利用眼肌深度预测猪活体眼肌面积

采用胴体性状测定方法对286头猪胴体进行测定,采用B超测定方法对357头猪活体进行测定,通过分析286头猪胴体测定数据(宰前活体质量、背膘厚、眼肌深、眼肌宽、瘦肉率等)和357头猪活体测定数据(结测质量、背膘厚、眼肌深、眼肌面积),建立胴体与活体2个预测模型并加以验证。结果发现:胴体眼肌深与眼肌面积的相关系数(0.945)高于活体(0.720),胴体模型的决定系数(R2)值(0.894)高于活体模型的R2值(0.519);胴体模型预测值与实测值的散点分布相对一致,而活体模型预测值与实测值的散点分布则较分散;胴体模型预测值与实测值的相关系数为0.497,活体模型为0.672,均为极显著正相关;经t检验,胴体模型预测值与实测值差异不显著,活体模型则差异极显著。本研究结果表明,用眼肌深度预测猪活体眼肌面积是可行的,但预测值的准确性仍需进一步研究。     

地下水埋深对玉米生长发育及水分利用的影响

为研究地下水埋深对作物的生长发育及水分利用的影响,选择具有代表性的夏玉米为研究对象,借助地中渗透仪,通过人工控制设置不同地下水埋深（分别设置0.2,0.4,0.6,0.8,1.0和1.2 m）,探讨地下水埋深对不同生育期夏玉米的形态指标、产量、耗水量及地下水补给量的影响,分析不同地下水埋深条件下水分利用率差异.结果表明：地下水埋深对玉米株高的影响不具有统计学意义,而地下水埋深过浅或过深均会明显抑制植株叶面积指数和茎粗的增长（P〈0.05）,地下水埋深0.4 m时叶面积指数和茎粗最大.随作物生育进程,根系数量和根系干质量随地下水埋深增大,先减小后增大.玉米灌浆前,单株根系伤流量随地下水埋深增大而增大,而灌浆前后则无显著影响.地下水位埋深过深或过浅均影响穗长、秃尖长、穗粒数、百粒质量及经济产量.分析表明,0.53 m为当地玉米产量最优地下水位埋深.玉米生长期内0~80 cm土层土壤含水量随着地下水埋深增大而降低,同一地下水埋深处理玉米生育期内土壤含水量变化幅度较小.夏玉米全生育期耗水量、阶段耗水量及耗水强度随地下水位埋深增大而直线减少,回归方程在P〈0.01水平下具有统计学意义;同样夏玉米全生育期地下水补给量、阶段地下水补给量及地下水补给强度随地下水位埋深增大而直线减少,回归方程在P〈0.01水平下也具有统计学意义.玉米水分利用率随地下水埋深增大而增大,地下水埋深1.2 m处理水分利用率最高.研究成果对江淮丘陵区地下水资源利用及评价、玉米高产高效灌溉制度的制订具有实际意义.     

地埋滴灌点源入渗土壤水分运动规律实验研究

通过室内砂土中进行地埋滴灌的实验,对地埋滴灌在砂土中的适应性进行初步研究,为田间试验布置提供依据。通过分析湿润锋的推移速率、特征点的土壤含水率变化规律,发现湿润锋推移速率先是径向大于垂向,随着灌水时间和灌水量增加,水平方向和垂向的湿润锋和含水率趋于平衡。根据对比滴灌带埋深15和20 cm特征点的含水率变化情况,得出埋深15 cm节水效果更好,更利于作物生长。实验还得出湿润比能作为滴灌灌水参数的指标,由于作物种植的间距和作物根系深度之比基本小于1.0,因此在田间实际灌溉中湿润比应控制在1.0左右。     

