绕流波动特性对不同区域流动传热影响

为研究换热设备后向台阶内置圆柱模型的强化传热机理,采用Fluent进行数值模拟,并通过PIV粒子图像测速方法验证模拟结果的可靠性.研究雷诺数为700后向台阶内置圆柱(X_c/S=0.6,Y_c/S=1.0,d=6 mm)时,后向台阶流道不稳定流动的周期性,以及周期波动对流道不同区域传热的影响.研究结果表明：在过渡流状态下,流道周期速度波动受两基波频率影响,即台阶影响的频率f_s=7.25 Hz和受圆柱影响的频率f_c=14.10 Hz;f_c主要作用在流道上游局部区域,上游回流运动被破坏,努赛尔数瞬时峰值提高2.52倍;f_c促进台阶振动频率f_s提前产生,下游温度梯度减小,瞬时努赛尔数逐渐减小;台阶分离流体与圆柱尾流共同作用使得流道换热效果整体提升,同时壁面摩擦系数也增大.     

叶顶间隙对多相混输泵内流动特性的影响

为了揭示叶顶间隙对多相混输泵内流动特性的影响规律,在进口含气率为10%时,利用ANSYS CFX软件对不同叶顶间隙下泵内气液两相流态进行模拟,同时分析和总结了叶顶间隙对流道内流动特性的影响.研究表明,当叶顶间隙增加时,叶轮叶片进口附近低压区占比明显减少,并且叶轮进出口的压差也在逐渐减小.另外,在靠近叶片顶端时,压力等值线存在偏折现象.随着叶顶间隙逐渐增加,偏折加剧.存在叶顶间隙时,叶轮轮毂附近气相聚集得到了明显的改善,并且随着叶顶间隙的增加,气相在叶顶间隙内靠近叶顶处的聚集现象更加明显,导叶轮毂气相聚集位置沿着流动方向向下游移动.研究结果可为多相混输泵水力优化、性能改善和结构设计等提供依据.同时,研究结果进一步揭示了多相混输泵叶顶间隙流对混输泵性能的影响规律.     

近43年黄河上游来水来沙变化特点

选取黄河头道拐站实测水沙序列(1960-2002年)资料,对水沙序列进行了多时间尺度和趋势识别的小波分析。结果表明:①黄河上游来水来沙量汛期所占比例减少,而非汛期所占比例增加;在年际变化上,水沙量逐年减少;同时,水沙相关关系具有一定的变化;②黄河上游水沙序列具有相同的多时间尺度(准周期)变化,但同一尺度下,水沙所处的丰枯变化并不一致;③年水沙序列趋势变化基本一致,20世纪80年代以来,两者存在明显减少趋势;但在非汛期,两者的趋势变化有较大区别。     

掩埋多孔毛管水流特性的试验研究

以渗灌毛管的灌水试验为研究对象,通过试验分析得到了掩埋毛管流量和压力的变化特性。对于任一出水孔,随着供水时间的延长,压力水头和总水头都在不断增大。但是,这个增加值并不大,仅仅只有最大压力值的10%。随着四周土壤含水量的增加,孔口内外水势梯度不断减小,出水速率也逐渐减小,流量和压力随管长方向不断减小。由于流量随时间不断减小,使得水头损失也不断减小,压力随时间增大。同时在试验中还发现,水流运动的界面并不是管道的出水孔界面,而是在出水孔四周形成的不规则多边形界面。     

抽蓄机组甩负荷过程压力脉动及流动噪声仿真

为了研究水泵水轮机发电模式下甩负荷过渡过程压力脉动特性及其对流动诱导噪声的影响,以国内某抽水蓄能电站机组为研究对象,基于网格壁面滑移技术与分离涡湍流模型,通过ANSYS软件对瞬态流场进行数值模拟计算,并将所得流场信号作为声场源在LMS软件中进一步开展流动诱导噪声的仿真.结果表明因2个无叶区流态分别受动静干涉(固定导叶与...     

兰州百合同源四倍体诱导及其基因组大小估算

兰州百合(2n=2x=24)是重要的“药食同源”植物,进行其种质创新和基因组大小分析对于丰富其种质资源和生物学信息具有重要意义。以兰州百合的种子和试管小鳞茎为试验材料,通过秋水仙素浸泡诱导染色体加倍,经流式细胞仪倍性检测获得的同源四倍体植株分别有10和4株,四倍体诱导率分别为21.11%和33.27%。为了估算兰州百合基因组大小,以小麦品种“中国春”为内标,通过流式细胞仪测算兰州百合二倍体和四倍体植株中的DNA含量,得出兰州百合基因组为64.9 Gbp,是“中国春”核基因组的4倍。     

