温室分层土壤条件下滴头流量和间距对湿润体的影响

基于温室田间土壤大多容重分层和不均匀的特点,进行了原状分层、分层筛分均质和筛分均质3种土壤对湿润体影响的对比研究。试验地土壤为粉土(中国制分类),原状分层和分层筛分均质土壤0~20 cm容重为1.44 g/cm3,20~40 cm为1.63 g/cm3,40~60 cm为1.55 g/cm3,筛分均质土壤采用0~60 cm平均容重1.54 g/cm3。滴头流量设2.7 L/h和1.4 L/h二种,滴头间距有30,50,70,100 cm四种,采用剖面法观测土壤含水率和湿润体发展。试验结果表明:①湿润体在现场原状分层土壤、分层均质和均质土壤中有很大的区别,分层筛分均质和筛分均质土壤中均为碗状原状,而分层土壤的湿润体形状在灌水量较小时为碗状,随灌水时间的延长,其形状逐渐变为椭柱体;②土壤容重分层情况对湿润锋的运移影响很大,分层土壤由于20~40 cm容重较大纵向湿润锋发展缓慢,灌水历时8 h时最大纵向湿润锋分别为27 cm和25 cm,且原状分层土壤灌水量较大时出现0 cm深度处横向湿润锋小于-7~-13 cm深度处湿润锋现象;而筛分均质土壤中纵向湿润锋明显大于分层土壤,灌水历时8 h时最大纵向湿润锋为32 cm;③原状分层土壤湿润体内平均含水率高于分层筛分均质和筛分均质土壤,但各组均高于田持,土壤含水率均匀度均在82%以上。基于这种结果,建议设计湿润比应根据温室土壤特点和设计灌水量进行现场测试确定,这样更符合实际情况。     

重力式计量包装机的设计与研究

介绍了定量包装机的结构、气缸选型以及料仓容积等参数的计算。该机配以PLC气动控制装置、嵌入式电脑核心的包装机控制仪,具有高精度、高速度及长期工作可靠性好等特点。它可以和自动取袋、封口机配合使用,根据不同物料的料性及工艺要求,进行自动称重包装,从而满足了国内粮食及其初深加工产品计量包装的性能指标要求,并广泛应用于粮食、化工等行业。     

湘西桤木人工林蓄积量模型及适宜经营密度研究

密度是表达林分结构的重要指标,立地条件、树种及林龄不同时,其林分最佳密度也不相同。笔者以湘西桤木人工林为研究对象,采用数量化方法I和非线性回归分析方法,对2009年和2010年调查的78块标准地数据进行数据分析处理与建模。结果表明：（1）平均高、公顷株数、土层厚度、龄组、坡向、坡位、自然灾害、海拔、树种组成8种因子中,平均高、公顷株数、土层厚度和龄组对湘西桤木人工林平均木材积和单位面积蓄积量均有显著性影响,而海拔和树种组成对湘西桤木人工林平均木材积和单位面积蓄积量均无显著性影响。这对建立桤木人工林蓄积量与密度、平均高收集数据时提供理论指导,同时既能节省外业调查费用,又能保证建模数据的科学性。（2）建立了湘西8~10年桤木人工林蓄积量与密度、平均高相关关系模型： ,建模精度为96.8458%,平均相对误差为1.1334%。模型适应性检验表明,残差值呈对称均匀分布,其平均相对误差为-1.2156%。（3）该地区8~10年桤木人林的最佳经营密度为800~1000株/hm2。这对于合理地经营和管理湘西桤木人工林具有重要的理论和实际指导意义。     

耕作土壤表面不平度分析

利用激光式不平度测试仪测定犁耕耕地地面、圆盘耙耙地地面和驱动耙耙地地面的不平度，测定地面不平度沿着3个方向进行，即平行、倾斜和垂直于耕作方向。对每一种地面不平度的RMS高度、自相关长度和自相关函数进行了分析，结果表明：对于短的地块，可用单一尺度来表征地表不平度的特征，地表不平度特征属于指数相关函数，RMS高度和自相关长度具有明显的相关性；对于长的地块，平整的农业地表不平度具有分形性或多尺度性，其自相关函数是一种分形过程。     

The genetic relationship between popping expansion volume and two yield components in popcorn using unconditional and conditional QTL analysis