典型断面渠道临界水深计算

系统总结了明渠特征水深研究领域的计算方法,评价了各方法的特点;为了优选出典型断面渠道临界水深简捷、通用、精度高、适用范围广的显式计算公式,通过定义包含典型断面几何要素及流量的量纲为一的参数,将目前成果中临界水深的显式计算公式用定义量纲为一的参数进行统一表达,并对其进行简捷性、精度及适用范围的综合评价比较,优选出梯形、圆形、弧底梯形、普通城门洞形、马蹄形等5种典型断面渠道临界水深的显式计算公式;对标准城门洞形断面的临界水深应用最优一致逼近原理,提出以幂函数形式分段表达的新显式计算公式．误差分析表明,在工程常用范围内,由推荐的显式公式所计算的6种典型断面的临界水深,其最大相对误差均小于1％,满足工程设计对精度的要求．该研究可为典型断面排灌渠道的设计及水力计算提供参考．     

不同施肥措施对白土腐殖质组成的影响

以白土稻区4年大田定位试验为基础,设置2种翻耕深度(10 cm、20 cm,分别标记为T10、T20)和4种施肥措施(单施化肥、化肥+畜禽粪肥、化肥+秸秆还田、化肥+绿肥,分别标记为F、F+M、F+S、F+G),通过腐殖质组成修改法分别提取表层土壤水溶性物质、胡敏酸、富里酸和胡敏素,研究不同施肥措施对白土腐殖质各组分碳含量的影响。结果表明:单施化肥措施下,翻耕20 cm处理(T20+F)土壤总有机碳和腐殖质各组分碳含量均低于翻耕10 cm处理(T10+F),但差异未达显著水平。在翻耕20 cm的基础上增施有机肥能显著提高土壤总有机碳和腐殖质各组分碳含量,增施畜禽粪(T20+F+M)、秸秆还田(T20+F+S)和增施绿肥(T20+F+G)3处理的土壤总有机碳、胡敏酸、富里酸和水溶性物质碳含量较T20+F处理分别提高14.57%~30.64%、10.36%~30.57%、0.74%~12.31%和14.25%~26.80%。增施有机肥显著提高胡敏素碳含量,T20+F+M、T20+F+S和T20+F+G处理较T20+F处理提高18.87%~35.78%。4年不同翻耕与施肥措施对白土腐殖质性质未产生显著影响。增施有机肥能一定程度上提高土壤PQ值、胡富比、E4/E6值和色调系数。相关性分析表明,胡敏素、胡敏酸、富里酸碳含量与总有机碳含量间均存在显著或极显著正相关,与水溶性物质碳含量间无明显相关性。     

Effects of lodging of Echinochloa crus-galli L. on the herbicidal efficacy of MTB-951, a mycoherbicide using Drechslera monoceras (Drechsler) Subram. et Jain (= Exserohilum monoceras [Drechsler] Leonard et Suggs)

MTB-951 is a plant pathogen ( Drechslera monoceras ), which was isolated from native Echinochloa spp. in Japan. The conidia of this pathogen were used as the herbicidal active ingredient to control Echinochloa crus-galli L. The herbicidal efficacy of MTB-951 on E. crus-galli was drastically increased with an increasing water depth of between 1 and 10 cm. The efficacy also was increased when shoots were lodged by pushing down on them with a stainless steel net so that all parts of the weed were submerged. These results suggest that the contact area of the leaf surface of E. crus-galli with water is important for infection and that lodging the shoots of E. crus-galli might be effective in increasing the herbicidal efficacy. In order to find other methods to lodge the weed, we investigated several materials, of which diisononyl phthalate (DINP) was found to be the most effective. Using this material as a model, the effect of lodging on the herbicidal efficacy of MTB-951 was examined. The lodging ratio (ratio of the number of the plants lodged on the water surface to that of the total plants) was increased with an increased amount of DINP, between 0.5 and 8 kg ha⁻¹. The herbicidal efficacy of MTB-951 also was increased by DINP and a positive correlation was observed between the lodging ratio and herbicidal efficacy. These results indicate that lodging, which can increase the contact area between the leaf surface and water, enhances the herbicidal efficacy of MTB-951.     

