Numerical Simulation of Flow field and Temperature field in Combustion Chamber Widened Suddenly

The flowfield and temperature field are numerically Simulated by the mathematical model of the fluid flow and heat transfer in circular combustion chamber widened suddenly. The distributions and influence factors of the flow field and temperature field are studied in it. The results have the guiding significance for the design of combustion chamber. The mathematical models can serve as the quantitative analysis methods for design.     

Water model study on flow optimization of five streams L-type tundish

In this paper, the water model method is used to optimize the flow behavior of asymmetrical five streams L-type tundish in a steelmaking plant. The results show that the optimization plan is set up with turbulence suppressor T+ vice guide wall D2+ main guide wall with three holes (D1a) which consists of top two holes with 25° inclination and one hole with 30° inclination below. With this plan, the time which the colorants reach to the outlets increases, the difference of response time in all outlets decreases, the peak concentration of the RTD reduces, the existence time of high concentration liquid steel extends, and the ratio of dead zone in each streams reduces.     

Influence of the Flood-Control-Projects on the Hydrodynamic State of the Rivers Confluence in Chongqing

Though the Flood-Control-Projects along Yantze River and Jialing River in Chongqing may well improve the urban traffic and construction,it may change the river hydrodynamic characters.There may be two consequences,one is to reduce the size of cross section and the other is to change the river shape,such as the curvature radius.The phenomena of the local backwater and velocity variety are obvious,which result in some problems for the navigation: sediment,transport and so on.In this paper, the study object is the Flood-Control-Projects and Yangtse River and Jialing River,and the aim is to study the influence of the Flood-Control-Projects on the hydrodynamic state of the two rivers.Using the numerical technique,with the two rivers hydrodynamic model the flow field's change of river after completion of Flood-Control-Projects is simulated and the reasons caused by the change are analyzed.     

Simulation of the penetration rate (ROP) of the air percussion drilling

It is difficult to calculate the penetration rate (ROP) of percussion drilling. In the early research, the empirical or semiempirical formulae of the ROP are derived from the laboratory or field data collected by the researchers. However, the ROP value of the formulae is not as accurate as that in the field. Benefiting from the dynamic model, the geometric structure model and the theory of the roller cone bit, the mathematical model of the hammer bit, the mathematical model of the true bottom hole and the mathematical model between the tooth and the rock of the hammer bit are established. Hence the ROP of the air percussion drilling can be predicted by simulation. Field tests show the models are reliable and the results are coincident with that in the field. The research can help to redesign the hammer bit and optimize the drilling parameters.     

发动机用平板型空滤器流动阻力特性分析和改进

为减小平板型空滤器流动阻力以增大进气量,对平板型空滤器流动阻力特性开展了实验研究,获得了空滤器流动阻力随流量变化的规律和阻力构成成分。阻力随流量的增大而加速增大,滤芯阻力约占整个空滤器阻力的一半,入口流量为120 m 3/h时,总阻力为915.3 Pa,滤芯阻力为426.4 Pa。在实验获得滤芯阻力参数的基础上,提出采用多孔介质跃升模型对平板型空滤器内部流场开展三维数值仿真分析,结果表明,仿真结果与实验结果比较吻合,最大误差为5.67%。滤芯阻力同样约占整个阻力的一半,另一半阻力主要为出口处阻力,其余壁面阻力约占15%。最后,在实验和仿真分析的基础上,提出了改进模型并进行了仿真分析。结果表明,改进模型阻力有较大程度的下降,入口流量为120 m 3/h时,总阻力为588.2 Pa,较原始模型下降了32.2%;增大空滤器流通横截面积是减小阻力以增大进气量的有效手段,改进空滤器壁面的平滑性是补充措施。     

汽车催化转化器起燃过程的数值模拟

应用CFD技术，采用大型的计算流体力学软件Fluent软件建立催化转化器数学模型，并对其起燃过程进行了数值模拟研究。结果表明：催化转化器起燃过程的数值模拟基本上反映了催化转化器起燃过程的实际情况，所得到的速度场、温度场、浓度场和压力分布趋势正确合理。     

切线泵流动特征的整流场数值模拟

对单级切线泵在设计工况进行了定常流动数值模拟，分析了叶轮流道及蜗壳内的液体流动情况。结果表明，切线泵内流场非常复杂，叶轮进口有明显冲击，叶轮各流道的速度、压力差异很大，环形蜗壳内流动呈现旋涡推进特征，上、下游流动有强烈的相互作用，整机流场不具有对称性；环形蜗壳的几何结构以及流场上、下游的相互作用是导致整机流场非对称特性的主要原因。计算结果为进一步改进结构、提高性能、减小水力损失提供了理论依据。     

潮州三百门电厂冷却水排放的数值模拟研究

海湾及潮汐河口的冷却水工程研究近年来受到人们的重视，由于受到潮汐的影响，其冷却水布置及热污染特性比河道及水库型更为复杂。采用数值模拟的方法，首先对电厂附近的潮流特性及冷却水输移扩散进行模拟计算，研究了电厂近海水域的水动力结构及其对冷却水排放的影响，给出电厂取水温升及热污染范围，为电厂取水设计工作提供依据。