基于PIV技术的圆形循环水养殖池流场

为研究进水管的设置距离和角度对双管进水式圆形循环水养殖池水动力特性的影响,该研究通过模型试验的方法,利用粒子图像测速技术（Particle Image Velocimetry,PIV）测量了不同进水管设置方式下养殖池内的流场。试验设计了3组进水管距池壁距离（进水管与池壁的最近距离,即进水管设置距离d）,每组距离工况下设计了8组进水角度（出水方向与养殖池切线形成的锐角,即进水管设置角度α）。利用PIV技术测量了不同工况下距离池底1 cm水层的流场,从水动力特征量（平均流速vavg和速度均匀系数U）分析进水管设置方式对养殖池水动力特性的影响。试验结果表明进水管设置方式明显影响养殖池的水动力特性：d=0时,随着α的增加,平均流速整体呈现先增大后下降的规律,在α=45°时取得最大值,但流场均匀系数随角度的增加而逐渐增加;d=1/4 r（r为养殖池半径）时,随着α的增加,平均流速和流场均匀系数都先缓慢增加然后再下降,分别在α=40°和30°时取得最大值;d=1/2 r时,随着α的增加,平均流速和流场均匀系数整体都呈现逐渐下降的趋势。综合比较24个试验工况的平均流速vavg和速度均匀系数U,建议将进水管设置为d=1/4 r,α=30°～40°,以期使养殖池内水动力特征有利于固体颗粒物的运动汇集,提升养殖池的集排污能力。该文研究成果可以为工厂化循环水圆形养殖池进水管设置方式提供参考。     

MacCormack算法在长输管道瞬变流动仿真中的应用

为了提高长输管道仿真精度和速率,基于MacCormack格式基本原理和流动方程建立了长输液体管道水力瞬变流动仿真模型。以某管道为例,分别采用该仿真算法和特征线法模拟了阀门关闭和流量增加引起的瞬变流动,并探讨了MacCormack格式中不同边界条件处理方法及Courant常数值对模拟结果的影响。结果表明:MacCormack格式可用于精确仿真长输管道瞬变流动过程,采用特征线法求解预估层边界参数后,其振荡幅度、收敛速度均优于特征线仿真方法;同时,采用特征线法处理MacCormack格式边界条件较线性外插法更易收敛。研究成果可为长输管道瞬变流动仿真提供参考。(图8,表2,参22)     

The Fluorescent Characterization and Analysis of Two Brucella Attenuated Vaccine Infecting Mouse Macrophagocyte

The experiment was conducted to discuss the difference of binding time of green fluorescent protein B.melitensis M5 (GFP-M5) and B.abortus S19 (GFP-S19) infecting the mouse macrophagocyte (RAW264.7),lysosome,endoplasmic reticulum and golgi body in the initial stage and compare the binding rate of GFP-M5,GFP-S19 with organelle in different timeline,respectively,by confocal laser scanning microscope (CLSM) and flow cytometry.The result showed that GFP-M5 and GFP-S19 were successfully constructed.The intracellular survival ability of Brucella M5,Brucella S19,GFP-M5 and GFP-S19 were not obvisouly affected after infecting RAW264.7.GFP-M5 and GFP-S19 could enter the macrophagocyte in 30 mins,and in 2 h the Brucella could reach lysosome,endoplasmic reticulum and golgi body.In addition,the binding time for two attenuated vaccine did not show differences in 1,2,3 and 4 h.The content of GFP⁺ cell produced by RAW264.7 infected by GFP-M5 and GFP-S19 did not show significant differences (P>0.05).Therefore,the two strains did not have significant differences in the invasion ability in the initial stage of infecting host cell.     

Evaluation of transpulmonary ultrasound dilution cardiac output in piglets: accuracy,precision and trending ability with room temperature injectate

ObjectiveTranspulmonary ultrasound dilution (TPUD) is a minimally invasive technique to measure cardiac output (CO) using a 1 mL kg^–1 isotonic 37 °C saline injectate indicator. The objective was to evaluate the performance of TPUD using a room temperature saline injectate.Study designProspective experimental trial.AnimalsA total of seven anesthetized male Yorkshire piglets.MethodsPiglets aged 1 month and weighing 7.7–9.0 kg were anesthetized with detomidine–ketamine–hydromorphone–isoflurane and a pulmonary artery flow probe (PAFP) placed via a median sternotomy. The thoracic cavity remained open during measurement of CO by PAFP and TPUD. The TPUD indicators of 1 mL kg^–1 0.9% saline at 37 °C and 20 °C were compared during infusions of phenylephrine and dobutamine, blood withdrawal and replacement. Bias, limits of agreement (LoAs) and percentage error (PE) between each iteration of PAFP and TPUD were measured with Bland–Altman plots. Trending ability via concordance, angular bias and radial LoA were compared.ResultsBland–Altman plots showed negligible bias with varying LoAs. PEs of 22% and 38% were found for 37 °C and 20 °C saline injectates, respectively. In the four-quadrant plots, the concordance rate was 94% and 100% for measurements obtained with 37 °C and 20 °C saline injectates, respectively. Angular bias for both were < ±5 °, with radial LoA < ±7 °.ConclusionsTPUD was accurate when using 1 mL kg^–1 of isotonic saline at 37 °C in a range of CO within 0.2–0.8 L minute^–1, and it reliably tracked positive and negative changes in CO. Room temperature (20 °C) indicator was less accurate but equally able to track direction of changes in CO.Clinical relevanceThe use of room temperature injectates allows an easy, readily available clinical application of TPUD CO monitoring while preserving the trending ability of the monitor.