延迟收获对长江中游春玉米农艺性状及机收质量的影响

为探明长江中游玉米籽粒机械直收适宜品种与配套农艺措施，2018—2019年选用不同玉米品种，测定不同机收时间下玉米关键农艺性状、产量及机收质量指标。结果表明，收获时间对春玉米机收产量与机收质量均有显著影响。延迟1周收获后籽粒容重显著增加，机收产量显著提高，2年平均提高9.72%；而延迟2周收获则有降低机收产量的趋势。2年收获时杂质率总体≤3%，而机收籽粒破碎率与损失率均>5%，是该区域春玉米籽粒机收面临的主要问题。籽粒厚度、籽粒含水率和百粒重是影响机收籽粒破碎率的关键性状，三者与机收籽粒破碎率均呈显著的倒二次曲线关系；玉米的倒伏率、穗位高和重心高度是影响机收损失率的关键性状，倒伏率与机收损失率呈显著正相关，而穗位高和重心高度与机收损失率均呈显著的二次曲线关系。延迟收获能显著降低籽粒含水量，从而降低籽粒破碎率，但继续延迟收获有增加倒伏的风险。综上，长江中游春玉米成熟后适时延迟7~10 d收获，可有效降低籽粒含水量与机收籽粒破碎率，提高玉米籽粒机收产量。     

不同秧龄对沿江地区双季晚稻秧苗素质及产量的影响

以早熟高产品种上农粳2号和镇稻18为材料,采用常规毯苗机械栽插,分别设置20 d、24 d、28 d、32 d等4个秧龄处理,研究不同秧龄对沿江地区双季晚稻秧苗素质、生育进程、茎蘖动态及产量构成的影响。结果表明,随秧龄天数增加,参试品种的绿叶数、茎基宽和根系盘结力均逐渐升高;与20 d、24 d和28 d秧龄的处理相比,32 d秧龄处理的成熟期提前4~5 d,茎蘖高峰期提早15 d左右,结实率显著升高;与24 d秧龄处理相比,上农粳2号和镇稻18在32 d秧龄处理下的产量分别提高10.26%和20.82%。在秧苗强化化控和苗床管理的条件下,安徽沿江地区常规毯苗机插的栽插秧龄可延长至32 d。     

有初始缺陷板件超屈曲强度的半分析法研究

本文应用大挠度理论分析了初始缺陷对板件超屈曲强度的影响,并为板件后屈曲分析提出了一个样条函数半分析计算法.该法对各种载荷及位移边界条件板件均可进行计算,与有限元法等相比较,具有计算量少,精度高等显著特点.数值计算结果为冷弯型钢结构设计提供了较完善的理论依据.     

烘丝温度和时间对生丝机械性能的影响

从刚落下的丝片上摇取小绞丝,分别在25—180℃和30、60、90min下进行干热处理后,测定其机械性能。结果表明:在90—100℃、30—60分钟时,生丝的强伸力、初始模量以及抱合等机械性能都较好,烘丝温度太高,时间太长都会对生丝机械性能产生不良的影响。     

赤霉素及机械处理的相互作用对破除Sandersonia aurantiaca种子休眠的研究

在预备试验的基础上，选用了21种促进种子发芽的方法，结果显示，完整的s．aurantiaca种子对任何处理都无响应，砂纸磨擦 近胚根处切除小部分可使种子发芽率提高至11％。以上处理结合300mg／L GA3溶液的使用可破除种子休眠，使种子发芽率提高到69％以上。结果还表明，S．aurantiaca种子发芽的适宜温度为20℃；25℃ 16h／d光照及30℃的条件可降低种子的发芽率。研究还对S．aurantiaca种子的吸胀能力以及所含抑制物对生菜种子发芽的影响进行了比较。初步得出，S．aurantiaca种子具有种皮限制和种胚休眠的双重休眠机制，GA3和机械处理的相互作用可破除种子休眠。     

甲醛捕捉剂在胶合板生产中的应用

普通UF树脂胶中添加甲醛捕捉剂H300或H800后,其固化时间明显延长.采用H300或H800改性的UF醛树脂胶黏剂生产胶合板,在保证胶合强度的前提下,板材的甲醛释放量达到国标E2或E1级要求.     

