全文获取类型
收费全文 | 191篇 |
免费 | 7篇 |
国内免费 | 9篇 |
专业分类
林业 | 12篇 |
农学 | 35篇 |
基础科学 | 93篇 |
8篇 | |
综合类 | 56篇 |
农作物 | 2篇 |
水产渔业 | 1篇 |
出版年
2024年 | 1篇 |
2023年 | 1篇 |
2022年 | 1篇 |
2019年 | 2篇 |
2017年 | 2篇 |
2016年 | 3篇 |
2015年 | 6篇 |
2014年 | 5篇 |
2013年 | 11篇 |
2012年 | 7篇 |
2011年 | 10篇 |
2010年 | 17篇 |
2009年 | 14篇 |
2008年 | 18篇 |
2007年 | 22篇 |
2006年 | 22篇 |
2005年 | 18篇 |
2004年 | 15篇 |
2003年 | 9篇 |
2002年 | 1篇 |
2001年 | 4篇 |
2000年 | 3篇 |
1998年 | 4篇 |
1997年 | 2篇 |
1995年 | 2篇 |
1994年 | 3篇 |
1993年 | 1篇 |
1992年 | 2篇 |
1989年 | 1篇 |
排序方式: 共有207条查询结果,搜索用时 0 毫秒
1.
水电站预应力闸墩三维有限元分析 总被引:6,自引:0,他引:6
某水电站溢流坝闸墩承受的荷载以及结构较为复杂,工作弧门推力达18009KN。为了准确了解堰体、闸墩、锚块在各典型运行工况下应力情况,采用三维有限元方法,对该水电站溢洪道控制段预应力中墩进行了整体空间应力与变形分析,得到典型工况下结构的整体位移、变形和结构各重要部位的应力分布规律。研究结果表明预应力闸墩具有整体稳定性,在各种荷载组合效应下整个墩体的应力和变形分布满足设计要求,并根据计算成果评价了混凝土结构的预应力效果。 相似文献
2.
3.
4.
5.
为研究软母线刚度对特高压电气设备地震响应的影响,建立考虑刚度的软母线位形函数、最大弧垂及软母线最大应力的计算公式。通过软母线连接的特高压设备振动台模型试验与有限元计算的对比分析,验证了笔者给出的考虑刚度的软母线位形函数、最大弧垂计算公式的正确性。有限元分析结果表明:当软母线的刚度增大时,软母线的垂跨比减少,软母线与特高压设备之间的地震耦合作用增强,增强了软母线对设备的拉伸作用,从而使设备的地震反应随着导线刚度的增加而增加。软母线刚度对频率较高的设备其地震反应的影响要大于对设备频率较低设备地震反应的影响。 相似文献
6.
In order to researchmechanical capability of the reinforced concrete beam with bonding steel plate, adopting separatemethod to establish finite element model of the reinforced concrete beam with bonding steel plate, using FEM to study dynamical characteristics of the model, have got good results which can not be easily got using traditional resolution method, which can give referenceto study dynamical characteristics of the reinforced concrete beam with bonding steel plate. 相似文献
7.
Elastic-plastic analysis of timber frame and its seven strengthened projects are analyzed with the software ANSYS10.0. The numerical calculation and material mechanics calculation for the timber beam are compared to verify the correctness of the finite element model. The paper also analyzes the law of stress and strain of timber beam. In contrast with the yield load and ultimate load of strengthened timber frames, it shows that the lateral resistance of timber frame with corner supports is greatly improved. And a strengthened project for the timber frame is put forward. 相似文献
8.
CAO Xian lei HAO Ji ping CAO Zhi min ZHANG Tian guang ZHANG Yao LI Tian ji 《保鲜与加工》2009,(5):1-8
To analyze mechanical behavior of Q460 high strength single angle steel struts with an eccentric load at one end in transmission towers, experimental analysis and theoretical calculation were carried out to study the overall stability and local buckling of members. Spherical hinge bearing and double knife edge bearing were applied at axial end of specimens. Influence of some factors on bearing capacity of compression members with eccentricities at both ends was analyzed, such as the end supporting conditions and residual stresses. It was shown that whether spherical hinge bearing or double knife edge bearing was used at axial end, the mechanical behavior can be accurately presented and the residual stresses affected the ultimate load carrying capacity by about 5% or less. Compared with different methods, such as experiment method、finite element method, method in the Guide for American Design of Latticed Steel Transmission Structure(ASCE101997)and method in Chinese Technical Regulation of Design for Tower and Pole Structure of Overhead Transmission Line (DL/T51542002), it was found that the calculated strength of high strength steel member by standard calculation method in DL/T51542000 was over conservative. According to the research results, the revised formulas of ASCE were proposed with dividing actual material strength by the resistance coefficient of rR=1.111. Therefore, the experimental results can provide reference for designing high strength Q460 single angle steel members compressed eccentrically at one end. 相似文献
9.
FEM/BEM (Finite Element Method/Boundary Element Method) mode analysis of the noise radiation from motorcycle engine shell is conducted. The natural frequency is compared between FEM/BEM analysis and experimental analysis. The FEM/BEM results are agreed with the experiment results, which proves that the finite element model is correct. The frequency response is analyzed and the structure’s noise radiation is simulated by means of FEM/BEM, in order to predict the noise radiation from the motorcycle engine shell and gain the sound field characteristic outside the structure. The calculation data is compared with the experiment data in different frequency bands. The result shows high accordance, which indicates that this method is effective. 相似文献
10.
The determination of load share between teeth is a complex problem in gear strength calculation. On the basis of contact finite element method this paper considers the production-assembly error as initial gap to get the finite element model which meets load share between teeth in gear meshing. Through calculating and comparing the result with that from ISO formula to get the load share between teeth which meets the requirements in actual usage. 相似文献