绿色富硒生物猪饲料中AFB1达标生产工艺优化研究

饲料中黄曲霉毒素(AFB₁)容易超标,检出率达80%~100%,毒性大,具强致癌性,可抑制生猪免疫机能,降低动物生产性能,引起动物继发感染,还会在动物产品中残留而威胁人类健康,给生猪养殖带来经济损失,降低猪肉食品安全性。本文通过使用先进固体发酵系统设备和益生菌发酵技术,采用单因素试验和响应面中试优化,获得发酵降解猪饲料AFB₁的最佳工艺参数为硒浓度0.3 mg/kg,发酵时间12 h,量子波强度30 Hz,益生菌菌种组合CGMCC NO.17328混合CGMCC NO.15611。该工艺将猪饲料AFB₁量从63.41μg/kg降解到2.98μg/kg,降解率达到95.30%,AFB₁含量达到国家饲料安全标准。生产工艺适合养猪场低成本快速生产AFB₁达标猪饲料。     

蜗壳式离心泵外特性仿真与实验研究

为探索不同仿真方法的适用性,对ns=157的单级蜗壳离心泵不同工况的扬程和效率进行定常和非定常计算,并分别分析了定常计算时不同叶片夹角及非定常计算时不同时间步长的影响,通过与实验对比,得到的主要结论有:定常计算仅适用于额定工况外特性仿真,其扬程和效率计算误差分别为4.9%和2.9%,而定常多相位的计算误差分别为7.1%和3.2%;非定常仿真计算时,以4°为时间步长,并间隔20°保存一次计算数据,较好地预测出扬程曲线走势,额定工况扬程和效率计算误差约1.1%和1.8%,但小流量和大流量区间扬程计算误差达到10%左右。因此在水力优化设计时,若只关注高效点位置及其扬程和效率,可采用定常计算,若还关注扬程曲线走势,则应采用非定常计算。     

基于有限元的汽车扭臂热锻工艺研究

文章以汽车扭杆力臂为研究对象,通过DEFORM-3D有限元分析对汽车扭杆力臂热锻工艺过程进行模拟试验,分析了成形过程中的上模载荷情况、应力应变场分布情况和温度场的变化规律。以提高产品质量和降低载荷为主要目的,给出合理的热加工参数,分析结果能为类似锻件的热模锻工艺和模具设计提供依据。     

Experimental investigation on the transport of different fish species in a jet fish pump

A jet fish pump with a throat of ø60 mm was designed to study its performance in the transport of different fish species and the physiological changes in fish thereafter. Experiments were conducted to investigate the fish transport rate and energy required to transport each ton of fish when transporting Carassius auratus, commonly known as the Chinese goldfish, Megalobrama amblycephala, or Wuchang bream, and Ctenopharyngodon idella, the grass carp. Fish were examined for external injuries as well as for several important enzymes and hormones which are indicators of tissue injury and stress. The results showed that the transport rate for all three species of fish rose dramatically with an increase in the primary stream rate. In this experiment, the transport rates of C. auratus, M. amblycephala and C. idella reached 2357 ± 37.2 kg ∙ h⁻¹, 2888 ± 41.6 kg ∙ h⁻¹, and 2060 ± 40.2 kg ∙ h⁻¹, respectively. However, both injury rate and energy required to transport each ton of fish increased no matter whether the primary stream rate was too low or too high. Considering both transport rate and injury rate, the mean primary stream rate of 80 m³ ∙ h⁻¹ was determined to be the optimal operating condition in this experiment. Fish were stressed and most likely some of their organs were damaged. However, most physiological indexes almost fully recovered after several hours.     

菠萝蜜种子淀粉制备香草兰微胶囊的工艺研究

以菠萝蜜种子淀粉为壁材,采用饱和水溶液法制备香草兰精油微胶囊,以包埋产率为指标,采用响应面分析法对微胶囊的包埋条件进行优化探讨。结果表明:5个单因素中,影响最显著的因素为壁芯材比例、包埋温度和包埋时间。响应面优化得到香草兰精油微胶囊的最佳工艺条件为壁芯材比例为7.5∶1;包埋时间72 min;包埋温度54℃,此条件下的包埋产率为(95.46±0.2)%,包埋率为(76.35±0.6)%,载油量为(27.73±0.3)%。试验证明,此条件结果与模型预测值相吻合,此工艺条件可为菠萝蜜种子淀粉包埋香草兰精油微胶囊工艺提供理论依据。     

Replacement of fish oil in plant‐based diets for Pacific white shrimp,Litopenaeus vannamei,by stearine fish oil and palm oil

Stearine fish oil (SFO) and palm oil (PO) have emerged as promising alternatives for the replacement of fish oil (FO) in aquafeeds. This study evaluated the replacement of FO with alternative oils in practical diets for Litopenaeus vannamei. In a clear brackish water study (14.1 g/L) utilizing shrimp (0.29 ± 0.02 g, initial weight), FO was replaced by SFO at inclusion ratios of 100:0, 75:25, 50:50, 25:75, and 0:100 (FO:SFO) and PO as 90% of FO. After 55 days, no significant differences (p < 0.05) in final weight, growth, or survival of shrimp were observed. A second trial (8 weeks) in low‐salinity water (2.1 g/L) with shrimp (0.92 ± 0.02 g, initial weight) evaluated diets with 100% FO, 100% SFO, 90% PO, 90% soybean oil (SO), or 90% flaxseed oil (FXO) as a replacement for FO and four commercially produced diets with 2% of FO, SO, PO, or FXO. One treatment received half rations of the commercial FO diet, and one treatment was based entirely on natural productivity. Results show that the fatty acid profiles of the tail muscle conformed to the lipids of the feed, and highly unsaturated fatty acids (HUFAs) were preserved. Following 8 weeks of culture, there were no significant differences in production performance.     

