发动机冷却水泵及试验装置的研究

介绍用于发动机冷却水泵的试验装置。该装置的特点是调速范围大，工作介质温度高，可以同时对泵轴进行径向和轴向加载，通过对ＩＶＥＣＯ公司生产的８１４０发动机冷却系统的试验，研究了介质温度对泵的相似定律和性能的影响。     

站库仪表监测系统的防雷及过电压保护

概述了输油泵站和库区防雷设施及过电压保护的现状和特点,分析了目前输油泵站和库区仪表微机监测系统的防雷及过电压保护存在的缺陷,提出了适用于电力系统、建筑防雷和各种电子设施的综合防护原则。针对输油泵站和库区仪表监测系统微电子设备的特点,提出了应采取的防护措施。     

回热型热泵木材干燥机的分析和研究

介绍了空气回热和热泵系统回热两种不同的回热型热泵木村干燥机及其优缺点，阐述了采用空气回热的热泵木材干燥机的优越性，并对其运行特性进行了分析和探讨。通过分析和试验结果表明，采用空气回热的热泵木材干燥机较不采用空气回热的热泵木村干燥机的除湿量大大提高。     

皮下埋藏式灌注器腹腔化疗治疗中晚期消化道癌的临床观察

目的：探讨皮下埋藏式灌注器腹腔化疗治疗消化道恶性肿瘤的疗效。方法：将皮下埋藏式灌注器埋藏于腹壁下，其导管置于恶性肿瘤侵犯区内，于术后１～２周行灌注药物（５－ＦＵ、丝裂霉素），腹腔化疗６～９个疗程。结果：３１例消化道恶性肿瘤患者化疗后近期疗效显著。经ＣＴ、Ｂ超、ＧＩ检查随访１ａ，１７例（５４．８％）患者的恶性肿瘤阴影变小，８０．６％患者健康状态稳定。结论：术后皮下埋藏式灌注器腹腔化疗治疗消化道中晚期恶性肿瘤有良好疗效     

油料储运泵运行工况点的讨论

对离心泵在储运油料过程中的运行工况点进行了分析,指出离心泵的运行工况点是由泵本身的性能曲线和装置阻力曲线共同决定的,所输介质的粘度及是否含有固定颗粒或杂质等都会给泵的运行造成影响。给出了这些影响因素与离心泵性能及装置阻力曲线的关系,推荐了对运行工况点的确定方法,为合理选用离心泵及装置设计提供了参考,为泵的高效可靠运行提供了依据。     

Operational Analysis of Open Untreated Sewage Source Heat Pump System

The effective sewage intake technology is prerequisite for the untreated sewage source heat pump system to run steadily. In terms of the insufficiency of current sewage intake technologies, an open sewage intake integration technology is proposed. The mathematical model and the distinguish basis of critical state are established for the sewage intake characteristic by defining some important operating parameters, such as the blocking coefficient, the contamination density and the section coefficient. Furthermore, the change rule of each critical operation parameter is observed along with the various initial parameters. The result can provide the theoretical basis to design the open intake integration technology.     

Analysis of Radial Forces on the Seal Block in a Compound Gear Pump with 3 Idle Gears

By analyzing the pressure distribution between gears and sealing blocks in compound gear pump with three idlers,the resultant hydraulic forces acting on seal blocks are obtained.The conclusion is the unbalanced resultant hydraulic forces are relatively small in magnitude.In the pump,the inner sealing edges are long and so it s Sealing effect is good,but the outer sealing effect is relatively poor because of its short sealing edges.The little unbalanced force pushes the sealing block to te pumping chamber,therefore it is advantageous to meliorating the pump's sealing effect,thereby to improving it's volumetric efficiency as well.     

Experimental Analysis on Optimal Tail Water Discharge Method of River Water Source Heat Pump

In order to study the influence on water temperature raise of river water source heat pump tail water discharged in different methods, the real sensor network is established by using digital temperature sensors. The simulation experiments of different discharging methods of river water source heat pump are carried out, including submerged-type discharge, surface-type discharge and jet-type discharge with 12 effluent ways. By using weighted average method, the preferred values of such factors as the average temperature raise,the temperature raise variance, the biggest temperature raise value, and the number of temperature measure points above the temperature raise average value are calculated. Moreover, the experiment results are analyzed by the three-dimensional figures of water temperature raise, which shows that jet-type discharge is better than submerged-type discharge and surface-type discharge,and the double-port way is better than single-port way. In addition, the double-port way along with the current in surface-type discharge method is the one that exerts least influence on river water temperature raise.     

Analysis of flow characteristics in thermal-bubble actuated diffuser-nozzle valveless micropump

Based on the different flow resistance characteristic of diffuser/nozzle at the bubble growth and condensation stage, the flow characteristics of thermal-bubble actuated valveless micropump under different ratio of heating, driving frequency and diverging angle and different heating power are numerically investigated. Evaporation and condensation processes are accomplished by Volume of Fluid (VOF) multiphase flow model and User Defined Functions (UDF) interface. The results reveal that with the same ratio of heating time, the volume flow rate increases at first and then decreases with the increasing driving frequency. The micropump has a maximum flow rate of 5.87 μL/min when the driving pulse is 250 Hz at 10% heating ratio. The volume flow rate increases at first then decreases with the enlarging diverging angle when keeping the aspect ratio constant, and it will reach the maximum when the diverging angle is 14°, and it has a higher pressure difference between the diffuser and the nozzle. The average velocity at the diffuser neck is always greater than the nozzle during the entire driving period, the pumping flow rate presents a trend of increasing at first and then flatting with the increasing heating power.