THE STUDY OF STRAIN FATIGUE CRACK PROPAGATION BEHAVOURS OF VANADIUM BEARING HSLA STEEL

In this paper, the strain fatigue: crack propagation rates of vanadium bearing HSLA steel with different micro-structures are measured under constant load conditions, and the relationship between the crack propagation rate and the microstructures of steel is also studied.     

A Study on the Mathematical Models for Two Dimensional Guillotine Cullting-stock

Based on the analysis and study on some existed models for two-dimensional Guillotine Cutting-Stock problem, it is pointed out that some kinds of the models may miss some good cutting patterns,and some may result in inadequate solutions because of only considering the patterns with the smallest waste. A kind of revised two-dimensional cutting-stock models are developed,which transform the two-dimensional problem into the one-dimensional one using the dimension-decreasing heuristic method and whose initial patterns are considered comprehensively. In this kind of models, not only the least waste,but also the other constraints,such as the demands and the relative area of the order plates are considered.     

A Study on the Practical Algorithm for One Dimensional Equal Stock Cutting Problem

Based on alalysing the mathematical models for one dimensional equal stock cutting problem,a knapsack column generation algorithm has been constructed,which is a successive approximate algorithm for the practical engineering.In the end of this paper,some computational examples have been presented,which show that the convergence and optimum results of the algorithm are quite good.     

黄麻工艺纤维细度的研究

研究表明：圆果种比长果种工艺纤维支数高65公支左右；品种间差异极显著；工艺纤维细度与单株原麻重等5个经济性状呈极显著负相关，与出麻率等性状呈显著正相关；麻株各部位中以中部工艺纤维支数最高，梢部次之，基部最低；适时播种、适当密植、适量适时施肥，适时早收等栽培技术措施能提高工艺纤维支数。通过对构成产量和工     

几个外引水稻品种在河南沿黄地区的表现

通过对几个外引水稻品种在河南沿黄地区引种试验，表明杂交稻生长速度快，抽穗较晚，但分蘖力强、成穗率高、穗粒数多，产量的增产潜力较大。除金世纪外其他几个品种与豫粳6号相比基本持平，但产量也有不同程度的提高。但金世纪品质与豫粳6号相比有较大的提高，产量也提高。     

小黄鱼热泵干燥工艺及设备选型分析

研究了不同热泵干燥温度下小黄鱼的干燥特性,并对其干燥品质进行分析。结果表明在干燥温度55℃、铺放密度为6.48 kg/m2的条件下干燥时间为13.5 h,干燥品质最优。在综合考虑能耗、企业加工条件和产品品质的前提下,将生产工艺参数确定为:干燥温度60℃、铺放密度为6~7 kg/m2,干燥时间为10~12 h。根据企业日处理量5.5~6.0 t的加工要求,通过对产能核算及加工成本计算,确定设备选型方案为:1台GHRH-510型热泵干燥机与2台GHRH-340型热泵干燥机,该方案投资回报期短,社会效益明显。     

Modeling soil water dynamics in a drip-irrigated intercropping field under plastic mulch

Intercropping, drip irrigation, and the use of plastic mulch are important management practices, which can, when utilized simultaneously, increase crop production and save irrigation water. Investigating soil water dynamics in the root zone of the intercropping field under such conditions is essential in order to understand the combined effects of these practices and to promote their wider use. However, not much work has been done to investigate soil water dynamics in the root zone of drip-irrigated, strip intercropping fields under plastic mulch. Three field experiments with different irrigation treatments (high T1, moderate T2, and low T3) were conducted to evaluate soil water contents (SWC) at different locations, for different irrigation treatments, and with respect to dripper lines and plants (corn and tomatoes). Experimental data were then used to calibrate the HYDRUS (2D/3D) model. Comparison between experimental data and model simulations showed that HYDRUS (2D/3D) described different irrigation events and SWC in the root zone well, with average relative errors of 10.8, 9.5, and 11.6 % for irrigation treatments T1, T2, and T3, respectively, and with corresponding root mean square errors of 0.043, 0.035, and 0.040 cm³ cm^?3, respectively. The results showed that the SWC in the shallow root zone (0–40 cm) was lower under non-mulched locations than under mulched locations, irrespective of the irrigation treatment, while no significant differences in the SWC were observed in the deeper root zone (40–100 cm). The SWC in the shallow root zone was significantly higher for the high irrigation treatment (T1) than for the low irrigation treatment, while, again, no differences were observed in the deeper root zone. Simulations of two-dimensional SWC distributions revealed that the low irrigation treatment (T3) produced serious severe water stress (with SWCs near the wilting point) in the 30–40 cm part of the root zone, and that using separate drip emitter lines for each crop is well suited for producing the optimal soil water distribution pattern in the root zone of the intercropping field. The results of this study can be very useful in designing an optimal irrigation plan for intercropped fields.     

金属注射成形技术在喷雾机零件制造中的应用

概述了金属注射成形技术的工艺过程和特点，给出了在喷雾机喷雾头组件这一典型农机零件上的应用实例，并对喷雾头组件用注射成形工艺制造中粘结剂成分的选择、混炼工艺、脱脂方法和烧结过程等进行了探索。通过研究制造出了尺寸精度和力学性能均满足要求的产品，产品致密度达到98．5％。生产工艺得到明显简化。     

车辆表面脉动压力的试验研究

对车辆表面脉动压力与气流噪声的关系进行了讨论，说明了偶极子源噪声在车辆气流噪声中占主导地位，而车辆气流噪声中的偶极子源噪声又取决于车辆的表面脉动压力，阐述了研究车辆表面脉动压力对进一步研究和控制车辆气流噪声具有的重要意义。在此基础上，对车辆表面脉动压力的分布、频率特性及其与车速的关系进行了试验研究，得到了一些有意义的结论。     

基于框架理论的变电站操作票自动生成系统

介绍了一种基于框架理论的变电站操作票自动生成系统。该系统用框架知识表示法来描述电力系统的设备参数，建构了一个直观的、层次分明的数据结构。通过融合框架理论于面向对象的语言VC 中，开发出了一个集通用、实用、智能于一体的操作票专家系统。