Popping expansion volume (PEV) is the most important quality trait in popcorn, while its germplasm is inferior to normal dent/flint corn in yield. In this study, 259 F_2:3 families, developed from the cross between a dent corn inbred Dan232 and a popcorn inbred N04, were evaluated for their PEV, grain weight per plant (GWP) and 100-grain weight (100 GW) in two environments. The genetic relationship between PEV and GWP, and 100 GW on individual gene loci were evaluated using unconditional and conditional QTL mapping methods. In total, five, one and three unconditional QTL were identified for PEV, GWP, and 100 GW, respectively. The positive alleles of all QTL for PEV were from N04, while positive alleles of all QTL for GWP and 100 GW were from Dan232. In conditional mapping, one and two QTL failed to be detected, and all four additional QTL were detected. Nevertheless, three QTL were identified, which controlled PEV independently from GWP/100 GW. They seemed to be potential candidates in popcorn breeding to increase PEV without decreasing GWP/100 GW. The results suggested that for significantly correlated traits, the conditional QTL mapping method could be used to dissect the genetic interrelationship between traits at the level of individual QTL, as well as reveal additional QTL that were undetectable by unconditional mapping.     

基于地相位优化估计的RVoG三阶段森林冠层高度反演

极化干涉合成孔径雷达（PolInSAR）估测森林结构参数中,数据受基线长度、信噪比、环境地形以及雷达波长的影响,尤其在复杂森林环境条件下,会导致观测到的复相干存在误差,从而影响最终的反演结果。为解决此问题,首先探讨了体相干选择对RVoG三阶段森林冠层高度反演的影响,以地相位为参考逐像素选择距离地相位最远的相干性作为体相干。其次改进了地相位估计方法,采用戴明回归（DMR）和正交回归（OGR）2种相干直线拟合方法来改进地相位的估计,并在DMR拟合方法中设置了不同的误差比（0.3和0.6）来比较地相位估计方法对RVoG三阶段森林冠层高度反演的影响。研究结果表明：以地相位为参考逐像素选择体相干的反演结果相较于直接使用HV极化通道的复相干γ_HV为体相干的反演精度有明显提升,决定系数（R²）由0.349增加到0.383,均方误差由7.097 m²降低到5.755 m²。在体相干优化选择的基础上,采用了戴明回归和正交回归对地相位估计方法进行了改进。表明基于最小二乘回归（LSR）地相位估计的RVoG三阶段反演精度最...     

脉冲式烟雾水雾机热力雾化水剂农药效果分析

针对脉冲式烟雾水雾机在喷施水雾剂农药时常出现滴液、流液或较大雾滴群等雾化不良现象,通过改装6HYW-60S型脉冲式烟雾水雾机,将药液流量设置成可调的测试装置,设定5个油门开度及4个药液流量,测试了脉冲发动机喷药前后的气流速度、温度及各喷药工况下的雾滴粒径分布。结果表明,在最小的油门启动开度到最大的油门工作开度可调范围内,对应的脉冲发动机燃油消耗率变化范围较小（相对变化13.0%）,喷管内对应的气流温度与速度也发生同等程度的变化。喷药时,喷管口处的气流温度与速度发生明显变化,由不喷药时约700℃的高温气流下降为75℃左右的雾滴流,相应的气流速度下降了16%左右;油门开度及药液流量对雾滴流温度的影响非常小,但对雾滴流速度的影响非常明显,油门开度增大,雾滴流速度明显增加,药液流量增大,雾滴流速度明显下降。在各油门开度下,对最小药液流量20L/h的雾化效果均不佳,尤其距喷雾出口较近处存在大量的300μm以上的较大雾滴,这些大雾滴极易跌落至地面,无法有效喷施到目标物上;药液流量增大至40L/h及以上时,各油门开度下的雾滴体积中径均较小,同一工况下各位置点的平均值不超过60μm。热力雾化的雾滴粒径分布曲线不是单一峰值的正态分布形态,常会出现不同中心雾滴粒径的雾滴群,且这些雾滴群的中心雾滴粒径基本保持一致。从喷雾出口喷出的雾滴流中,喷管中心轴线上的雾滴细小均匀、雾化充分,中心轴线上方的雾滴一般比中心点处稍大,中心轴线下方雾滴明显增大,且距中心轴线越远的下方,雾滴增大越明显,即雾滴流中较大雾滴群的量逐渐增加。以药液流量60L/h及油门开度90°为最佳雾化工况,在整个喷施区域内均形成了良好的雾化效果。     

