装修与电气

本文着重地论述了由装修而引发的电气安全技术问题已到了不容忽视的程度。就此问题作 者提出了自己的观点及解决办法。     

中小型水电站发电机专用断路器的选择

正确设计选择发电机保护断路器直接关系到水电站后期的电气设备合理投资、运行维护及保证水电站长周期安全经济地运行.过去中小型水轮发电机大都选用普通型的油断路器或真空断路器或SF6断路器等,近些年来选用普通真空断路器的越来越多.中小型水电站应根据不同接线方式、不同容量的发电机出口断路方法,选择发电机专用断路器.     

Quantification of reservoir bags as airway pressure-limiting devices in a nonrebreathing system

ObjectiveTo evaluate the influence of reservoir bag types, volumes and previous use on the peak pressures (Pmax) and the times to develop 30 cmH₂O pressure (P30) within a nonrebreathing system with a closed adjustable pressure-limiting (APL) valve.Study designIn vitro study using three-way factorial design with repeated measure on one factor.SubjectsA total of 75 new anesthesia reservoir bags (five types, three volumes, five bags from each type × volume). The bag types were reusable latex (RL), disposable latex (DL) and three disposable neoprene (DN-1, DN-2 and DN-3).MethodsEach bag was tested three times (treatments): new, after prestretching and 1 week later. The bags were attached to a Bain system and anesthesia machine with closed APL valve and patient port with O₂ flow 2 L minute^–1 until Pmax was reached. The Pmax and time to reach P30 values were determined from recorded pressure traces. General linear mixed model analysis was used to examine the effects of bag type, volume and treatment. One-sided 95% upper prediction limits of Pmax were calculated to test the null hypothesis that predicted Pmax of new bags would be ≥ 50 cmH₂O for each factor combination.ResultsRL bags were the least and DN-3 bags were the most compliant. Prestretching increased compliance in all bag types. Smaller bags of RL, DL and DN-1 were less compliant than larger ones. The predicted Pmax values were < 50 cmH₂O only for DN-3 bags after prestretching. The time to reach P30 was critically low when using 0.5 L bags (median 17 seconds).Conclusions and clinical relevanceTo minimize the risk of barotrauma, highly compliant reservoir bags (e.g. DN-3) are recommended and reusable bags should be avoided. Bags should be prestretched before first use, 0.5 L bags should be avoided and fresh gas flow minimized.     

泵站继电保护设计方法

分析了进口、国产继电保护设备的不同，提出了对泵站继电保护二次回路的设计新方法。泵站二次设计可按照“单元”设置的原则，将泵站二次设计划分为10／6kV泵站进线、主机、站变、所变、联络等主要单元。     

CMOS集成块在水电站控制电路中的应用

在水电站控制电路中,为完成全站逻辑选控开停机,逻辑选控同期合油开关、跳油开关的功能,用CMOS集成电路替代分立元件,从而提高了水电站的自动化程度,缩小了集控台体积,也有利于安装、调试和维修。     

农用运输车部分电路的改进设计

针对农用运输车的现状、发展前景进行了简要地分析,为了保证行车安全,在转向时加装了前侧灯照明装置、倒车及转向时加装了音乐报警装置;为了保证车辆的安全运行,在气压制动系统中增加安全保护开关,控制发动机的点火电路(汽油机)或熄火电磁阀电路(柴油机),可实现低气压时的自动保护,以保证车辆正常行驶。     

电磁驱动泵设计原理

揭示了一种通过电磁线圈对柱塞产生电磁感应并使之作往复运动的电磁泵的原理。作往复运动的柱塞使得电磁线圈形成了一个封闭的电磁回路。     

双板差分冲量式谷物流量传感器设

设计了一种双板冲量式谷物流量传感器及其差分消振电路,以消除车身振动对测产精度的影响.振动试验表明,在没有谷物输入时联合收获机车身振动导致前后2个检测板产生的2个振动信号是一对共模信号,可通过电路差分的方法消除;差分后传感器的输出电压的信噪比由2.5dB提高到62dB.在零喂入量情况下,振动产生的零点误差小于0.01g/s;在联合收获机正常作业的喂入量范围内(0.5～2kg/s),实验室测量误差小于3%.田间实际测量误差不大于5%.     

激光控制平地系统激光接收器设计与试

激光接收器是激光控制平地系统的关键部分.为了更有效地检测激光信号,扩大接收范围,增加接收距离,提高稳定性和抗干扰性,设计了一种基于集成IC的新型激光接收器.其原理是以红色有机玻璃作为透光窗口,并采用干涉型滤光片来滤除背景光;以硅光电池作为光电探测器,将激光信号转换为电信号;然后采用集成运算放大器设计低噪声前置放大器和主放大器对微弱电信号进行放大;最后,脉冲整形和展宽电路实现脉冲信号到TTL数字信号的转换,以方便后续电路的处理.田间试验结果表明,激光接收器在150m范围内可实现360°全方位稳定工作,垂直工作范围为28.4cm左右,将其用于平地作业时农田的平整误差小于2cm.     

PASSAT领驭2.0自动变速箱偶尔出现紧急运行状况检修分析

结合PASSAT领驭2.0轿车偶尔出现自动变速箱Ⅲ挡运行的紧急运行状况故障,分析了故障码、有关传感器电路,以及故障产生的原因,据此找出了故障点,并排除了故障。