Recommendations on Shrinkage and Temperature Reinforcements in Concrete Slabs

The mechanism of shrinkage cracking is discussed with a simple member, which is fully restrained and subjected only to an axial restraining force caused by shrinkage, while a simple procedure is presented for the determination of the number and spacing of the cracks and the average crack width. With the simple model, some examples are shown to compare the provisions for minimum shrinkage and temperature reinforcement in GB 50010-2002 Code, ACI 318-02 Code and AS 3600-1988 Code. The results show that the provisions in GB 50010-2002 Code are too weak in comparison with the others. Finally, some recommendations are proposed.     

聚氨酯木材胶粘剂的研究(Ⅰ)--化学组成对粘接力学性能的影响

以多亚甲基多苯基多异氰酸酯（PAPI）和聚醚多元醇为原料合成了一种单组分、室温湿固化的端异氰酸酯聚氨酯胶粘剂。本研究考察了物料的化学组成对胶粘剂粘接木材的力学性能产生的影响。实验表明,与改性二苯基二异氰酸酯（MDI）相比,PAPI合成的胶粘剂对木材粘接干压剪强度提高了60％;将相对分子质量（Mw）为800、1000和2000的聚氧化乙烯二醇（PED）、Mw为300和3000的聚氧化丙烯三醇（N303和N330）以及聚四氢呋喃一氧化丙烯二醇（NG220）按优化的比例复合使用,以改性胺和有机锡复合催化,可有效提高粘接木材的干和湿压剪强度、固化速率以及木破率。Fr-IR光谱证实聚醚多元醇的-OH与PAPI的-NCO反应生成了氨基甲酸酯（-NHCOO-）,但N—H和G=O均以氢键形式存在。     

不同水性高分子异氰酸酯胶对人工林木材胶合性能的影响

采用同一类型的高分子化合物、填料和乳胶按不同配比组成2种主剂,然后与贮存期不等的交联剂组成不同的水性高分子异氰酸酯胶黏剂(API),用来黏接杉木、杨木、巨桉、尾巨桉、柠檬桉和窿缘桉等6种人工林木材试样以研究 API主剂特征和交联剂贮存时间对人工林木材胶合性能的影响。试验结果表明:1)API主剂特征显著影响6种人工林木材的胶合性能。2)随着交联剂贮存期的增长,人工林试材的胶合性能有降低趋势,但胶合杉木、杨树、巨桉和尾巨桉4 种人工林木材时仍能达到标准要求。     

提高钢琴键盘尺寸稳定性的研究

文章采用PEG的分子量、质量体积浓度、压力的变化作为影响因子,探讨了不同条件下的PEG对鱼鳞云杉尺寸稳定性能的影响,结果表明,PEG处理过的鱼鳞云杉具有较高的尺寸稳定性,PEG的分子量、处理液浓度、抽真空度和浸渍加压压力对木材尺寸稳定性都有一定的影响。     

速生人工林桉树木材材色处理初步研究

试验用漂白剂、酸性染料和其他化学药剂,采用单纯漂白、单纯染色、先漂白再染色和化学着色等4种不同的方案对人工林桉树木材进行材色改良处理研究.结果发现:单纯漂白可获得一定的材色改良效果;硫化物类、过硫酸铵类的药剂配方漂白效果不明显;硼氢化钠类的药剂配方可得到一定的漂白效果;双氧水类、次氯酸钠类的药剂配方可得到很好的漂白效果.单纯染色比较难获得好的材色处理效果.采用先漂白后染色的方法,获得的材色过于鲜艳.采用化学着色的方法,可获得较理想的材色改良效果;草酸类药剂配方着色效果明显,可消除材色缺陷,根据不同的配方和处理工艺可获得从浅粉红色到红棕色的色调;用双氧水做活性剂,引入带发色团的化学药剂,材色改良效果明显,通过调整配方药品的浓度和处理工艺可获得从浅黄色到橙黄色的不同色调和较佳的材质.     

鳞毛蕨(Dryopteris filix-mas)天山云杉林倒木更新分析

对西天山国家级自然保护区1 hm2典型鳞毛蕨天山云杉林临时标准地内,倒木对更新的影响进行了研究.结果表明:①研究区中所有倒木的平均倾倒方向为西北方向,具有更新个体存在的倒木平均倾倒方向为东北方向;②倒木的倾倒方向对倒木的更新没有显著影响(F3,51=0.645,P=0.589),而倒木的腐朽等级对倒木的更新存在显著影响(F2,51=3.215,P=0.048);③不同腐朽等级倒木上幼苗、幼树的出现概率不同,能为幼苗、幼树生长提供生境的倒木只有腐朽等级高的Ⅲ,Ⅳ,Ⅴ级倒木,且倒木腐朽等级越高,对幼苗、幼树的生长越有利.     

西安市生态足迹与生态安全的动态研究

本文在生态足迹原理的基础上,提出生态压力指数、生态占用指数和生态经济协调指数3个概念,并将其作为生态安全评价的指标体系。利用该方法对西安市1978—2003年的生态足迹与生态安全进行了定量研究。结果表明西安市人均生态足迹由1978年的1.0517hm2逐年增加至2003年的1.4419 hm2,而实际人均生态承载力则波动在0.3182(0.2759—0.3539)hm2左右,人均生态赤字从1978年的0.712 hm2增至2003年的1.166 hm2。生态压力指数从1978年的1.38逐年增至2003年的4.21,同期的生态占用指数从0.47增至0.66,生态经济协调指数由0.34降低为0.16。说明西安市现有的发展模式是不可持续的,生态环境处于极不安全状态,社会经济发展与生态环境的协调性很差。     

Drop size dependence of soil-water contact angle in relation to the droplet geometry and line tension

The soil-water contact angle is used as a measure of the surface hydrophobicity of soils. The contact angle for particular solid–liquid combination is considered to vary with the drop size. In this paper, we focused on examining the drop size dependence of contact angle on soil surfaces compared with homogeneous solid surfaces, and determining its relation to the droplet geometry and line tension. The contact angle estimated using geometric parameters of the droplets (θ _G) showed decreasing trend with increasing drop size from 5 to 50?µL irrespective of the deformations in the droplet shape in larger drops. This was considered to be a result of the corresponding deviations of the geometric parameters of the droplets. The directly measured contact angle (θ _A) first decreased and then increased with increasing drop size from 5 to 50?µL. The drop size at lowest θ _A for hydrophobized silica sand with 1?g?kg^–1 stearic acid (SA) and the acryl surfaces was 20?µL, whereas that for hydrophobized silica sand with 5?g?kg^–1 SA and siliconed paper was 30?µL. The decrease in θ _A with increasing drop size was explained as a result of the line tension effect using the modified Young's equation. Despite the surface heterogeneity, all the surfaces tested in this study showed positive line tensions on the order of 10?µJ?m^–1. Irrespective of the heterogeneity of the surfaces, the θ _A in this experiment agreed with the modified Young's equation for drop sizes up to about 20–30?µL, where the θ _A and θ _G were also in good agreement. Drop size dependence of contact angle was independent of the level of surface hydrophobicity. The θ _A on all the examined surfaces started to increase with increasing drop size when the deformation index, I _d, exceeded 5%, where the wetting radius, R exceeded the capillary length. The increase in θ _A with increasing drop size was attributed to the deformations of water drops due to the effect of gravity.