喷水推进器全流道空化流动数值模拟

为了研究对旋轴流式喷水推进器内部空化特性,基于ANSYS-CFX软件,利用SST k-ω湍流模型和Zwart空化模型,对不同转速以及设计航速条件下喷水推进器进行全流域空化数值计算,得到了喷水推进器两级叶轮叶片以及叶轮流道内空泡体积分数分布情况.结果表明:在喷水推进器首级叶轮吸力面轮缘处最先发生空化,随着转速的增加,空泡不断地向叶轮轮毂处蔓延,并且体积分数逐渐增加;由于非均匀进流的影响,次级叶轮吸力面进口至出口中部低压区开始出现空泡;且受流动传递性的影响,次级叶轮处在靠近水平面下半叶轮通道内的叶片空化更为严重;在不同的NPSHr下,由于首级叶轮的预压,次级叶轮压力面一直没有空泡附着,表明对旋轴流式喷水推进器具有良好的抗空化性能.     

Simulation of transpiration, drainage, N uptake, nitrate leaching, and N uptake concentration in tomato grown in open substrate

Free-drainage or “open” substrate system used for vegetable production in greenhouses is associated with appreciable NO₃⁻ leaching losses and drainage volumes. Simulation models of crop N uptake, N leaching, water use and drainage of crops in these systems will be useful for crop and water resource management, and environmental assessment. This work (i) modified the TOMGRO model to simulate N uptake for tomato grown in greenhouses in SE Spain, (ii) modified the PrHo model to simulate transpiration of tomato grown in substrate and (iii) developed an aggregated model combining TOMGRO and PrHo to calculate N uptake concentrations and drainage NO₃⁻ concentration. The component models simulate NO₃⁻-N leached by subtracting simulated N uptake from measured applied N, and drainage by subtracting simulated transpiration from measured irrigation. Three tomato crops grown sequentially in free-draining rock wool in a plastic greenhouse were used for calibration and validation. Measured daily transpiration was determined by the water balance method from daily measurements of irrigation and drainage. Measured N uptake was determined by N balance, using data of volumes and of concentrations of NO₃⁻ and NH₄⁺ in applied nutrient solution and drainage. Accuracy of the two modified component models and aggregated model was assessed by comparing simulated to measured values using linear regression analysis, comparison of slope and intercept values of regression equations, and root mean squared error (RMSE) values. For the three crops, the modified TOMGRO provided accurate simulations of cumulative crop N uptake, (RMSE = 6.4, 1.9 and 2.6% of total N uptake) and NO₃⁻-N leached (RMSE = 11.0, 10.3, and 6.1% of total NO₃⁻-N leached). The modified PrHo provided accurate simulation of cumulative transpiration (RMSE = 4.3, 1.7 and 2.4% of total transpiration) and cumulative drainage (RMSE = 13.8, 6.9, 7.4% of total drainage). For the four cumulative parameters, slopes and intercepts of the linear regressions were mostly not statistically significant (P < 0.05) from one and zero, respectively, and coefficient of determination (r²) values were 0.96-0.98. Simulated values of total drainage volumes for the three crops were +21, +1 and −13% of measured total drainage volumes. The aggregated TOMGRO-PrHo model generally provided accurate simulation of crop N uptake concentration after 30-40 days of transplanting, with an average RMSE of approximately 2 mmol L⁻¹. Simulated values of average NO₃⁻ concentration in drainage, obtained with the aggregated model, were −7, +18 and +31% of measured values.     

Differences in swimbladder volume between Baltic and Norwegian spring-spawning herring: Consequences for mean target strength

Fish swimbladders, where present, contribute most to the scattering of sound by fish, as measured by the target strength (TS). The volumes of the swimbladders of two different European stocks of Atlantic herring were compared to consider the effect on estimates of TS. Swimbladder volumes of Baltic and Norwegian spring-spawning herring (Clupea harengus) were measured, together with individual herring fat content. Swimbladder volumes were found to differ significantly between the two herring stocks. Baltic herring have a larger swimbladder volume, which is suggested to be associated with the fish's low fat content, which in turn may be linked to its specific energy budget and the low salinity of the Baltic Sea. A buoyancy model that considered the different salinity conditions and fat proportions was used to evaluate the observed differences in swimbladder volume. The swimbladder volume data were subsequently used to model the mean target strength as a function of depth and growth pattern. Backscattering of the swimbladder was modelled using the modal-series-based deformed-cylinder model (MSB-DCM), describing the swimbladder as a gas-filled, elongated prolate spheroid. The fish body component was modelled as a fluid-filled ellipsoid using the distorted wave Born approximation (DWBA). Modelling results support a different TS-to-size relationship for Baltic herring, with a stronger echo, due to the larger swimbladder. Depth- and length-dependent TS relationships based on the model results are suggested.