改善E1级胶合板用UF胶粘剂预压性能的研究

利用氧化淀粉在树脂合成后期、API在调胶时加入分别对脲醛树脂进行改性，探讨改性UF对胶合板预压强度的影响。采用正交实验法对比改性后胶合板的预压性能和改性后胶合板的甲醛释放量的变化。结果表明：随着API量的加大，胶合板的预压性能得以提高；而氧化淀粉改性后则随着量的加大，一定范围内胶合板的预压性能得以提高，加入量继续加大后反而下降。     

Influence of death struggle on the structural changes in chub mackerel muscle during chilled storage

ABSTRACT: Chub mackerel (34–35 cm, approximately 500 g), which were caught by fishing with a rod and line at the Bungo Channel, Oita prefecture, were rested overnight in a fish preserve and either killed by decapitation (control group) or allowed to struggle in air for 30 min (struggled group). Muscle samples were excised every 4 h, and measurements on breaking strength and histological observations were done for both groups. The breaking strength of muscle in the control group was significantly higher than that in the struggled group, whereby a decrease in breaking strength was delayed for 12 h compared to the struggled group. Light microscopy showed space extension among muscle cells in association with a decrease in breaking strength. Especially in the struggled group, the extended area was larger and the difference in area was significant at the time when breaking strength showed a significant difference. Using electron microscopy, the extended area showed cut and/or disappeared collagen fibrils. From these results, it was demonstrated that struggling to death promoted the degradation of collagen fibrils and the weakening of connective tissue and, resultantly, led to the faster softening of muscle of chub mackerel.     

Application of acoustic Doppler current profiler combined with a scientific echo sounder for krill Euphausia pacifica density estimation

ABSTRACT:   An application of the acoustic Doppler current profiler (ADCP, 153.6 kHz) in combination with a scientific echo sounder (EK60, 38 and 200 kHz) was investigated to estimate the density of krill Euphausia pacifica . The acoustic backscattering strength from sound scattering layers was compared with biomass estimates from midwater trawls. Euphausia pacifica was targeted among mixed species populations in the sound scattering layer in the offshore Funka Bay area of Hokkaido, Japan. The frequency characteristics of acoustic backscattering by krill were calculated using a distorted wave Born approximation scattering model at three frequencies. Krill aggregations identified from the EK60 data were extracted as the mean volume backscattering strength difference between two frequencies. They were then used to identify similar aggregations in the ADCP data by matching observation times and depths for the two methods, which were applied simultaneously. Results from the comparison of the mean volume backscattering strength and the density calculated from the ADCP and EK60 showed that ADCP can be used to measure density and spatial–temporal distribution of krill aggregations. Current speed and direction at the study site were found to be 16.1 cm/s and 187.0°, respectively, and krill speed and direction (including the current component) were found to be 19.8 cm/s and 172.2°, respectively. Based on the ADCP data, the net speed and direction of the krill aggregations were found to be 5.9 cm/s and 128.0°, respectively.     

Evaluation of Five Most Commonly Grown Cotton Cultivars (Gossypium hirsutum L.) Under Mediterranean Conditions: Productivity and Fibre Quality

Studies were conducted in four regions of central Greece (Larisa, Karditsa, Livadia, Thiva), to evaluate the productivity and fibre properties (fibre strength and fibre length) of the five most commonly grown cotton cultivars in these regions. The experiments lasted for 6 years (1995–2000). All the characteristics tested were strongly influenced by the factors ‘year’, ‘cultivar’ and ‘region’. Significant cultivar × region, year × cultivar, region × year and cultivar × region × year interactions occurred for all the characteristics studied. The cultivar Alegria had the highest seed‐cotton and lint yield, while Aria had the lowest ones. Both cultivars gave the highest mean lint percentage but the lowest mean boll weight (MBW). Alegria had the lowest fibre strength, while Aria had the highest. The Acala‐type cultivars, Acala SJ2 and Zeta 2, had intermediate seed‐cotton and lint yield, while Vered 171 had high seed‐cotton and satisfactory lint yield. The three cultivars mentioned above had the highest MBW and very good fibre strength. Positive correlation was observed between fibre strength and length. In spite of the fact that mean fibre length was statistically the same in all cultivars, it was influenced by the factor ‘year’, as a result of different weather conditions. The year 1996 was the most unfavourable one for seed‐cotton yield and MBW, because it was characterized by lower than average air temperatures and rather dry conditions for all study sites. The factor ‘region’, a combination of different climatic conditions and cultural practices, influenced significantly all the parameters studied.