变截面构件的剪应力计算

变截面构件的弯曲变形是实际构件常见变形之一，现行钢筋混凝土设计规范提供的和实际设计计算应用的剪应力计算公式未考虑截面变化的影响，有较大的误差。本文用材料力学方法推出考虑变截面影响的剪应力计算公式，以便在实际设计计算应用。     

开口薄壁结构弯扭屈曲能量原理的有限变形理论分析

The formulas of the total potential energy of arbitrary thin- walled open cross section member counting in the geometric non-linear factors is deduced. The deductions are based on the most general finite deformation theory and the two assumptions that"the     

多菌灵降解菌的鉴定及降解条件初步优化

对已分离到的多菌灵降解菌进行16S r DNA序列分析后,采用均匀设计法,优化多菌灵降解菌降解条件。用4因素6水平混合均匀设计表,综合考察培养时间、接种量、p H、温度对多菌灵降解菌降解能力的影响。通过二次多项式逐步回归得出最终降解条件为:培养时间6 d、接种量10%、p H 4.0、温度为45℃时,最优目标函数Y(降解率)为68.65%。进一步进行盆栽试验,检测该菌在实际应用中的降解效率为59.54%。     

含MCVaR的投资组合优化统一模型

研究了Duarte提出的投资组合优化统一模型及条件风险价值（CVaR），分析了以CVaR为风险度量的投资组合优化模型的具体形式，建立了统一七种模型的投资组合优化统一模型，并发现统一模型是一个凸二次规划问题.     

The Influences of Surrounding Rock Deformation in Deep Roadway under Different Supporting Structures

随着煤矿开采深度的不断增加，围岩变形特征更加复杂。基于ANSYS数值模拟软件，研究4种不同支护条件下深部巷道围岩的变形情况，研究结果表明：30MPa原岩应力作用下，联合支护产生的水平位移和垂直位移都要比其他支护小，变形影响区域也最小，最为适合围岩地质条件较差的巷道。     

THE REIMPROVEMENT FOR IMPULSE OF G. I. TAYLOR THEORY OF PLASTIC DEFORMATION IN IMPACT OF CYL1NDICAL PROJECTILES

In this paper the reimprovement for G. I. Taylor theory of plastic deformation in impact of cylindical projectiles is done. The impulse in the reimproved theory is G. I. Taylor' s 1/2, and 3/4 of G. I. Taylor' s improved theory. The analytical solution of the reimproved theory shows that it gives better agreement with exprimental results than those of the original Taylor' s theory and, the improved theory.     

Artificial Neural Networks Models for Flow Stress during High Temperature Plastic Deformation of Al-Li Alloy

Using gained experimental data to develop the models of stable flow stresses at high temperature plastic deformation by statistical methods for alloy materials, precision of the models is poor and at the same time the processes of modeling are complicated with great workload. On the basis of the data obtained on Gleeble-1500 Thermal Simulator,the predicting models for the relation between stable flow stress during high temperature plastic deformation and deformation strain, strain rate and temperature for 1420 Al-Li alloy have been developed with BP Artificial Neural Network method. The results show that the model on basis of BPNN is practical and it reflects the real feature of the deforming process. It states that the difference between the real value and the output of the model is in order of 5 percent.     

Experimental Study on the Deformation Characteristics of Fine-Sandstone Under the Loading and Unloading Conditions

The deformation characteristics of the fine-sandstone is studied under the loading and unloading conditions at the three different deformation-rates and the two different stress-levels. The experimental results show that there is really the plastic-loop in the deformation curve for the loading deformation curve is different from the unloading deformation curve. But the plastic-loop is nearly unchangeable since the second circulate loading. The residual-deformation is be almost zero since the second circulate loading, and that the slope of the deformation curve increases as the deformation-rate increases, and that the residual-deformation increases as the stress-levels increases.