有机修饰改性对旱地土壤吸附镉离子特性的影响

研究了以不同比例十六烷基三甲基溴化铵(CTMAB)单一修饰和十六烷基三甲基溴化铵 十二烷基磺酸钠(CTMAB SDS)混合修饰土娄土耕层对重金属镉离子吸附的影响,结果表明:吸附量顺序为耕层原土>50%CTMAB>100%CTMAB 20%SDS>100%CTMAB,温度升高,吸附量上升;最佳吸附等温线模型可以用BET模型描述,热力学参数的研究表明,吸附自发性与吸附量具有相同的变化规律,反应的焓变与熵变共同决定了反应的自发性。从热力学角度对修饰改性土娄土对Cd2 吸附的机理进行了探讨。     

仿生鱿鱼肉鳍扑动推进机理数值研究

在仿生机器鱿鱼的设计制作中,通过肉鳍摆动辅助腕的收缩以及喷水推进的组合,使得鱿鱼可以以多种运动形式进行游泳。为研究鱿鱼肉鳍的扑动推进机理,采用计算流体力学(CFD)方法对生物鱿鱼外形进行等比例数值建模,计算分析鱿鱼肉鳍在不同扑动角度下的水动力特性。在此基础上,通过改变肉鳍占体比例、肉鳍形状等参数,研究不同参数对鱿鱼肉鳍扑动推进性能的影响。结果显示:鱿鱼肉鳍扑动过程中肉鳍上下表面出现明显涡流区与压力差,鱿鱼在该压力差的作用下完成升沉运动与水平运动;当鱿鱼肉鳍占体比例超过0.3时,升沉力与水平推进力均随肉鳍占体比例的增加呈明显上升趋势,而阻力变化趋于稳定,适当增加肉鳍的占体比例可获得更高的扑动推进效率;横菱形肉鳍具有较高的推进效率与较低的游动阻力,在仿生鱿鱼设计中是一种较为理想的选择。研究结果为仿生机器鱿鱼的设计制作提供了计算方法和理论参考。     

蛋氨酸硒对牛营养物质代谢和生化指标的影响

选用16头体重420kg、年龄2.5岁西门塔尔牛阉牛,采用随机区组设计分为4组,以蛋氨酸硒为硒源,在基础日粮中分别添加硒0、0.3、0.6和0.9mg/kg,研究蛋氨酸硒对西门塔尔牛营养物质消化代谢和理化指标的影响。结果表明,0.3和0.6mg/kg组日粮的有机物质、粗蛋白质、粗脂肪、中性洗涤纤维、酸性洗涤纤维消化率显著高于对照(P<0.05);0.6和0.9mg/kg组的消化氮、沉积氮和氮利用率显著高于对照(P<0.05);0.6mg/kg组的硒、钙、磷、锰、铜、钼的存留率显著提高(P<0.05),锌和硫的存留率无显著差异;0.6mg/kg组的血清甘油三酯、血糖、白蛋白、总蛋白、GPT、GOT、GSH-px和GSH均显著高于对照(P<0.05)。0.6和0.9mg/kg组丙二醛含量显著低于对照(P<0.05);0.6mg/kg组血清硒含量显著高于对照(P<0.05)。日粮加硒0.6mg/kg显著改善日粮营养物质消化代谢,提高了机体抗氧化能力,建议以蛋氨酸硒为硒源时日粮加硒0.60mg/kg。     

基于离散元仿真参数的微型薯物料测定

以脱毒微型马铃薯(简称"微型薯")"大西洋""中薯5号"和"华薯1号"为研究对象,以离散元软件EDEM中微型薯仿真研究所需的相关参数为目标,测定3种微型薯的物理力学特征参数和接触力学参数。采用响应曲面法设计试验,以静摩擦系数、滚动摩擦系数为试验变量,以堆积角为试验指标,将上述测定后的参数输入EDEM进行仿真,求取微型薯之间的滚动摩擦系数。以堆积角为响应值,使用圆筒提升法验证仿真结果的可信度。结果表明:与试验实际堆积角相比,不同品种的微型薯仿真结果差异均低于3%,仿真结果可靠。     

东海原甲藻和中肋骨条藻适宜生长条件及叶绿素荧光特性的对比

为探究东海原甲藻（Prorocentrum donghaiense）和中肋骨条藻（Skeletonema costatum）两种赤潮高发藻适宜生长条件及叶绿素荧光参数的差异,选取温度（17、20、23、26 ℃）、光照[40、80、120、160 μmol photons /（m²·s）]、磷酸盐（0.1、1.0、5.0、10.0 μmol/L）、初始生物量（1×10⁴、3×10⁴、5×10⁴、7×10⁴ cells/mL）等4个因素4水平试验进行室内培养实验。结果表明,对两种微藻叶绿素a峰值质量浓度产生极其显著影响的是磷酸盐（P<0.01）,光照、温度、初始生物量未产生显著影响。磷酸盐添加表明,在0.1、1.0 μmol/L低磷环境中,东海原甲藻生物量及稳定性高于中肋骨条藻,高初始生物量消耗磷酸盐后东海原甲藻能够继续生存,中肋骨条藻则细胞丰度持续衰落;在5.0和10.0 μmol/L高磷环境中,中肋骨条藻较东海原甲藻增殖最快,生物量更高。东海原甲藻的荧光参数F_v/F_m、α较中肋骨条藻稳定,表明其光合活性稳定;更小的细胞体积和更大的比表面积使中肋骨条藻于培养初期快速达到峰值,表明其对磷酸盐利用能力强。10.0 μmol/L磷酸盐浓度组,4个荧光参数最大,光合活性最强,更容易发生赤潮。东海原甲藻的光合活性主要受光照的影响,中肋骨条藻的光合活性更大程度受磷酸盐、光照的影响。     