品种间大豆脂肪氧化酶活性差异及β-胡萝卜素漂白性研究

为了解东北地区大豆品种间大豆脂肪氧化酶(LOX)活性差异规律,整理适于东北地区种植的大豆种质资源307份(6份半野生品种,17份地方品种及4份国外品种,其余为栽培品种),统一种植,秋季收获后,测定各品种成熟籽粒脂肪氧化酶总活性。分析品种间脂肪氧化酶总活性分布规律、大豆脂肪氧化酶总活性与β-胡萝卜素漂白性之间关系。结果表明,307份大豆品种间脂肪氧化酶总活性差异极显著,平均值为21.68 U·mL~(-1),最小值为2.51 U·mL~(-1),最大值为42.38 U·mL~(-1)。根据脂肪氧化酶总活性差异,通过聚类分析将307份大豆品种分为3类。低活性品种占总量43.65%,脂肪氧化酶总活性平均值为15.25 U·mL~(-1);中等活性品种占总量43.97%,脂肪氧化酶活性平均值为24.64 U·mL~(-1);高活性品种占总量12.38%,脂肪氧化酶总活性平均值为33.87 U·mL~(-1)。脂肪氧化酶总活性与油分含量呈正相关,与蛋白含量呈负相关,与漂白性呈正相关。     

Engineered-airlift pumps for aquaculture applications using multiphase flow analysis

Currently, very few aquaculture operations are employing airlift pump technology for water recirculation, aeration, and waste removal. This is likely due to the poor design and lower efficiency of traditional airlift design, the limited amount of research effort that has been invested in improving performance capabilities of air lift pumps and the general lack of awareness of the industry about the inherent advantages of airlift systems. A new efficient airlift pump is hydrodynamically designed by incorporating the Volume of Fluid (VOF) multi-phase model along with the K-ε turbulence model utilizing Computational Fluid Dynamics (CFD) tools. The pump is designed to offer a substantial reduction in total energy usage as well as an improved quality of the culture products in order to make it attractive to aquaculture industry. In this study, both numerical and experimental investigations were carried out for airlift systems operating under two different submergence ratios of 50% and 90% in a lab setting using 2.54 cm diameter pumps. Also, the performance of a large-scale pumps of 10.16 cm diameters were also tested in an aquaculture raceway to determine its effect on the operation. The numerical results were found to be in agreement with the experiments within ±20% which is considered very reasonable for multiphase flow analysis. The present study was found to present a great tool for modelling the airlift pump performance, and potentially proposing new designs.     

叶轮出口边对双蜗壳泵压力脉动的影响

泵的叶轮扫掠蜗壳隔舌时产生的压力脉动是引起船用泵振动噪声的原因之一.为尽可能弱化这一影响,分别设计了叶片出口边与前后盖板基本面垂直和倾斜的2种不同形式叶轮,将其配置在相同的双蜗壳中,通过数值计算与样机试验相结合的手段,对蜗壳内9个不同位置的压力脉动情况进行对比分析.结果表明:出口边倾斜的叶轮相比于出口边垂直的叶轮可明显改善蜗壳内次脉动的“驼峰”现象,且可以进一步降低隔舌处主波动的压力峰值;对蜗壳内2个隔舌稍前的位置,出口边倾斜的叶轮反而会使得该点的压力系数幅值明显增大,且该点主波动的周期数发生改变;2种叶轮出口边的不同形式对蜗壳出口位置的压力脉动的影响基本相同;采用出口边倾斜叶轮对改善因叶轮与隔舌间的液流压力脉动是可行的.     

同源四倍体及其原二倍体黑皮冬瓜光合光响应模型筛选

为了筛选出最适合黑皮冬瓜Benincasa hispida (Thunb.) Cogn.的光合光响应模型,为其育种提供理论依据,以同源四倍体及其原二倍体黑皮冬瓜为试验材料,对8种经典的光合光响应模型适用性进行了比较分析。结果表明：二次多项式能够表现出光抑制情况,但在拟合过程中出现暗呼吸速率为正值、光补偿点为负值及无法解释当光强达到饱和后光合速率快速下降的问题;直角双曲线、非直角双曲线及指数函数Ⅰ、指数函数Ⅱ无法直接求取光饱和点、光补偿点,结合常用的光饱和点的计算方法得到的光饱和点与实测值均存在较大的偏差,且指数函数Ⅱ在计算光饱和点时表现出明显的人为性,也无法拟合光抑制情况,但4种模型拟合得到的光补偿点均与实测值相差不大;指数修正模型因系数β为负值,无法求取四倍体黑皮冬瓜材料的光饱和点和最大净光合速率,且拟合得到的四倍体黑皮冬瓜的光补偿点明显低于实测值;直角双曲线修正模型计算得到的暗呼吸速率及二倍体黑皮冬瓜的光饱和点明显低于实测值,但获得的四倍体及其二倍体的最大净光合速率与实测值最接近,说明其在拟合最大净光合速率上有优势;整体上分段函数计算得到的黑皮冬瓜的各光合参数与实测值最为接近,与实测值的平均相对误差最小,也能很好的拟合发生光抑制部分的光响应曲线。分段函数拟合同源四倍体及其原二倍体黑皮冬瓜光合光响应曲线效果较其他模型效果好,分段函数模型为黑皮冬瓜最适合的光合光响应模型。