3-RPS并联机构奇异位形及工作空间研究

提出一种求解并联机构无奇异位形工作空间的方法。通过分析3-RPS并联机构在奇异位形时动平台的微分运动与结构约束及关节约束的关系，得到机构奇异位形判别方程和奇异位形曲面方程。探索了工作空间边界，综合分析了机构奇异位形与工作空间的关系。合理选择机构结构参数和关节变化范围，得到了无奇异位形的工作空间。     

灌溉渠系流量最优调配的0-1规划模型

本文根据灌溉配水渠系的运行特点,提出在一定轮期和来水流量限制条件下实现下级配水渠最优组合及其配水时间最优排序的一种0-1规划模型,实例运算表明,这种方法可有效减少无效弃水和闸门调节次数,同时对渠道横断面的设计有参考意义。     

三道湾水电站正常溢洪洞及泄洪排

试验表明，三道湾水电站原设计存在以下问题：泄洪排沙洞单独全开运行工况下，其进口上方存在贯通性吸气漏斗漩涡；正常溢洪洞进口侧收缩十分严重，泄流量不足，闸后存在水翅、折冲波等不良流态，下游消能效果不佳；针对实际情况，试验通过在泄洪排沙洞进口增设消涡格栅，在正常溢洪洞进口设置椭圆形导墙、延长闸后收缩段，下游采用扩散挑流消能等措施，很好地解决了上述问题。     

海河二道闸和防潮闸优化调度研究

汛期为腾空海河河道并保证二道闸下咸水不致上溯，二道闸闸下水位应控制在1.0m左右。利用一维非恒定流模型对海河自西河闸至入海口河段进行数值模拟，研究了西河闸分流量为80、100、120m3/s3种情况下，海河防潮闸和二道闸优化调度结果。     

Simulation on the Characteristics of Flow Pattern in Sprial uP-flow Reactor

In order to analyze the reason why the Spiral Up-flow Reactor system has excellent removal effect of COD, N and P, the authors use PHOENICS, a computational fluid dynamics program, to investigate the hydraulic characteristics and flow model of the anaerobic part of Spiral uP-flow reactor. The result shows that the fluid in the reactor unit flowed upward by the spiral way, and that flow pattern was combined by plug flow and complete-mix flow, and that the percentage of plug flow was about sixty-five percent. Spiral Up-flow Reactor units the Characteristics of PFR and CSTR, which makes it work well.     

Distributed Power Flow Method Based on Ward Equivalent

With interconnecting and developing of power system, the problem of power flow computation on dispersed data resource need to be solved. A new distributed computation method of power flow based on Ward equivalent is presented. According to master-slaver splitting principle, multi-area interconnected power system is divided into master-slaver areas. Boundary buses in different areas are defined as different bus-types. Neighborhood areas are equivalent by Ward equivalent principle, and the equivalent injection power and equivalent impedance are worked out. Power flows from master area to slaver areas are solved by Newton method, and the equivalent injection power and equivalent impedance on the boundary are modified by their solutions. The process above repeats until to convergence. The proposed distributed power flow method takes full advantage of the information of power, voltage, network configuration in neighborhood areas, so it is better on convergence and quality of solution. The proposed algorithm is testified by IEEE 14-bus system and a practical 181-bus system.     

NETWORK FEOW APPROACH TO RELIABILITY EVALUATION IN IARGE SCALE NETWORKS BY MIXING INCREASING ELOW WITH DECREASING FLOW

Based on the maximum flow principle about networks, a network flow approach to reliability evaluation in large scale netwerks ty mixing inereasing flow with decreasing flow is proposed in this paper.This approach gets the initial flow of each branch in a r.etwork associated with a state of the retwork by decreasing flows of some branches correlative to another state of the network.As a result, the number of flow compute required can be reduced enormously.The numerical example shows that the approach is powerful. The comparison of this approach with the minimal cutset one is also given in this paper.     

Artificial Neural Networks Models for Flow Stress during High Temperature Plastic Deformation of Al-Li Alloy

Using gained experimental data to develop the models of stable flow stresses at high temperature plastic deformation by statistical methods for alloy materials, precision of the models is poor and at the same time the processes of modeling are complicated with great workload. On the basis of the data obtained on Gleeble-1500 Thermal Simulator,the predicting models for the relation between stable flow stress during high temperature plastic deformation and deformation strain, strain rate and temperature for 1420 Al-Li alloy have been developed with BP Artificial Neural Network method. The results show that the model on basis of BPNN is practical and it reflects the real feature of the deforming process. It states that the difference between the real value and the output of the model is in order of 5 percent.