超声提取-气相色谱法测定土壤1,9-癸二醇

1,9-癸二醇是由水稻根系分泌物中发现的一种新型生物硝化抑制剂,在农业生产中可提高氮肥利用率,减少氮素损失。为建立一套超声波提取-气相色谱检测土壤中1,9-癸二醇的方法,分别对超声波提取条件(提取剂、提取次数、液料比、超声时间)和气相色谱检测参数(进样口温度、检测器温度、升温程序)进行研究。结果表明,超声波提取土壤1,9-癸二醇的最佳方法为甲醇作为提取剂超声提取1次,液料比40mL·g^–1,超声时间30 min。气相色谱Agilent8890测定1,9-癸二醇的最佳条件为进样口温度250℃;氢火焰离子化检测器(FID)温度310℃;升温程序:初始柱温60℃,保持2 min,以20℃·min^–1的速率升至150℃,然后以3℃·min^–1的速率升至180℃,保持2 min,最后以20℃·min^–1的速率升至270℃。在最佳提取和测定条件下,不同浓度1,9-癸二醇的加标回收率为90.58%～94.55%。超声提取-气相色谱法检测限低、灵敏度和精密度高,快速高效、重复性好,为今后1,9-癸二醇的实际应用工作...     

The effect of harvest time and pre harvest treatment on the moisture content of Miscanthus × giganteus

This study aims to determine the most appropriate time to harvest Miscanthus × giganteus between January and April, over three possible harvest windows (Jan, Feb and Mar), relative to the harvest method being employed to cut the crop. The moisture content (MC) of biomass cut in January increased compared to the standing crop (control). From an initial MC of 53% in 2009 and 63% in 2010, the control was 12% and 13% lower than Cut Jan after 4 weeks of the treatment in respective years. The MC of Cut Feb was 19% lower than the control after 4 weeks in 2009. Despite Cut Feb being 4% higher than the control after one week in 2010, both treatments reached 34% MC after 3 weeks. A difference of 16% occurred between the Cut Mar and the control after one week in 2009 while in 2010 Cut Mar was 5% higher than the control after one week. Examining the relationship between stem MC, meteorological parameters and evapotranspiration showed that a combination of relative humidity and evaporation rate (Penman equation.) demonstrated the strongest relationship with crop MC. If harvesting early, lower MC can be achieved by cutting and collecting the crop immediately. An increase in the rate of moisture loss can be achieved later in spring by cutting the material and allowing it to dry for a period of time prior to collection if suitable drying conditions occur. An analysis across several sites showed that such conditions are most likely to occur in February.     

Performance of pedigree and various forms of marker-derived relationship coefficients in genomic prediction and their correlations

In recent years, with development and validation of different genotyping panels, several methods have been proposed to build efficient similarity matrices among individuals to be used for genomic selection. Consequently, the estimated genetic parameters from such information may deviate from their counterpart using traditional family information. In this study, we used a pedigree-based numerator relationship matrix ( A ) and three types of marker-based relationship matrices () including two identical by descent, that is and and one identical by state, as well as four Gaussian kernel () similarity kernels with different smoothing parameters to predict yet to be observed phenotypes. Also, we used different kinship matrices that are a linear combination of marker-derived IBD or IBS matrices with A, constructed as , where the weight () assigned to each source of information varied over a grid of values. A Bayesian multiple-trait Gaussian model was fitted to estimate the genetic parameters and compare the prediction accuracy in terms of predictive correlation, mean square error and unbiasedness. Results show that the estimated genetic parameters (heritability and correlations) are affected by the source of the information used to create kinship or the weight placed on the sources of genomic and pedigree information. The superiority of GK -based model depends on the smoothing parameters (θ) so that with an optimum θ value, the GK -based model statistically yielded better performance (higher predictive correlation, lowest MSE and unbiased estimates) and more stable correlations and heritability than the model with IBD, IBS or kinship matrices or any of the linear combinations.     

基于PSO有限元优化直接进给轴伺服动态特性

优化直线电机驱动的直接进给轴伺服动态特性,对提高进给轴的抗干扰性能和加工产品的精度具有重要作用。基于有限元仿真建模的直接进给轴伺服动态特性研究,应用动刚度频谱图来作为伺服动态特性的评价指标,判断直接进给轴共振点所在频段。应用脉冲激励测试进给轴动刚度的方法,依据测量方法确定了直接进给轴的动刚度频谱图,分析了进给轴在不同有限元优化的伺服参数下对动刚度频谱图的影响。通过有限元优化方法和实验相结合,构建了基于有限元优化的伺服参数下直接进给轴动刚度仿真模型。     

三维电极法处理低浓度氨氮废水的研究

养殖场污水处理系统厌氧/好氧阶段的出水,氨氮浓度较低、较难生物降解。针对此类废水中的特征污染物氨氮,研究通过单因素实验和响应面设计实验得到三维电极最优电解条件,即pH值5.0,电解质浓度0.20 mol/L,电压9.86 V,极板间距6.47 cm。在最优条件下处理氨氮浓度为140.00 mg/L的原水,出水氨氮浓度降至34.50 mg/L,低于《鄱阳湖生态经济区水污染物排放标准》(DB36/852-2015)中高效集约发展区氨氮限值。运用X射线衍射仪检测到,在烧结温度为200℃时,活性炭表面附着了α-MnO2、β-MnO2和Mn3O4。结合电化学反应特性,分析所构建的三维电极体系的反应机理。