固支矩形底扁球壳的边界几何缺陷

In this paper, concept of boundary geometrical imperfection during postbuckling process for shallow spherical shell is first presented. The effects of the declination of the rectangular boundary on postbuckling process are also studied by integrated metho     

卷边板件屈曲分析的半能量法

A semi-energy method to analyse the buckling behaviour of edge-stiffened plates under combined compression and bending is presented in this paper, One unloaded edge of the plate is restrained elastically against rotation and the other is stiffened by a st     

两端不等弯矩作用下薄壁梁柱的弯扭屈曲

本文采用Ｒａｙｌｅｉｇｈ－Ｒｉｔｚ法求解两端不等弯矩作用下单轴对称开口薄壁截面梁柱弯扭屈曲临界荷载，分析中考虑了三种常见的边界条件以及屈曲前变形的影响，将本文弯扭屈由临界荷载理论值与试验值比较，吻合较好。     

变截面构件的剪应力计算

变截面构件的弯曲变形是实际构件常见变形之一，现行钢筋混凝土设计规范提供的和实际设计计算应用的剪应力计算公式未考虑截面变化的影响，有较大的误差。本文用材料力学方法推出考虑变截面影响的剪应力计算公式，以便在实际设计计算应用。     

开口薄壁结构弯扭屈曲能量原理的有限变形理论分析

The formulas of the total potential energy of arbitrary thin- walled open cross section member counting in the geometric non-linear factors is deduced. The deductions are based on the most general finite deformation theory and the two assumptions that"the     

The Influences of Surrounding Rock Deformation in Deep Roadway under Different Supporting Structures

随着煤矿开采深度的不断增加，围岩变形特征更加复杂。基于ANSYS数值模拟软件，研究4种不同支护条件下深部巷道围岩的变形情况，研究结果表明：30MPa原岩应力作用下，联合支护产生的水平位移和垂直位移都要比其他支护小，变形影响区域也最小，最为适合围岩地质条件较差的巷道。     

THE REIMPROVEMENT FOR IMPULSE OF G. I. TAYLOR THEORY OF PLASTIC DEFORMATION IN IMPACT OF CYL1NDICAL PROJECTILES

In this paper the reimprovement for G. I. Taylor theory of plastic deformation in impact of cylindical projectiles is done. The impulse in the reimproved theory is G. I. Taylor' s 1/2, and 3/4 of G. I. Taylor' s improved theory. The analytical solution of the reimproved theory shows that it gives better agreement with exprimental results than those of the original Taylor' s theory and, the improved theory.     

Artificial Neural Networks Models for Flow Stress during High Temperature Plastic Deformation of Al-Li Alloy

Using gained experimental data to develop the models of stable flow stresses at high temperature plastic deformation by statistical methods for alloy materials, precision of the models is poor and at the same time the processes of modeling are complicated with great workload. On the basis of the data obtained on Gleeble-1500 Thermal Simulator,the predicting models for the relation between stable flow stress during high temperature plastic deformation and deformation strain, strain rate and temperature for 1420 Al-Li alloy have been developed with BP Artificial Neural Network method. The results show that the model on basis of BPNN is practical and it reflects the real feature of the deforming process. It states that the difference between the real value and the output of the model is in order of 5 percent.