Pinning Theory of Fermi Energy and Surface State Measurement of ZnSnO3 Gas Sensitive Material

In order to research the state of energy bands and gain and loss of electrons on the surface of ZnSnO_(3),it is put forward that Pinning theory of Fermi energy is applied to development of gas sensitive materials.The relative position between surface state and conduction band on surface of zinc tin complex oxide(ZnSnO_(3)) gas sensitive material has been investigated by utilizing oxidation redox couple,FeCl_(2)/ FeCl_(3),which have high surface state.Fermi energy is pinned at about 0.2 eV below conduction band E_(cs)on the surface of ZnSnO_(3).It has been determined that additives doping ratio,addition concentration and working atmosphere have no effect on this value.Therefore,pinning theory of Fermi energy has been verified by using this method.     

Realizing 3 Layers Transport Model in the Communication Between Embedded System and PC

This article puts forward a 3 Layers Model for the communication between embedded system and PC. It is based on the speciality of them and the TCP/IP model. The model defines the communicate process of embedded system to be three layers: Transport Layer, Control Layer and Application Layer. Each layer serves for its higher-up. It can keep the efficiency and credibility of the communicate process and the authors prove and analyse that in the article. the concept of the model is also suitable for Bluetooth, IrDA and other kinds of communication about embedded system.     

Stability Contrast of Landslide Disaster After Repeating Control

Xiang-jiapo landslide,which consists of shallow layer,middle layer and deep layer,is a multi-landslide with several layers.Influenced by geological condition and rainfall,it have not obtained good effect even after three-time control.Because the distortion of landslide increase so fast, the government planed to control the landslide for the forth time.Based on monitoring data of the landslide movement,the paper make a constrast analysis of 3D numerical simulation's calculating between the formal control and the forth time control by a non-linear finite elements programm ABAQUS.Both results of numerical simulation and monitoring indicate that the forth time control have achieved good effect.     

油初始坐果机制研究

以成年油木奈树为材料,对其初始坐果进行了研究。结果表明,盛花后2周内,油木奈出现大量的落花落果;幼果(子房)低水平的GA1 3与油木奈的落花落果高峰关系密切,而内源细胞分裂素ZRs和[diH]ZRs以及ABA与幼果(子房)的生长呈显著的正相关;初始坐果期,油木奈的雌配子体发育缓慢,且有相当数量的胚囊中途退化、败育,无法正常受精,从而导致其大量的落花落果。文中就油木奈的初始坐果机制进行了讨论。     

Si3N4陶瓷/GCr15钢摩擦副复配添加剂协同效应

对Si3N4陶瓷/GCr15钢副在油性剂T406与极压抗磨剂P120复配作用下的摩擦磨损性质进行了对比试验研究.采用SSX-550型扫描电子显微镜观察试件的磨损表面形貌,并用能量散射谱仪进行了磨损表面的化学元素分析.结果表明,T406与P120复配对该摩擦副有较明显的减磨抗磨协同作用,最佳复配比例为1.0%T406＋2.0%P120.能谱分析结果表明,T406与P120复配时,产生的协同作用主要是在GCr15钢摩擦表面形成的化学反应膜,Si3N4陶瓷/GCr15钢副的磨损形式主要为磨料磨损和化学腐蚀磨损.     

ZrO_2对Al_2O_3基泡沫陶瓷过滤器的性能影响

以Al2O3为主要成分的料浆中加入ZrO2,采用有机泡沫浸渍法,用1560℃烧结制备Al2O3基泡沫陶瓷过滤器,并测定不同ZrO2含量过滤器样品的抗压强度、热震次数并观察其显微结构,实验结果表明:Al2O3基泡沫陶瓷的抗压强度、抗热震性能随ZrO2加入量的增加先增加,而后略有下降。在ZrO2加入量为20%(重量)时制品的抗压强度及抗热震性能最佳,其最高抗压强度达2.31 MPa,1100℃热震循环次数为16次。     

离心泵叶轮三维造型

离心泵叶轮是离心泵的最主要的部件,它的设计与造型至关重要。通过利用读入数据和、pro/e,对离心泵叶轮进行三维造型,为下一步的分析计算打下基础。     

带分流叶片的离心泵叶轮三维贴体网格生成

采用泊松方程进行带分流叶片的离心泵叶轮内三维贴体网格的自动生成 ,并通过源项控制来满足网格的正交性及调整网格疏密。计算时根据边界处网格线正交的控制角和控制距离的几何约束确定边界条件 ,利用分块粘接技术生成了带分流叶片离心泵叶轮内的三维分块结构化贴体网格 ,从而提高了流场流动分析中前处理环节的效率和精度 ,能使在湍流计算中广泛应用的壁面函数法的条件容易满足 ,并能使普遍采用的压力第二边界条件直接用于计算中 ,还能满足差分要求 ,减小离散误差。     

低比转数离心泵叶轮出口紊流流动结构分析

在叶轮内三维紊流流动数值计算的基础上，从介质能量的观点，分析了不同工况下低比转数离心泵叶轮出口处的紊流流动结构。数值计算采用SIMPLEC算法，在贴体坐标系下求解Navier—Stokes方程，紊流模型采用标准的κ—ε模型。计算结果表明，在叶轮的出口附近靠近吸力面一侧存在一个低能区，而压力面一侧能量相对较高。这与有关文献中所指出的离心风机的“射流—尾流”结构相对应。当偏离设计工况时，该低能区的范围和强度略有增加，相对应的叶轮效率也降低。计算结果与水泵在这些工况下的效率实验结果相一致，说明低能区的存在是影响低比转数离心泵效率的重要因素。