Development of a spot plow providing complete inversion for effective weed control

Tillage for the "complete inversion" of soil, that is, overturning soil slices 180° was proposed, a "spot plow" was developed and tested to accomplish the task, and a simulation model was evaluated to demonstrate the efficacy of the plow on weed control. A 360 mm wide spot plow was designed to operate at a speed of 1.9 m s⁻¹ for the spot plowing with the least possible lateral displacement of the soil slice by utilizing the inertia of the soil slice and securely rotating it. In field experiments, complete spot inversion required an operating speed of at least 1.6 m s⁻¹; at lower speeds, a portion of the soil block was left half-inverted and further lowering led to considerable lateral displacement. The displacement in the forward and lateral directions was minimal, implying that spot plowing is suitable for potential application to and verification of the weed population dynamics model in the field. A simple linear matrix model of the population dynamics of annual weeds was proposed, whereby four layers of soil were set to describe tillage and other ecological events. The effect of tillage on weed control was evaluated by the equilibrium reproduction rate allowed to sustain a stable population of weeds. The simulation model showed that alternately changing the depth of spot plowing had a significant effect on controlling weeds of low-survival-rate seeds, even when some incomplete inversion of the soil slice was taken into account.     

Spatial distribution of soil heavy metal concentrations as indicator of pollution sources at Mount Križna (Great Fatra,central Slovakia)

The objective of this study was to test the suitability of a simple approach to identify the direction from where airborne heavy metals reach the study area as indication of their sources. We examined the distribution of heavy metals in soil profiles and along differently exposed transects. Samples were taken from 10 soils derived from the same parent material along N-, S-, and SE-exposed transects at 0—10, 10—20, and 20—40 cm depth and analyzed for total Al, Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn concentrations. The heavy metal concentrations at 0—10 cm were larger than background concentrations in German arable soils except for Cr (Cd: 0.6—1.8 mg kg^—1; Cr: 39—67; Cu: 40—77; Ni: 87—156; Pb: 48—94; Zn: 71—129; Fe: 26—34 g kg^—1; Mn: 1.1—2.4). Decreasing Cd, Cu, Mn, and Pb concentrations with increasing soil depth pointed at atmospheric inputs. Aluminum and Ni concentrations increased with soil depth. Those of Fe, Cr, and Zn did not change with depth indicating that inputs at most equalled leaching losses. The Pb accumulation in the surface layer (i.e. the ratio between the Pb concentrations at 0—10 to those at 20—40 cm depth) was most pronounced at N-exposed sites; Pb obviously reached Mount Križna mainly by long-range transport from N where several industrial agglomerations are located. Substantial Cd, Cu, and Mn accumulations at the S- and SE-exposed sites indicated local sources such as mining near to the study area which probably are also the reason for slight Cr and Zn accumulations in the SE-exposed soils. Based on a principal component analysis of the total concentrations in the topsoils four metal groups may be distinguished: 1. Cr, Ni, Zn; 2. Mn, Cd; 3. Pb (positive loading), Cu (negative loading); 4. Al, Fe, indicating common sources and distribution patterns. The results demonstrate that the spatial distribution of soil heavy metal concentrations can be used as indication of the location of pollution sources.     

塔里木河下游不同地下水埋深下的土壤种子库特征

本研究根据长期地下水位的监测资料和土壤种子库的萌发试验,分析了塔里木河下游不同地下水埋深下植物样地土壤种子库特征。结果显示,在干旱地区,地下水埋深的高低不仅影响地上植被群落的种类和组成,而且也对土壤种子库的密度和组成具有明显的影响。随着地下水埋深逐渐下降,种子库密度减少、物种多样性下降、生活型逐渐单一。同时地上植被群落与土壤种子库的相似性系数也逐渐降低。本研究不仅有助于丰富国内外关于干旱区土壤种子库的理论研究,而且有利于指导塔里木河下游正在开展的大规模生态恢复实践。