别采用两组T型和两组Y型对撞混合形式。利用SolidWorks设计混合室的结构模型后，利用FLUENT软件，采用冷、热水在混合室内撞击混合、对流传热的方法进行仿真模拟，并且计算了流体在混合室内的微观混合时间。结果表明:合理增加撞击流混合室的混合级数和采用多组T型、Y型对撞混合形式可增益混合效果；撞击流混合室的主要混合区是在撞击区；流体在喷枪内停留的总时间约为5.71 ms，满足具有反应迅速这一特性的材料的混合要求；微观混合时间小于1 ms，混合效果优异。      

隔膜计量泵的改良设计与汽蚀性能的提高

针对应用于石油化工装置上的进口隔膜计量泵容易产生的汽蚀问题，对隔膜泵复合隔膜、柱塞密封副、液压平衡与补偿阀结构进行了改良设计，采用较大承载能力的机座、独特阶梯式活塞、加大直径的活塞、PTFE＋NBR复合隔膜，改良放气安全阀及油浸没式补偿系统等方法，提高了隔膜计量泵的汽蚀性能；通过对改造的隔膜计量泵与原有的计量泵进行的汽蚀试验对比，给出了隔膜计量泵性能与现场使用的最佳匹配工况。改良的结构设计和新型材料的选用大大提高了计量泵的汽蚀性能。     

CNG发动机燃烧室形状对气流运动和燃烧特性的影响

为提高天然气发动机的燃烧品质,基于6105型涡轮增压CNG发动机,通过建模分析法,对发动机不同燃烧室形状对缸内气流运动和燃烧特性的影响进行了三维数值模拟研究。研究结果表明,燃烧室形状对挤流的形成和燃烧过程有着重要影响。缩口型燃烧室具有较大的挤流强度和较长的涡流持续期,火焰传播速度快,燃烧性能好,但其火花塞附近的热负荷较大,NOx的含量高。敞口型燃烧室挤流强度较弱,火焰传播速度较慢,燃烧性能最差。直口型燃烧室则介于两者之间,既能保证较快的火焰传播速度和较好的燃烧性能,又降低了其火花塞附近的热负荷和NOx的排放量,是较适合天然气发动机采用的燃烧室。     

小缸径直喷柴油机喷雾与燃烧三维数值模拟

应用CFD软件对一台小缸径增压中冷柴油机进行了喷雾燃烧数值模拟,得到了详细的喷雾发展形态、燃油浓度分布和燃烧过程温度场、有害排放物分布等重要信息,为燃烧室结构优化设计和与油嘴匹配奠定基础。计算结果表明,计算示功图与实测值吻合较好;喷油阶段,油束存在碰壁现象,燃烧室凹坑底部燃油浓度较高;随着活塞下行,锥台与凹坑连接处空气运动较弱,燃油浓度较高,同时NOx与Soot生成与混合气浓度、空气运动、温度有密切联系。