土的弹性抗力与墩顶固结结构物的联合计算

将土、基础及上部结构物视为一个整体，在计入土的弹性抗力后对多跨无铰拱和连续刚构的上下部结构进行联合计算，并给出了算例，可供设计参考。     

负刚度的工作原理及应用初探

This paper deals with the vibration isolation principle of a system with a negative stiffness spring and the energy analysis for this system.As an application of the method, an example of vibration systems with equal frequencies is given. It shows that th     

用简易诊断法检查判断液压系统各元件的工作性能

故障的排除首先在于判断，目前基层维修网点大多数没有检测仪器和设备，出了故障乱拆乱卸，导致液压元件工作失灵，甚至整车液压系统瘫痪。拖拉机液压系统产生故障的主要原因是液压元件工作性能恶化引起的。为此，介绍了在没有检测仪器和设备的条件下，如何应用简易诊断法检查判断各液压元件的工作性能。     

手动比例复合阀在中高压液压绞纲机中的应用

中高压液压技术在海洋捕捞机械—绞纲机中的使用推动了我国渔业机械的发展,手动比例复合阀在中高压液压技术上的应用则大大加快了液压绞纲机在国内渔业生产中的普及。目前,我国浙江、江苏、福建、广东和山东等省沿海渔民使用的绞纲机普遍采用带手动比例复合阀的液压系统。为此,对手动比例复合阀换向、溢流、调速集成等功能进行了分析。     

农机液压技术的应用与发展

液压技术的应用已成为现代化农业机械的典型标志。为此,介绍了农机液压技术的应用现状;并根据科学技术的发展,简要分析了农机液压技术的发展趋势。     

一种准零刚度被动隔振系统的非线性共振响应分析

分析了一种机构的负刚度特性和它与线性主弹簧并联后而成的隔振系统的准零刚度特性，推导了准零刚度被动隔振系统的主谐波共振、亚谐波共振和超谐波共振的幅频特性表达式.结果表明，机构的负刚度区域随弹簧的初始变形与杆长的比值增大而变宽；隔振系统的准零刚度区域随主弹簧的刚度与机构中的弹簧总刚度的比值以及机构中的弹簧初始变形与杆长的比值增大而变宽；经比较发现，本文推得的被动隔振系统的同一种谐波共振幅频特性与杜芬方程的幅频特性均存在较大偏差.因此，对于这类被动隔振系统的运动微分方程，若以位移激励的幅值与激励频率平方的乘积代替单位质量的激励力幅值按杜芬方程的解来处理谐波共振问题将会带来较大误差.     

Impact on soil physical properties of using large-grain legumes for catch crop cultivation under different tillage conditions

In Central Europe, various plant species including large-grain legumes and their mixtures are grown as catch crops, particularly between grains harvested early and subsequent summer crops. This article investigates the question of how soil structure in the topsoil is influenced when catch cropping with large-grain legumes (experimental factor A: without catch crop, with catch crop) under different ploughless tillage conditions during catch crop seeding (experimental factor B: deep tillage/25–30 cm, shallow tillage/8–10 cm). Five one-year trials were performed using standard machinery at various sites in Germany. Soil core samples extracted from the topsoil in the spring after catch crop cultivation served to identify air capacity, saturated hydraulic conductivity and precompression stress. The above-ground and below-ground biomass yields of the catch crops were also determined at most of the sites. In addition, the soil compaction risk for the working steps in the experiments was calculated using the REPRO model.The dry matter yield of the catch crops varied considerably between the individual trial sites and years. In particular, high levels of dry matter were able to form in the case of early seeding and a sufficient supply of precipitation. The soil structure was only rarely affected positively by catch crop cultivation, and catch crops did not contribute in the short term to loosening already compacted topsoils. In contrast, mechanical soil stresses caused by driving over the ground and additional working steps used in cultivating catch crops often led to lower air capacity in these treatments. This is consistent with the soil compaction risks calculated using the REPRO model, which were higher in the treatments with catch cropping. Catch crop cultivation also only resulted in improved mechanical stability at one location. The positive effect of deep ploughless tillage on air capacity and saturated hydraulic conductivity, however, became more clearly evident regardless of catch crop cultivation. In order for catch crop cultivation with large-grain legumes to be able to have a favourable impact on soil structure, it is therefore important that cultivating them does not result in any new soil compaction. In the conditions evaluated, deep tillage was more effective at loosening compacted topsoil than growing catch crops.     

支管射流三通结构优化与试验

为了提高支管射流三通水力性能,改善滴灌的灌水均匀性,基于CFX数值模拟技术,对进口宽度为15 mm的支管射流三通进行结构优化.选取位差、劈距、劈尖半径和侧壁倾角为影响因素,通过四因素三水平正交设计了9组模型,边界条件设定为进口压力100 kPa.选取支管射流三通出口设计流量为评价标准,支管射流三通最优结构尺寸为位差5.5 mm、劈距113 mm、劈尖半径13 mm、侧壁倾角10°.此结构尺寸参数下的支管射流三通水力性能试验结果表明:在进口水压为100 kPa时,支管射流三通脉冲频率为148次/min,水头压力振幅为37.9 kPa,水头压力损失为16.7 kPa,出口流量为0.698 L/s;支管射流三通所接滴灌带长度为60 m时,与普通支管三通相比,支管射流三通的灌水均匀系数提高了2.78%,流量偏差率降低了4.72%.该研究可为射流技术在脉冲滴灌系统的研究、开发与应用提供理论依据.     

基于Simulink的液压系统建模与仿真

针对农业机械中液压系统结构复杂、研发周期长等问题,通过分析农业机械中液压回路各个组成元件特性,基于Simulink构建元件动态数学模型。对液压回路进行研究,分析了液压回路在不同元件参数下的动态性能,为优化液压回路系统提供参考。     

某厂区办公楼的结构设计

笔者结合工程实例,采用SATWE软件对单跨框架结构进行计算分析,并浅析了设计中应重点注意的问题。