直通式调节阀内部流场分析

基于CFD对直通式调节阀内部流场进行了二维数值模拟,并得到了内部流动参数的可视化图形。对比25%和5%两种开度下,阀门处的压力,速度以及能量损失都存在很大的差异。25%开度下的压力、流速有明显的下降趋势,而5%开度下压力和速度则迅速变化。+两种开度下产生的涡流位置不同,5%开度下能量损失比25%开度下的要大。     

电压空间矢量脉宽调制的简单算法

在电压空间矢量脉宽调制(SVPWM)控制技术原理的基础上,提出了一种简单快速算法,该算法只有普通的四则运算,计算变得非常简单,消除了常规的空间矢量控制算法中由于三角函数和无理数的近似计算而带来的计算误差及影响计算精度和速度的缺点,使结果更加准确。因而更适合应用于基于DSP 的数字化控制。理论分析和大量的MATLAB仿真结果表明,该算法具有谐波含量低、直流电压利用率高的优点。     

基于HYDRUS-2D的地下滴灌下水分运移数值模拟研究

利用HYDRUS-2D软件模拟了地下滴灌条件下滴头周围黏壤土的土壤水分动态,并与田间观测进行对比;通过分析不同滴头流量对试验地土壤湿润模式的影响,明确了最佳灌水技术参数。结果表明,HYDRUS-2D软件模拟结果与观测值一致,体积含水率均方根误差为1.2%~4.5%,湿润范围均方根误差变化范围为2.1~3.87cm。     

FLUENT软件及其在植保机械方面的应用

FLUENT软件是流体力学中通用性较强的商业软件之一，由于FLUENT软件的应用，节省了大量的人力和物力。对实际应用有重大的指导作用。为此，通过简述FLUENT在植保机械方面的应用实例，提出了FLUENT在植保机械方面的发展前景。     

砌石拱坝加高倍厚的三维接触仿真

对砌石拱坝的加高倍厚中新、老坝体结构面，用有限元软件ANSYS结合接触理论进行计算，并分析结果得出：温升、水压力和淤沙压力使结合面上的接触压力增大，从而接触摩擦应力较大，有利于结合面的结合，而结合面在温降的作用下有脱离的趋势。     

Simulation on the Characteristics of Flow Pattern in Sprial uP-flow Reactor

In order to analyze the reason why the Spiral Up-flow Reactor system has excellent removal effect of COD, N and P, the authors use PHOENICS, a computational fluid dynamics program, to investigate the hydraulic characteristics and flow model of the anaerobic part of Spiral uP-flow reactor. The result shows that the fluid in the reactor unit flowed upward by the spiral way, and that flow pattern was combined by plug flow and complete-mix flow, and that the percentage of plug flow was about sixty-five percent. Spiral Up-flow Reactor units the Characteristics of PFR and CSTR, which makes it work well.     

不同花生品种侧枝发育动态与产量性状研究

花生一级侧枝发育具有不均衡性。第一、二对侧枝出现早，伸长快，其他一级侧枝出现晚，伸长慢。86036－26－1第一、二对侧枝发育相对较早，而其他一级侧枝发育较晚；海花1号和豫花1号第一、二对发育相对较晚，而其他一级发育较快；豫花7号和鲁花9号居中。海花1号一级侧枝及第一对侧枝的二级侧枝数最多，86036－26－1的一级侧枝数及第一对侧枝的二级侧枝数量少。在花针期之前第一对侧枝的伸长与主茎基本同步；花针期之后，第一对侧枝伸长速度超过主茎。86036－26－1的一级侧枝长及株高居首位。86036－26－1第一、二对侧枝饱果率，产量居第一，豫花7号居第二。海花1号虽然荚果数较多，但第一、二对侧枝孢果率较低，产量也较低；鲁花9号居中。     

Analysis and FEM Simulation of the Forming Process of Front Bumper Bracket

The processing characteristics of the front bumper bracket are analyzed,and a reasonable process scheme is worked out.The three-dimensional sheet metal forming analysis software PAM-STAMP are adopted to simulate the bracket's drawing process.Then the surface of die is proved fine through analyzing the FLD diagrams and the forming results.An economical and optimized die structure is decided,and a complete set of dies of the bracket is designed.The spacing block is added in the sizing mold,which control the size precision of end products and assembling columns actively,and finally the certified products.The material utility and the labor productivity are raised,the production cost is saved,and the mold design quality and the efficiency are improved effectively.     

Two Types Modules for the Boiler Attached to 330 MW Unit

Boiler is an important facility in power plant , the safety and economy of unit is affected by it. Studying the dynamic of boiler can improve the knowledge about boiler , which is important for. Features of MMS are introduced based on MMS simulation setting, and the real time capable module and non real time capable module are compared from principle. Real time capable dynamic model of boiler and non real time capable dynamic model of boiler of 330 MW unit are established . The experimental results show that the dynamic process of two type model accords with the mechanism of the object , at the same time, the validity of real time capable module is discussed .