水电站虹吸式进水口的控制

在对河北省几座已建虹吸式进水口水电站的虹吸控制方式进行分析对比的基础上,给出了一种采用液气射流泵将虹吸体抽成“低管”正虹吸,用“Y”形管中的水封保持真空,事故时利用“高管”自动补气破坏真空的控制系统,并分析了该系统的特点,给出了设计计算方法及计算公式。     

Water circulation induced by mechanical aerators in a rectangular vessel for shrimp aquaculture

A water streamer was designed for the purpose of enhancing cost-efficient circulation between the water surface and bottom of shrimp aquaculture ponds. We took direct measurements of the water current field induced by the designed aerator in a large rectangular reservoir of dimensions (L)50 × (W)19 × (D)1.3 m³ and compared the results with those of a standard Taiwanese paddle-wheel aerator. Vertical circulation between the surface and the bottom induced by the paddle wheel aerator was less than that by the designed aerator. Furthermore, the paddle-wheel aerator consumed more electric power than the designed aerator. The structures of water current induced by the two aerators are elucidated, and the advantages and disadvantages of the aerators are discussed.Auxiliary employment of the designed aerators may contribute to delivery of high DO water throughout the pond, which is more efficient than a paddle wheel aerator.     

聚脲喷枪混合室的设计和FLUENT仿真分析

为提高聚脲喷涂喷枪的混合效果，基于撞击流理论设计了一种新型聚脲喷涂喷枪的混合室。混合室采用两级撞击混合，分别采用两组T型和两组Y型对撞混合形式。利用SolidWorks设计混合室的结构模型后，利用FLUENT软件，采用冷、热水在混合室内撞击混合、对流传热的方法进行仿真模拟，并且计算了流体在混合室内的微观混合时间。结果表明:合理增加撞击流混合室的混合级数和采用多组T型、Y型对撞混合形式可增益混合效果；撞击流混合室的主要混合区是在撞击区；流体在喷枪内停留的总时间约为5.71 ms，满足具有反应迅速这一特性的材料的混合要求；微观混合时间小于1 ms，混合效果优异。      

液液系统中荷电射流不稳定性

针对生物柴油液液静电雾化乳化过程,建立了色散方程并应用Matlab进行数值计算,分析了水射流速度、荷电电压、水与生物柴油各自的黏度、表面张力对生物柴油中水射流不稳定性的影响.研究结果表明,在水-生物柴油系统中,提高水射流的速度或荷电电压,均能使界面波最大增长率增大,对应的最优波数也随之增加.水的黏度阻碍水射流的破碎雾化,而生物柴油黏度对水射流的破碎雾化却起着促进作用.水-生物柴油的界面张力越小,对液液静电雾化乳化过程越有利.在水-生物柴油液液静电雾化乳化实际应用过程中,除提高水射流速度和荷电电压外,提高水的温度同时尽可能地降低生物柴油的温度,可以形成粒径细小均匀离散相液滴,获得优质的生物柴油乳化燃油.     

2016/2017冬中国气温偏暖的基本特征及可能成因

利用中国740余站观测的月平均2 m气温资料以及NCEP/NCAR再分析资料,通过动力学诊断的方法,对2016—2017年中国冬季异常偏暖现象进行了研究。结果发现：中国2016—2017年冬季气温偏暖主要是由于西伯利亚高压和阿留申低压偏弱导致东亚冬季风偏弱,在中国存在异常的偏南风。阿留申低压偏弱由两个因素引起,一是由于阿留申群岛地区的海温偏低,冷源对应异常高压导致阿留申低压偏弱;二是阿留申低压在东亚副热带高空西风急流出口区以北,然而该冬季高空西风急流出口区位置偏南,导致阿留申地区偏离急流出口减压区,从而导致阿留申低压偏弱。此外,西风带偏北,中高纬亚洲大陆上空以纬向环流为主,不利于冷空气南下。     

支管射流三通结构优化与试验

为了提高支管射流三通水力性能,改善滴灌的灌水均匀性,基于CFX数值模拟技术,对进口宽度为15 mm的支管射流三通进行结构优化.选取位差、劈距、劈尖半径和侧壁倾角为影响因素,通过四因素三水平正交设计了9组模型,边界条件设定为进口压力100 kPa.选取支管射流三通出口设计流量为评价标准,支管射流三通最优结构尺寸为位差5.5 mm、劈距113 mm、劈尖半径13 mm、侧壁倾角10°.此结构尺寸参数下的支管射流三通水力性能试验结果表明:在进口水压为100 kPa时,支管射流三通脉冲频率为148次/min,水头压力振幅为37.9 kPa,水头压力损失为16.7 kPa,出口流量为0.698 L/s;支管射流三通所接滴灌带长度为60 m时,与普通支管三通相比,支管射流三通的灌水均匀系数提高了2.78%,流量偏差率降低了4.72%.该研究可为射流技术在脉冲滴灌系统的研究、开发与应用提供理论依据.     

水肥一体化中水肥混合效果数值模拟研究

为研究水肥一体化技术中的水肥混合特性,以流体力学中的两相流理论为基础,针对水肥混合过程中混合时间、混合区间长度、流速及管径对其混合效果的影响进行相应的数值模拟研究。结果表明,混合时间及混合区间长度越长有利于提高水肥混合效果及最终水肥混合均匀性;水肥流速比较低时管内水肥混合的均匀性较好,且水肥流速越大则其混合效果及均匀性越好;水肥流速较低时输水管及输肥管的管径比对水肥混合均匀性的影响较大,两者管径比越小则混合效果越好,随着流速的提高两者管径比对其混合效果的影响逐渐减弱。     

Experimental Investigation on Chip-break Influenced by Cryogenical Cold Air jet

In machine cutting, the replacement of traditionalKGcutting solution with cryogenical cold air jet not only possesses a good cooling and lubricating efficiency, but also can avoid the occurrenceof environmental pollution. In order to clarify the manner and performance of discharged cutting chip under cryogenical cold air jet condition, an experiment was carried out for steel grade 45 in the dry and cryogenical cold air jet cutting comparatively. The effects of cryogenical cold air jet on the breaking of cutting chip are discussed. Experimental results reveal that, in the valid ranges of pressure and temperature, the cryogenical cold air jet can widen the chip broken region effectively. Different insufflating angle of cold air behaves different influence on the chip-break. From the experiment, it has been gained that the optimized jet insufflatingangle, temperature effecting range and pressure working range of cold air, which provides the foundation of industrial manufacturing.     

LABORATORY INVESTIGATION OF ESSENTIAL CHARACTERISTICS PARAMETERS FOR THE INDUCED-NOZZLE DEVICE

The standoff of a submerged jet is smaller than a non-submerged jet in general. In order to increase the standoff of a submerged jet, the induced-nozzle device is presented with its inducing mechanism analysed in this paper. Under the various inducing medium, the effect of the ratio d2/d1 upon the device's properties is measured. Some reasonable parameters are given. When d2/d1=2.0, approximate straight region of the curve of the jet center line stagnation pressure varying with the standoff is L/d1= l0~12 for inducing air. The induced-nozzle device is compared with the conventional nozzle for shotting some samples. Several applied possibilities of the device are discussed.     

Deoxidation Efficency Research of Jet Themral Dloxidation

In this papet,a new deoxidationmethod-jet thermal deoxidation of industrialfeedwater was presented,a preliminary theoretical anlysis of mechamism of deoxidation methed wasmade. Using this experimental method,we studied the deoxidation methed and checked the effect ofthe temperatare pressure fogging state and jet direction on the deoxidation efficiency.