CMC粘接法制备柱状成型活性炭

以羧甲基纤维素钠(CMC)为粘接剂制备了柱状成型活性炭,研究了炭化温度、CMC添加量对产物吸附性能、孔结构及强度的影响。结果表明,随着炭化温度的升高,柱状成型活性炭的比表面积、亚甲基蓝吸附值和碘吸附值均呈现下降趋势;随着CMC添加量的增加,柱状成型活性炭的比表面积、总孔容、微孔容、平均孔径及亚甲基蓝吸附值、碘吸附值及对甲苯的吸附能力均逐渐降低,其强度逐渐增大。CMC粘接法制备柱状成型活性炭的最佳工艺为炭化温度200℃,CMC添加量10%,产物比表面积可达844.9 m2/g,亚甲基蓝吸附值和碘吸附值分别为189.2及968.2 mg/g,强度可达99.83%,甲苯的吸附率达65.5%。     

The impact of cellulose fibre surface modification on some physico-chemical properties of the ensuing papers

This review covers both physical and chemical modifications of cellulose fibre surface and their impact on the properties of the ensuing papers. It is not restricted to actual industrial operations, but also deals instead with ongoing research in this area, which appears promising in terms of possible applications to papermaking.     

Phosphorus desorption affected by drying and wetting cycles in Ferralsols and Luvisols of Brazilian Northeast

Semiarid soils are subjected to wetting and drying cycles which influence sorption and desorption of applied phosphorus fertilizer. Phosphorus desorption was determined in soils from toposequences of two soil groups (Ferralsol and Luvisol) from a semiarid area, subjected to wetting and drying cycles. Samples from surface and subsurface horizons of upslope, midslope, and downslope positions were incubated for 4 months with phosphorus doses corresponding to 0, 5, 10, 25, 50, 75, and 100% of the maximum adsorption capacity, under constant moisture (80% water retention capacity) or 12 cycles of wetting and drying. Phosphorus desorption was lower in the Ferralsol than in the Luvisol, and lower in the subsurface than in the surface horizons, probably due to greater clay, Fe, and Al oxides contents, but they were similar among slope positions, of same mineralogy. Desorption tended to be greater in samples submitted to wetting and drying cycles but differences were small. P recovery reached 40–50% in the Luvisol, and 30–40% in the Ferralsol. The relatively low P retention capacity suggests a high residual effect of the P applied. Therefore, in relation to P losses, water retention techniques are less important than those that prevent soil erosion.     

Effect of a gibberellin-biosynthesis inhibitor treatment on the physicochemical properties of sorghum starch

Inhibition of plant growth by Trinexapac-ethyl, TE, a gibberellin-biosynthesis inhibitor, can produce a shorter stemmed plant, requiring less nutrients and water to grow, while maintaining grain yield. Although TE and other plant growth regulators are commonly used in grain crops, their effects on starch biosynthesis in the grains have not been systematically examined. The changes in the structural and functional properties of starch in grains harvested from TE-treated sorghum (Sorghum bicolor (L.) Moench) were examined, and the results compared with those from the untreated controls. TE treatment had little or no effects on the molecular structures of starch, starch granule morphology, and starch and amylose contents, but increased the protein content of the grains significantly. Consistent with the lack of change in the molecular structure, there were no significant effects on the thermal properties of the starch. The pasting properties of TE-treated sorghum flours, however, showed lower peak viscosity, trough, and final viscosity, which were attributed to their higher protein contents. The TE treatment thus does not have an appreciable effect on the biosynthesis of starch during grain development in sorghum.     

Physicochemical Characteristics of Biochars Derived From Corn,Hardwood, Miscanthus,and Horse Manure Biomasses

Biochar, a carbon-rich by-product of biomass pyrolysis, is widely recognized as a potential ingredient for soil amendment, fertility, and carbon sequestration owing to its favorable physicochemical properties. The objective of this study was to investigate the chemical and physical properties of biochars produced through pyrolysis at 450°C from agricultural residues available in Northwest Missouri, namely hardwood (HW), corn stover (CR), miscanthus (MS), and horse manure (HM). These properties were assessed through the analysis of pyrolysis yield, pH, volatile matter, fixed carbon, ash and carbon (C), hydrogen (H), sulfur (S), nitrogen (N) contents, trace metal concentrations, surface morphology, surface functional groups, bulk density, and water holding capacity. The biochars derived from HW, MS and CR materials showed high volatile-matter (33–42%), high fixed carbon contents (42–47%), very low ash contents (6–15%), and low bulk density (0.14–0.28 g cm^?3) as compared to that of HM. A wide range of trace elements was observed in biochar samples with significant differences in concentrations. In addition, CR, HW and MS biochars displayed a disordered graphitic-like structure with well-developed pores and surface areas of 23, 70 and 90 m²/g respectively, and high water-holding capacity up to 750%, indicating their potential application as a soil amendment.